Oxidación de etanol y ácido fórmico en nanocristales de ... · realización del doctorado, ya...
Transcript of Oxidación de etanol y ácido fórmico en nanocristales de ... · realización del doctorado, ya...
Oxidación de etanol y ácido fórmico en nanocristales de platino: Electrocatálisis y reactividad superficial
Ethanol and formic acid oxidation in platinum nanocrystals: Electrocatalysis and surface reactivity
Carlos Antonio Busó Rogero
Instituto Universitario de Electroquímica
Facultad de Ciencias
Oxidación de etanol y ácido fórmico en nanocristales de
platino: Electrocatálisis y reactividad superficial
Ethanol and formic acid oxidation in platinum
nanocrystals: Electrocatalysis and surface reactivity
Carlos Antonio Busó Rogero
Tesis presentada para aspirar al grado de
DOCTOR POR LA UNIVERSIDAD DE ALICANTE
MENCIÓN DE DOCTOR INTERNACIONAL
Programa de Doctorado Electroquímica, Ciencia y Tecnología RD 99/2011
Dirigida por:
Enrique Herrero Rodríguez Catedrático de Universidad en el
Dpto. de Química Física de la
Universidad de Alicante
Juan Miguel Feliu Martínez Catedrático de Universidad en el
Dpto. de Química Física de la
Universidad de Alicante
Alicante, Mayo 2016
Agradecimientos/Acknowledgements
Los años en los cuales se realiza la tesis doctoral son un período de continuo
aprendizaje tanto desde el punto de vista formativo como en el personal. Su realización
requiere indudablemente de una gran cantidad de trabajo imposible de realizar sin ayuda.
Por ello, me gustaría agradecer a todas las personas que hayan contribuido con su granito
de arena a esta tesis doctoral, especialmente a:
• Enrique Herrero, por introducirme en el laboratorio hace ya unos años, y por
haber sido el principal supervisor de mi tesis. A pesar de ser una de las personas
más atareadas que conozco, gracias por estar siempre dispuesto a ayudarme en lo
necesario y a resolverme cualquier duda (y no sólo de Electroquímica).
• Juan M. Feliu, la persona que más pasión demuestra hacia la Electroquímica de
Superficies, por ser codirector de la tesis, por el suministro de nuevos electrodos
monocristalinos siempre que hayan sido necesarios y por los consejos dados
durante estos años.
• José Solla y Fran Vidal, por toda la ayuda al proporcionarme las muestras de
nanopartículas necesarias para llevar a cabo gran parte de los trabajos aquí
presentados, por la enseñanza del método para trabajar correctamente con
nanopartículas y por la rápida resolución de cualquier duda surgida al trabajar con
ellas. También quisiera agradecer a ambos vuestra involucración en casi todos los
trabajos que he logrado publicar.
• Prof. Behm, for accepting me in the Ulm University and for his contribution in the
DEMS experiments discussion presented in this thesis. Thanks also to Sylvain
Brimaud for supervising my work there and to Zenonas Jusys for his useful help
in the laboratory during the performance of the experiments.
• Victor Climent, por su ayuda ante cualquier problema relacionado con la
Electroquímica o cualquier cuestión general del laboratorio. También gracias a
Antonio Rodes por sus útiles consejos para la correcta elaboración de
experimentos espectroelectroquímicos.
• Manuel J.S. Farías y Vitali Grozovski, por la contribución directa en la
elaboración de estos trabajos y por poner siempre a mi disposición vuestra
experiencia en investigación relacionada con la Electroquímica.
Agradecimientos/Acknowledgements
• A todas las personas que han colaborado en la asistencia técnica durante la
realización del doctorado, ya sean técnicos de laboratorio, vidrieros o técnicos del
taller mecánico, por la paciencia que han tenido conmigo, por las ideas aportadas
y por la rapidez en entregar el material requerido.
• A compañeros del laboratorio que han contribuido directamente a la mejora de los
resultados experimentales de la tesis: Antonio Berná, que tuvo mucha paciencia
en mis inicios y me enseñó muchos ‘trucos’ trabajando en el laboratorio; Marta
Figueiredo, también por sus sugerencias que han influido en el éxito de mis
experimentos y que sigo utilizando a día de hoy; el excéntrico William
Cheuquepan, por su colaboración en el laboratorio de IR, resolviendo cualquier
duda y buscando la perfección en los experimentos; y a Ana Boronat, una de las
personas con más bondad que conozco, por ofrecerme su ayuda en todo momento
sin esperar nada a cambio.
• A todos mis compañeros de la Universidad de Alicante, que de una forma u otra
han hecho estos años más agradables y que se han llegado a convertir en buenos
amigos tras compartir tanto tiempo de trabajo y risas: Rubén G, Alberto V, Sara
Chumillas, Jonnathan, Juan Victor, Betzhy, Ricardo, Rosi, Rubén R., Valentín,
Fran, Gisele, Paula, Andrea, Ana María, Miguel Ángel, Naiara, Leti, Alicia,
David S., Alonso, Paco Montilla, Ana C., María P., María José, Sara L., Carolina,
Omar O., Ariadna, Nacho, David V, Irene, Milena, Dejan, Fabián, Néstor, Laura
P, Aroldo, Moha.… Habéis creado en mí grandes recuerdos, como las cenas de
San Alberto o los derbys de fútbol sala entre el grupo de Superficies y el de
Polímeros.
• Mis amigos (vosotros sabéis quiénes sois), ya sea de la carrera, los del grupo de
Alicante o los que he tenido la suerte de conocer durante los años de doctorado
gracias a actividades derivadas de esta tesis, los cuales siempre me han ofrecido
su apoyo comprendiendo la dificultad de la exhaustiva dedicación a una tesis
doctoral. Especial agradecimiento a Bea y Mayer por sus continuos ánimos y por
las risas en las quedadas que hemos realizado en estos años.
• Mi familia, especialmente mi madre, mi padre y mi hermana, que también me han
apoyado y han soportado mi mal humor en épocas con alta cargas de estrés y,
simplemente, por quererme tal como soy.
A mis padres y mi hermana
Índice
Abstract ................................................................................................................. I
CAPÍTULO 1: Síntesis
1.1 Introducción ..................................................................................................... 3
1.1.1 Oxidación de ácido fórmico en Pt .............................................................................. 10
1.1.2 Oxidación de etanol en Pt ........................................................................................... 13
1.2 Técnicas experimentales ................................................................................ 18
1.2.1 Técnicas electroquímicas ............................................................................................ 18
1.2.2 Espectroscopía infrarroja (IR) in situ ......................................................................... 22
1.2.3 Espectroscopía infrarroja ATR acoplada con espectrometría de masas DEMS ........ 27
1.2.4 Microscopia electrónica de transmisión (TEM) ......................................................... 32
1.3 Caracterización superficial ............................................................................. 33
1.3.1 Monocristales de platino............................................................................................. 33
1.3.2 Nanopartículas de platino........................................................................................... 39
1.4 Objetivo de la tesis ......................................................................................... 45
1.5 Referencias ..................................................................................................... 48
CAPÍTULO 2: Efecto de la estructura superficial y del anión para la
oxidación de etanol en nanopartículas de platino
Resumen ................................................................................................................ 61
2.1 Introduction .................................................................................................... 66
2.2 Experimental .................................................................................................. 68
2.3 Results and discussion .................................................................................... 71
2.3.1 Ethanol oxidation on single crystal electrodes ........................................................... 71
2.3.2 Electrochemical characterization of Pt nanoparticles ................................................ 73
2.3.3 Ethanol oxidation on Pt nanoparticles. ...................................................................... 74
2.3.4 FTIR experiments of ethanol oxidation. ...................................................................... 78
2.4 Conclusions .................................................................................................... 85
2.5 References ...................................................................................................... 86
Índice
CAPÍTULO 3: Oxidación de etanol en nanopartículas de platino con
diferente forma controlada a diferentes pHs: estudio combinado de espectroscopía IR
in situ y espectrometría de masas en línea
Resumen ................................................................................................................ 93
3.1 Introduction .................................................................................................... 98
3.2 Experimental ................................................................................................ 101
3.3 Results and discussion ................................................................................. 105
3.3.1 Electrochemical characterization ............................................................................. 105
3.3.2 Ethanol oxidation at low pHs ................................................................................... 106
3.3.3 DEMS experiments ................................................................................................... 109
3.3.4 Ethanol stripping experiments .................................................................................. 114
3.4 Conclusions .................................................................................................. 119
3.5 References .................................................................................................... 120
CAPÍTULO 4: Oxidación de etanol en electrodos monocristalinos de Pt:
efecto de la estructura superficial en medio alcalino
Resumen .............................................................................................................. 125
4.1 Introduction .................................................................................................. 130
4.2 Experimental Section ................................................................................... 133
4.3 Results .......................................................................................................... 135
4.3.1 Ethanol oxidation on Pt basal planes ....................................................................... 135
4.3.2 FTIR experiments of ethanol oxidation .................................................................... 142
4.4 Discussion .................................................................................................... 146
4.5 Conclusions .................................................................................................. 153
4.6 References .................................................................................................... 154
CAPÍTULO 5: Oxidación de etanol de etanol en nanopartículas de platino:
efecto de la estructura superficial y de la agregación de partículas
Resumen .............................................................................................................. 159
5.1 Introduction .................................................................................................. 164
5.2 Experimental ................................................................................................ 168
Índice
5.3 Results and discussion .................................................................................. 171
5.3.1 Characterization of shape-controlled Pt nanoparticles ........................................... 171
5.3.2 Ethanol oxidation on preferentially shaped Pt nanoparticles.................................. 173
5.3.3 FTIR experiments for ethanol oxidation .................................................................. 176
5.3.4 Characterization of Pt nanoparticles supported on carbon ..................................... 178
5.3.5 Aggregation effect in ethanol oxidation ................................................................... 181
5.4 Conclusions .................................................................................................. 185
5.5 References .................................................................................................... 186
CAPÍTULO 6: Electrooxidación de ácido fórmico con nanopartículas de
platino de forma controlada decoradas con talio: mejora en la actividad
electrocatalítica
Resumen .............................................................................................................. 193
6.1 Introduction .................................................................................................. 198
6.2 Experimental ................................................................................................ 200
6.3 Results and discussion .................................................................................. 202
6.3.1 Formic acid oxidation on Tl-modified Pt single crystal electrodes ......................... 202
6.3.2 Electrochemical characterization of Tl modified Pt nanoparticles ......................... 205
6.3.3 Formic acid oxidation on Tl modified shape controlled Pt nanoparticles ............... 206
6.3.4 FTIR experiments of formic acid oxidation on Tl-decorated Pt nanoparticles ........ 210
6.3.5 Effect of formic acid concentration .......................................................................... 212
6.4 Conclusions .................................................................................................. 216
6.5 References .................................................................................................... 217
CAPÍTULO 7: Nanopartículas de platino de forma controlada modificada
con adátomos para la oxidación de etanol
Resumen .............................................................................................................. 223
7.1 Introduction .................................................................................................. 228
7.2 Experimental ................................................................................................ 231
7.3 Results and discussion .................................................................................. 233
7.3.1 Electrochemical characterization of modified Pt nanoparticles .............................. 233
Índice
7.3.2 Ethanol oxidation in acidic medium ......................................................................... 235
7.3.3 Ethanol oxidation in alkaline solutions. ................................................................... 242
7.4 Conclusions .................................................................................................. 246
7.5 References .................................................................................................... 247
CAPÍTULO 8: Conclusiones ......................................................................... 253
Lista de publicaciones..................................................................................... 263
Abstract
I
Abstract
In the present thesis, fundamental studies for the oxidation of small organic
molecules (ethanol and formic acid) have been performed. These molecules can be used as
reactive in the anode for the fuel cell technology. For this purpose, platinum catalysts in
the form of single crystal surfaces and nanoparticles have been employed. The final aim is
to find the best catalyst for achieving the highest possible activity at the lower
overpotential, avoiding the formation of undesired products, such as CO in the formic acid
oxidation process and acetic acid/acetate in the case of ethanol oxidation. The results
presented here will allow a better understanding of these oxidation processes, and how
different factors, such the surface structure, the solution pH, and the agglomeration of the
nanoparticles, affect to the catalytic response of the electrodes and can help to develop
better electrocatalysts. In addition, the modification of the surface reactivity by deposition
of foreign adatoms, seeking an enhancement in the catalytic activity of the nanoparticles
for the considered reactions, will be also studied.
In these studies, electrochemical techniques, such as cyclic voltammetry and
chronoamperometry, have been used for characterizing the platinum electrodes and
studying the reactivity of the electrodes for the two reactions. The possible intermediates
and final products of the reaction have been characterized using the spectroelectrochemical
techniques Fourier Transformed-Infrared Reflection-Absorption Spectroscopy (FT-
IRRAS) with external reflection and Attenuated Total Reflection-Fourier Transform
Infrared (ATR-FTIR). Differential Electrochemical Mass Spectrometry (DEMS) is also
employed for obtaining quantitative data about the oxidation mechanism.
The results of Colmati et. al. [1] with single crystal electrodes in acidic solutions
demonstrated that ethanol oxidation reaction on platinum is a structure sensitive reaction.
For Pt(111) electrodes only acetic acid is produced, whereas for Pt(110) and, especially,
Pt(100) electrodes the C-C bond scission is also taking place, leading to the formation of
adsorbed CO before the complete oxidation to CO2. Chapter 2 shows the extension of these
studies to practical catalysts, using nanoparticles with preferential shape [2, 3] by means of
electrochemical and spectroscopic techniques. The results show that the behavior of the
Abstract
II
nanoparticles can be rationalized using the data obtained with the single crystal electrodes.
On the other hand, anion adsorption effects are also investigated. It is found that there are
no significant differences in the oxidation currents in H2SO4 and HClO4 electrolytes, i.e.,
irrespectively of the presence of specifically adsorbed anions in the electrolyte. The
formation of acetic acid, which is adsorbed specifically on the electrode surface as acetate
and is always formed regardless of the presence of 111 or 100 domains, justifies the
absence of differences.
The oxidation mechanism for ethanol oxidation is strongly affected by the solution
pH. For this reason, chapter 3 studies how pH influences the ratio of products using DEMS
in flow cell conditions [4]. The pH is always maintained below 4 for avoiding carbonate
formation, which can interfere in the analysis of the results. Preferentially shaped (100)Pt
and (111)Pt nanoparticles samples are used for these experiments. These two samples were
selected because they represent the paradigm of the two distinct behaviors shown in
chapter 2. (100)Pt nanoparticles are more active than (111)Pt nanoparticles for the
formation of C1 fragments (CO or CHx), as the better efficiency for CO2 production
demonstrates, 10% vs. 5% respectively. The results also indicate that the increase of pH
leads to a lower rate for the C-C bond breaking and a stabilization of the CHx fragments.
Continuing with the pH effect on ethanol oxidation, the studies in alkaline solutions
are started in chapter 4. These studies can be important for the development of alkaline fuel
cells, where the lower corrosive properties of the medium will allow the use of non-noble
metals as catalysts. First of all, single crystal electrodes with a well-known crystallographic
structure are used for a better understanding of the reaction, following the same strategy
used in the studies in acidic media [1, 5], that is, the behavior of the low index planes and
the effect of the presence of 100 and 110 steps on 111 terraces for ethanol oxidation
will be studied. The results, which are compared with previous works done in similar
conditions [6-8], show that the Pt(111) electrode has the highest activity, followed by the
Pt(110) and Pt(100) electrodes. This reactivity trend is the opposite to that found in acidic
medium. Similarly, the 100 and 110 steps in 111 terraces do not increase the
currents for ethanol oxidation in alkaline solutions, despite lower onset potential values are
obtained. In addition, IR experiments confirm the poor selectivity of the platinum
electrodes for the CO2 formation, producing quasi exclusively acetate. The IR spectra,
Abstract
III
which was analyzed using a similar strategy than that employed in ref. [9], demonstrate
that the amount of carbonate formed on the three electrodes is negligible. On the other
hand, the huge deactivation detected for all the platinum surfaces is attributed to the
polymerization of the acetaldehyde produced from the ethanol oxidation reaction. The
deactivation process affects especially the 111 ordered domains.
In the same way as in chapter 2, ethanol oxidation on shape-controlled platinum
nanoparticles is studied in chapter 5 for alkaline solutions, in the same conditions of the
previous results with single crystal electrodes. The affinity for the acetate formation
observed in chapter 4 is corroborated with the shape-controlled platinum nanoparticle
samples, and the trend for the activity in the Pt nanoparticles electrodes also agrees with
the previous results. In addition to the surface structure effect, the agglomeration effects in
the reactivity are also attempted. For that purpose, nanoparticle samples dispersed in
carbon are employed. The importance of attaining a good dispersion of the nanoparticles
on the support for measuring the correct catalytic activity is highlighted. This good
dispersion of the nanoparticles on the support assures that all of them could participate in
the reaction. The best dispersion are obtained using the method of Garsany and co-workers
[10], which used a slow rotation of the support during the deposition of the nanoparticles.
The effects of the modification of the shape-controlled platinum nanoparticles
composition, specifically the (100)Pt and (111)Pt nanoparticles, with adatoms in its
reactivity are studied in chapters 6 and 7. The first studies are conducted for the formic
acid oxidation reaction, trying to increase the rate for CO2 production and avoiding the CO
formation. Modifications of the Pt electrodes with adsorbed Bi, As or Pd have been shown
large enhancement in the currents measured for the formic acid oxidation reaction [11-13].
In the present case, Tl is deposited on the platinum surfaces. For both (100)Pt and (111)Pt
nanoparticles, Tl adsorption shows a positive effect, shifting the onset potential to lower
values (around 0.1 V), with the absence of CO formation. Specifically, (100)Pt
nanoparticles show higher activity than (111)Pt nanoparticles. FTIR experiments indicate
that the presence of Tl inhibits the formation of CO. Moreover, the effect of formic acid
concentration for the Tl-modified Pt nanoparticles electrodes is also investigated,
displaying some complexity in the oxidation mechanism and suggesting additional species
involved in this reaction.
Abstract
IV
Finally, chapter 7 deals with the effect of adatoms for ethanol oxidation. The study
was carried out both in acidic and alkaline media using (100)Pt or (111)Pt nanoparticles.
From the different adatoms studied in the literature for this reaction (Sn [14], Ru [15], Os
[16], Bi [17] or Pb [18, 19]), Sn, Rh, Ru and Pb were selected since they show higher
catalysis. As before, the target is an electrode which displays higher currents and lower
overpotentials for the ethanol oxidation reaction. In 0.5 M H2SO4, the best activity is found
for Pt-Sn; the onset potential shifts towards more negative values, mainly for the (100)Pt
nanoparticles. This effect is attributed to the catalysis of the oxidation of CO to CO2. For
the (111)Pt nanoparticles, higher currents are also observed, due to a catalytic effect in the
oxidation of ethanol to acetic acid at high Sn coverages [20]. For 0.1 M NaOH, very minor
positive effects are found for the Pt-Rh, Pt-Sn and Pt-Pb surfaces, mainly in the (100)Pt
nanoparticles samples.
In summary, fundamental studies about the effect of the surface structure and
composition for the ethanol oxidation reaction are carried out in this thesis. These studies
have used shape-controlled platinum nanoparticles, which is the form of the catalysts more
interesting from the applied point of view. These works have been complemented with
studies on single crystal electrodes, to better understand the reaction mechanism. The
important effect of the solution pH in the reaction mechanism is highlighted. Finally, the
effect of the surface composition is studied. The catalysis of the formic acid oxidation is
more effective, due to the simpler reaction mechanism. For the ethanol oxidation, the
different steps in the reaction (dehydrogenation, C-C bond scission, oxidation to CO and
finally to CO2) probably requires complex strategies to find a suitable electrocatalyst.
Abstract
V
References
[1] F. Colmati, G. Tremiliosi-Filho, E. R. Gonzalez, A. Berná, E. Herrero and J. M. Feliu, ''Surface structure effects on the electrochemical oxidation of ethanol on platinum single crystal electrodes'' Faraday Discussions 2008, 140, 379-397.
[2] J. Solla-Gullón, F. J. Vidal-Iglesias, A. López-Cudero, E. Garnier, J. M. Feliu and A. Aldaz, ''Shape-dependent electrocatalysis: methanol and formic acid electrooxidation on preferentially oriented Pt nanoparticles'' Physical Chemistry Chemical Physics 2008, 10, 3689-3698.
[3] V. Grozovski, J. Solla-Gullón, V. Climent, E. Herrero and J. M. Feliu, ''Formic Acid Oxidation on Shape-Controlled Pt Nanoparticles Studied by Pulsed Voltammetry'' Journal of Physical Chemistry C 2010, 114, 13802-13812.
[4] M. Heinen, Y. X. Chen, Z. Jusys and R. J. Behm, ''In situ ATR-FTIRS coupled with on-line DEMS under controlled mass transport conditions - A novel tool for electrocatalytic reaction studies'' Electrochimica Acta 2007, 52, 5634-5643.
[5] F. Colmati, G. Tremiliosi-Filho, E. R. Gonzalez, A. Berná, E. Herrero and J. M. Feliu, ''The role of the steps in the cleavage of the C-C bond during ethanol oxidation on platinum electrodes'' Physical Chemistry Chemical Physics 2009, 11, 9114-9123.
[6] M. López-Atalaya, E. Morallón, F. Cases, J. L. Vázquez and J. M. Pérez, ''Electrochemical oxidation of ethanol on Pt(hkl) basal surfaces in NaOH and Na2CO3 media'' Journal of Power Sources 1994, 52, 109-117.
[7] S. C. S. Lai and M. T. M. Koper, ''Ethanol electro-oxidation on platinum in alkaline media'' Physical Chemistry Chemical Physics 2009, 11, 10446-10456.
[8] P. A. Christensen, S. W. M. Jones and A. Hamnett, ''In Situ FTIR Studies of Ethanol Oxidation at Polycrystalline Pt in Alkaline Solution'' Journal of Physical Chemistry C 2012, 116, 24681-24689.
[9] Z.-Y. Zhou, Q. Wang, J.-L. Lin, N. Tian and S.-G. Sun, ''In situ FTIR spectroscopic studies of electrooxidation of ethanol on Pd electrode in alkaline media'' Electrochimica Acta 2010, 55, 7995-7999.
[10] Y. Garsany, I. L. Singer and K. E. Swider-Lyons, ''Impact of film drying procedures on RDE characterization of Pt/VC electrocatalysts'' Journal of Electroanalytical Chemistry 2011, 662, 396-406.
[11] S. A. Campbell and R. Parsons, ''Effect of Bi and Sn adatoms on formic acid and methanol oxidation at well defined platinum surfaces'' Journal of the Chemical Society, Faraday Transactions 1992, 88, 833-841.
[12] F. J. Vidal-Iglesias, A. López-Cudero, J. Solla-Gullón and J. M. Feliu, ''Towards More Active and Stable Electrocatalysts for Formic Acid Electrooxidation: Antimony-Decorated Octahedral Platinum Nanoparticles'' Angewandte Chemie-International Edition 2013, 52, 964-967.
[13] F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero, A. Aldaz and J. M. Feliu, ''Pd Adatom Decorated (100) Preferentially Oriented Pt Nanoparticles for Formic Acid Electrooxidation'' Angewandte Chemie-International Edition 2010, 49, 6998-7001.
[14] Q. W. Zheng, C. H. Fan, C. H. Zhen, Z. Y. Zhou and S. G. Sun, ''Irreversible adsorption of Sn adatoms on basal planes of Pt single crystal and its impact on electrooxidation of ethanol'' Electrochimica Acta 2008, 53, 6081-6088.
[15] V. Del Colle, A. Berná, G. Tremiliosi-Filho, E. Herrero and J. M. Feliu, ''Ethanol electrooxidation onto stepped surfaces modified by Ru deposition: electrochemical and spectroscopic studies'' Physical Chemistry Chemical Physics 2008, 10, 3766-3773.
[16] V. Del Colle, V. Santos and G. Tremiliosi-Filho, ''Comparative Electrochemical and Spectroscopic Studies of Ethanol Oxidation on Pt(h,k,l) Modified by Osmium Nanoislands'' Electrocatalysis 2010, 1, 144-158.
Abstract
VI
[17] M. C. Figueiredo, A. Santasalo-Aarnio, F. J. Vidal-Iglesias, J. Solla-Gullón, J. M. Feliu, K. Kontturi and T. Kallio, ''Tailoring properties of platinum supported catalysts by irreversible adsorbed adatoms toward ethanol oxidation for direct ethanol fuel cells'' Applied Catalysis B-Environmental 2013, 140, 378-385.
[18] Q. G. He, B. Shyam, K. Macounova, P. Krtil, D. Ramaker and S. Mukerjee, ''Dramatically Enhanced Cleavage of the C-C Bond Using an Electrocatalytically Coupled Reaction'' Journal of the American Chemical Society 2012, 134, 8655-8661.
[19] P. A. Christensen, S. W. M. Jones and A. Hamnett, ''An in situ FTIR spectroscopic study of the electrochemical oxidation of ethanol at a Pb-modified polycrystalline Pt electrode immersed in aqueous KOH'' Physical Chemistry Chemical Physics 2013, 15, 17268-17276.
[20] V. Del Colle, J. Souza-Garcia, G. Tremiliosi-Filho, E. Herrero and J. M. Feliu, ''Electrochemical and spectroscopic studies of ethanol oxidation on Pt stepped surfaces modified by tin adatoms'' Physical Chemistry Chemical Physics 2011, 13, 12163-12172.
Capítulo 1: Síntesis
3
Capítulo 1: Síntesis
1.1 Introducción
La Electroquímica focaliza sus estudios en los procesos de transferencia de carga que
ocurren en la interfase entre un conductor electrónico y un conductor iónico o directamente
entre dos conductores iónicos [1]. De acuerdo con Bockris y Reddy [2], históricamente los
estudios de la Electroquímica se dividen en dos grandes grupos:
• Iónica: Trata de sistemas homogéneos relacionados con iones en disolución
(acuosa o no), sales iónicas o electrolitos sólidos.
• Electródica: Estudia lo que sucede en una interfase electrodo/electrolito a
través de una transferencia de electrones.
Después de los primeros experimentos que evidenciaban la existencia de la
electroquímica (Galvani en 1791, Volta en 1799 y Faraday en 1831), los estudios
posteriores vinieron marcados por la publicación de Nernst sobre la termodinámica de las
pilas galvánicas (1891), que decantaron la investigación hacia las reacciones en equilibrio
y las propiedades termodinámicas de las disoluciones. Esta situación cambia cuando se
empiezan a considerar algunas publicaciones realizadas anteriormente acerca de la cinética
electroquímica (Butler en 1924, Volmer en 1930 o Frumkin en la década de los años 30),
lo cual provocó una orientación de todas las investigaciones electroquímicas hacia la
cinética electródica a partir de entonces.
La Electroquímica electródica también se considera una parte de la ciencia de
superficies, ya que estudia los fenómenos físicos y químicos ocurridos en la interfase
metal-disolución, atendiendo tanto a sus propiedades macroscópicas (normalmente carga,
potencial y corriente eléctrica) como a las microscópicas. Por tanto, es importante realizar
un análisis adecuado de la estructura metálica a nivel atómico. Para un correcto estudio de
Capítulo 1: Síntesis
4
la interfase metálica hasta niveles microscópicos, en primera aproximación, son necesarias
técnicas de caracterización superficial que precisan condiciones de ultra alto vacío (ultra
high vacuum, UHV, en sus siglas en inglés). Estas técnicas favorecen el control del
máximo número de variables posibles para mejorar la caracterización, como por ejemplo
trabajar a bajas presiones para evitar la contaminación de la superficie metálica (en la
sección 1.3 se presentan algunos ejemplos de estas técnicas). Esta metodología deberá
extenderse posteriormente a las condiciones electroquímicas in-situ: en disolución y con
potencial aplicado. Sin embargo, esa caracterización UHV-Electroquímica requiere
técnicas experimentales muy costosas y no siempre el resultado es satisfactorio, por lo que
conviene algún método alternativo más sencillo para realizarla, siendo capaz de encontrar
las relaciones existentes entre las propiedades macroscópicas y microscópicas de una
superficie metálica en condiciones electroquímicas (por ejemplo, mediante una simple
voltametría cíclica). De este modo será posible obtener información relevante en
Electroquímica de Superficies.
En la actualidad, la Electroquímica está presente en muchos aspectos de la vida
cotidiana, como en el caso de la fabricación de biosensores [3, 4], electroanálisis [5, 6],
células solares [7], tratamiento de aguas [8], electrosíntesis [9, 10], corrosión [11] y
almacenamiento de energía [12, 13], entre otras. No obstante, una de las aplicaciones más
importantes de la Electroquímica es la de la obtención de energía a partir de baterías, las
cuales se clasifican en dos tipos: primarias (donde la batería produce energía hasta que el
reactivo químico encargado de ello se agota) o secundarias, las cuales se pueden recargar.
Ejemplos de baterías son los acumuladores, las baterías de flujo o las pilas de combustible
[14-17]. Dentro de los dispositivos electroquímicos primarios para la obtención de energía,
el grupo particular de las pilas de combustible tiene por objeto generar electricidad a partir
de un suministro de combustible externo y oxígeno mediante una reacción química
controlada, originando la formación de productos y el abastecimiento de energía eléctrica a
un circuito externo. Su funcionamiento es similar al de las baterías, con la salvedad de que
necesitan un suministro continuo de los reactivos empleados.
Las pilas de combustible presentan ventajas respecto a otras fuentes de energía, como
el nulo deterioro de los electrodos y la baja contaminación para el medio ambiente
producto de las disoluciones utilizadas, además de las altas eficiencias observadas debido a
Introducción
5
la inexistencia de procesos térmicos o mecánicos asociados a la producción de la energía
eléctrica. Por tanto, las pilas de combustible se pueden considerar como un recurso
energético alternativo, limpio y útil para el futuro teniendo en cuenta el agotamiento de las
fuentes de energía fósiles.
Desde la primera pila de combustible fabricada a partir de hidrógeno y oxígeno
empleando electrodos de platino, publicada por Groove en 1839, se han diseñado multitud
de pilas de combustible utilizando pequeñas moléculas orgánicas e inorgánicas en el
ánodo, además del citado hidrógeno. Las principales tecnologías desarrolladas para estos
dispositivos actualmente se pueden clasificar atendiendo al reactivo o al tipo de electrolito
utilizado [17, 18]:
• Pilas de combustible alcalinas (AFC): Una de las razones para el uso de
electrolitos alcalinos es el de abrir la posibilidad a la utilización de
catalizadores menos nobles. Como en las pilas de combustible más
habituales, utilizan hidrógeno en el ánodo y oxígeno en el cátodo. Se han
llegado a obtener potencias de hasta 0.8 W cm-2 en prototipos realizados para
la NASA, con eficiencias en torno al 50% y un tiempo de vida de hasta 10000
horas.
• Pilas de combustible de ácido fosfórico (PAFC): En estas pilas de
combustible, el ácido fosfórico actúa como electrolito iónico y como
disolvente y trabajan a temperaturas en torno a los 170-200 º C. Utiliza Pt
como catalizador para el ánodo, donde se sigue empleando hidrógeno como
reactivo, aunque en el cátodo se usa Pt-Co-Cr como catalizador. Se han
llegado a alcanzar potencias de 0.2 W cm-2 y eficiencias en torno al 40-50%,
con un tiempo de vida largo (hasta 40000 horas).
• Pilas de combustible de membrana de intercambio protónico (PEMFC):
Utilizan una membrana sólida, fabricada con un polímero capaz de conducir
protones (el cual constituye el electrolito sólido), intercalada entre dos
electrodos de platino porosos que permiten la difusión del hidrógeno y del
oxígeno. Entre todas las membranas fabricadas para este tipo de pila de
Capítulo 1: Síntesis
6
combustible destacan las de Nafion, permitiendo alcanzar potencias de hasta
0.7 W cm-2, con eficiencias y tiempo de vida similares a las AFC.
• Pilas de combustible de metanol directa (DMFC): Usan metanol en lugar de
hidrógeno como reactivo en el ánodo. Se han fabricado DMFC con ácido
sulfúrico como electrolito soporte empleando ánodos de metales nobles como
Pt, Ru, Pd o combinación entre ellos. Además de la lenta cinética de
electrodo, un problema a solventar en esta pila de combustible es el conocido
como crossover del metanol, que pasa del ánodo al cátodo a través de la
membrana. Al igual que las PEMFC, se han preparado DMFC con
membranas poliméricas como el Nafion, llegando a obtener potencias de
alrededor de 0.2 W cm-2 con un tiempo de vida hasta 1000 horas y eficiencias
en torno al 30-35%.
• Pilas de combustible de carbonato fundido (MCFC): En estos dispositivos, la
reacción catódica consume oxígeno y dióxido de carbono produciendo
carbonatos, que son conducidos hacia el ánodo donde se une con el hidrógeno
para formar agua y dióxido de carbono, el cual retorna al compartimento
catódico. La temperatura operativa es muy elevada, 650ºC, favoreciendo
sobrepotenciales más bajos para el inicio de las reacciones de la pila de
combustible y la no necesidad de metales muy nobles. La eficiencia y tiempo
de vida es similar al de las pilas PEMFC y AFC, mientras que la potencia es
de 0.12 W cm-2.
• Pilas de combustible de óxido sólido (SOFC): Estas pilas de combustible
utilizan una tecnología diferente con un sistema de cátodos y ánodos porosos
de lantano dopados con cationes divalentes y un electrolito formado por
óxidos de ytrio y zirconio. Para asegurar buenas conductividades iónicas y
electrónicas, se necesitan temperaturas muy elevadas (entre 800 y 1000ºC). El
combustible es hidrógeno, la potencia obtenida puede llegar a ser hasta de 1.2
W cm-2, la eficiencia está en torno al 50% y el tiempo de vida alcanza las
10000 horas.
Introducción
7
Además de las anteriores pilas de combustible, se han desarrollado otros prototipos
no comercializados, como por ejemplo la pila de combustible de etanol directa (DEFC)
[19] similar a las DMFCs, pero con algunas ventajas como su mayor densidad energética,
su nula toxicidad y su casi inexistente crossover a través de la membrana comparándolo
con el metanol [20]. Sin embargo, todavía presentan el inconveniente de que su potencia
está lejos de la de las pilas de hidrógeno. Por otra parte, se han propuesto otras alternativas
como combustible, como es el caso de ácido fórmico [21], compuestos nitrogenados como
amoníaco [22] o hidracina [23], hidruros metálicos como el borohidruro [24] o pilas de
combustible que utilizan catalizadores como enzimas o bacterias [25, 26].
Actualmente, para el desarrollo de nuevas pilas de combustible, los estudios
fundamentales de oxidación de pequeñas moléculas orgánicas en diferentes catalizadores
son interesantes de cara a su uso como reacción anódica, especialmente con alcoholes de
hasta 3 átomos de carbono como el glicerol. De manera análoga, se llevan a cabo
investigaciones similares para la reducción de oxígeno, la reacción catódica más común en
las pilas de combustibles. Estos estudios se hacen prestando atención a diferentes
parámetros como el pH del medio, la temperatura de trabajo o el catalizador utilizado. En
la presente tesis, se aborda el estudio de catalizadores para la oxidación de ácido fórmico y,
especialmente, para el etanol, de interés medioambiental debido a la posibilidad de
producirlo a partir de la fermentación de azúcares.
Un catalizador modifica la velocidad de una reacción química sin consumirse durante
el proceso. Si ese catalizador se utiliza en el cátodo o en el ánodo de una pila de
combustible, contribuye a acelerar la correspondiente reacción electródica. El electrodo
actúa como sustrato para facilitar la transformación electroquímica, lo que se conoce como
electrocatalizador [2], que permite aumentar la velocidad de reacción manteniendo la
diferencia de potencial aplicada en la interfase, el denominado sobrepotencial. Con
respecto a los tradicionales catalizadores químicos, la electrocatálisis tiene lugar a
temperaturas operativas más bajas, siendo el potencial el responsable de incidir en la
energía de activación necesaria para el inicio de las reacciones electroquímicas.
Desde mediados del siglo pasado existen numerosos estudios con diferentes metales
nobles buscando el mejor catalizador para la oxidación de pequeñas moléculas orgánicas.
Capítulo 1: Síntesis
8
Ejemplos claros de estos catalizadores para la oxidación de alcoholes son el oro, el platino,
el paladio y el rodio, generalmente usando electrolitos alcalinos, un ambiente menos
corrosivo y más favorable desde el punto de vista de la economía, ya que abre la
posibilidad del uso de materiales más baratos [27, 28]. Como ejemplo de la capacidad
electrocatalítica de varios metales nobles, se presenta la oxidación de n-butanol en medio
alcalino (Fig. 1.1) para los cuatro metales mencionados [29].
Fig. 1.1. Voltametría cíclica para la oxidación de 0.1 M n-butanol en 0.1 M NaOH a 25ºC y una
velocidad de barrido de 50 mV s-1 para diferentes electrodos metálicos: (a) Platino, (b) Oro, (c) Rodio y (d)
Paladio. Datos publicados de la ref. [28].
La mayor actividad total la presenta el oro, aunque los menores sobrepotenciales para
iniciar la oxidación del n-butanol se dan en el platino, lo cual es conveniente de cara a su
utilización en sistemas de generación de energía. El paladio se muestra menos activo que
los otros dos metales, mientras que el rodio apenas presenta actividad en estas condiciones.
A pesar de que el oro y el platino son catalizadores bastante activos en medio alcalino, sin
duda, el platino es el único metal noble que presenta actividades catalíticas importantes
Introducción
9
para la oxidación de casi todos estos compuestos a pHs ácidos [30]. Por ello, los estudios
electrocatalíticos, objeto de esta tesis, están enfocados en los electrodos de platino en
electrolitos con diferentes pHs, tratando de racionalizar los cambios en la reactividad de los
alcoholes al cambiar de medio ácido a medio básico.
Al oxidar moléculas orgánicas como el ácido fórmico, el metanol, el etanol o el
etilenglicol en platino, uno de los mayores problemas es el del envenenamiento del
catalizador producto del CO formado durante la oxidación [31], el cual bloquea la
superficie y retarda el potencial al cual se produce la oxidación de estas moléculas a CO2,
producto principal de la oxidación. En el caso de moléculas de más de un átomo de
carbono, se forman otros productos no deseados debido a la dificultad de romper el enlace
C-C, produciendo moléculas como el ácido acético [32], la cual es muy complicada de
oxidar. Todas estas reacciones electroquímicas, estudiadas en platino, son sensibles a la
estructura superficial del electrodo, es decir, dependiendo de cómo sea la orientación
cristalográfica de los átomos en el catalizador, la reactividad cambia, variando la cantidad
de CO producido y, por ende, la cantidad de CO2 total formado.
Para entender cómo afecta la estructura superficial en platino a la reactividad se
utilizan electrodos monocristalinos con superficies bien definidas preparados según el
método de Clavilier, el cual se explicará en la sección 1.3 de esta síntesis. Estas
investigaciones dan información fundamental muy interesante acerca de cómo varía la
relación entre los productos formados en la oxidación de pequeñas moléculas orgánicas en
función de la orientación cristalográfica de los electrodos. Sin embargo, desde un punto de
vista aplicado como el de las pilas de combustible, el coste de grandes catalizadores a
partir de superficies monocristalinas sería prohibitivo, lo que hace que su aplicación sea
inviable debido al alto coste del platino. Una manera de abaratar el coste del catalizador es
el del uso de nanopartículas, que optimizan el área activa usando la menor cantidad posible
de platino. Hay métodos desarrollados en la actualidad mediante los cuales se sintetizan
nanopartículas con tamaños entre 5 y 10 nm y en las cuales se puede controlar la estructura
superficial para que tenga preferencia por distintas formas, que indican la presencia de
diferentes estructuras superficiales [33, 34], encontrándose una buena relación entre la
reactividad de estas nanopartículas y la observada en superficies monocristalinas de
platino.
Capítulo 1: Síntesis
10
1.1.1 Oxidación de ácido fórmico en Pt
La oxidación del ácido fórmico es una reacción de gran interés, ya que sirve como
modelo para el estudio de oxidaciones similares con moléculas orgánicas más complejas, y
ha sido objeto de abundantes estudios en los últimos 50 años. De cara a su uso como
combustible, el ácido fórmico presenta como ventajas una cinética relativamente rápida,
una disminución en el ‘crossover’, comparándolo con otros alcoholes, o su baja
temperatura operativa, ventajas que compensan otros inconvenientes como su baja
densidad energética teórica (1.63 kW h kg-1) [21, 35]. La reacción global de la oxidación es
un proceso simple en el que se intercambian dos electrones:
(1.1)
Termodinámicamente, el potencial estándar de esta reacción es -0.25 V frente al electrodo
normal de hidrógeno (NHE, en sus siglas en inglés). No obstante, en platino, la reacción
necesita sobrepotenciales de hasta 0.6 V sobre el potencial termodinámico para el inicio de
la oxidación, debido a la producción de intermedios que bloquean los sitios activos del
platino y disminuyen su eficiencia, principalmente CO.
La oxidación del ácido fórmico en platino ocurre mediante un mecanismo dual hasta
el CO2 [36, 37] como se sugiere en el esquema:
(1.2)
siendo E1 < E2. En la ruta del intermedio venenoso, el CO se ha detectado como la especie
inhibidora mediante técnicas de IR [38, 39]. En este camino, el ácido fórmico descompone
espontáneamente sobre la superficie de platino:
(1.3)
Para oxidar el COads son necesarias especies OHads, que se originan a partir de moléculas
de agua [37]:
Introducción
11
(1.4)
Una vez formadas las especies OHads, se completa la oxidación hasta CO2:
(1.5)
En cuanto a la otra ruta, la naturaleza del intermedio activo no está tan clara.
Utilizando experimentos de IR en configuración de reflexión externa, se han propuesto
intermedios como –COOH [30] y, más recientemente, se ha detectado la presencia de
formiato (HCOOads), que se postula mayoritariamente como la especie activa previa al CO2
[36, 40]. Osawa et. al confirman con experimentos en configuración de ATR la presencia
de formiato con un enlace tipo ‘bridge’ a los átomos de platino [41-43], siendo el
mecanismo de oxidación propuesto el representado en el siguiente esquema:
(1.6)
(1.7)
Sin embargo, Behm et. al. sugieren que dicho anión formiato también puede
bloquear sitios activos del platino [44, 45], aconsejando una tercera vía en la oxidación del
ácido fórmico mediante la cual se produce directamente la oxidación hasta CO2. Además,
el pH del sistema también influye en la reactividad del sistema, aunque existen ciertas
discrepancias en cuanto a su efecto. Joo et. al. [46] proponen la importancia de la presencia
de aniones formiato en la disolución que provoca un aumento de la actividad hasta valores
de pH cercanos al pK del ácido fórmico (3.75), mientras que Brimaud et. al. [47] observan
un aumento de las actividades en un rango de pHs entre 0 y 7. Sin embargo, ambos
trabajos concuerdan en la importancia de la presencia de los aniones formiato para una
mejora en la actividad de la reacción.
Todas estas rutas son sensibles a la estructura superficial del platino [37, 48, 49],
mostrándose el Pt(100) como la superficie más activa pero a la vez más propensa a la
formación de CO, por lo que prácticamente siempre está inhibido. Sin embargo, el Pt(111),
que es menos activo, se envenena menos y consigue la oxidación completa mediante la
ruta del intermedio activo a potenciales más bajos. La Fig. 1.2 muestra las voltametrías
cíclicas características para estas superficies de platino:
Capítulo 1: Síntesis
12
Fig. 1.2. Voltametría cíclica para el primer ciclo en la oxidación de 0.1 M HCOOH + 0.5 M H2SO4
en: (a) Pt(111) y (b) Pt(100). Velocidad de barrido: 0.02 V s-1.
Para evitar la formación de CO y favorecer la actividad a bajos potenciales, una
opción es modificar la composición de la superficie de platino con algún átomo de
diferente naturaleza tanto sobre los planes base del platino como sobre superficies
escalonadas, por ejemplo Bi [50-52], Sb [53, 54], Pb [55], Pd [56], Te [57], Se [58], As
[59] o combinaciones de varios átomos [60]. La catálisis hasta la completa oxidación a
CO2 en estos electrodos modificados se explica a través de diferentes efectos: a) efectos de
tercer cuerpo, donde los adátomos bloquean varios sitios activos contiguos, necesarios para
la formación del CO, b) efectos electrónicos, donde la presencia del adátomo disminuye la
energía de activación entre el adsorbato y el sustrato facilitando la oxidación del CO o
favoreciendo la ruta a través del intermedio activo o c) por un mecanismo bifuncional,
donde las especies dadoras de oxígeno están presentes a potenciales más bajos en el
electrodo modificado, produciendo una disminución del sobrepotencial necesario para la
oxidación del CO respecto a los electrodos de platino sin modificar.
0
5
10
15
20
0.0 0.2 0.4 0.6 0.8 1.0
0
1
2
j/mA
cm-2
Pt (111)(b)
(a)
E vs RHE/V
Pt (100)
Introducción
13
1.1.2 Oxidación de etanol en Pt
Al igual que el ácido fórmico, el estudio de la electrooxidación de etanol en platino
ha recibido mucha atención, debido a su facilidad para el almacenamiento y sus beneficios
medioambientales, comentados anteriormente. Además, comparando con otros alcoholes
como el metanol, presenta ventajas adicionales, como su mayor densidad energética teórica
(8.00 kW h kg-1 frente a 6.10 kW h kg-1) y su menor toxicidad. En la reacción para la
completa oxidación del etanol, se intercambian 12 e-:
(1.8)
El potencial termodinámico para la oxidación del etanol es 0.085 V vs NHE, pero, al igual
que el ácido fórmico, la reacción cinéticamente es más lenta, necesita mayores
sobrepotenciales para llevarse a cabo, debido al CO que bloquea los sitios activos, y
además forma productos no deseados como el ácido acético.
El mecanismo de oxidación en platino es más complejo que el del ácido fórmico, ya
que requiere que se rompa el enlace C-C antes de llegar a la oxidación completa [61, 62]:
(1.9)
En este mecanismo se consideran dos rutas principales, la de la formación de ácido
acético y la deseada hasta CO2. A pesar de que ambos caminos son termodinámicamente
favorables, la formación de ácido acético es mayoritaria respecto a la formación de CO2,
debido a que la energía de activación requerida para que se produzca la rotura del enlace
C-C es muy elevada [63]. En medio ácido, la ruta de formación de ácido acético, con
únicamente 4 e- producidos por molécula, es considerada no deseada ya que es un producto
estable casi imposible de oxidar hasta CO2 a temperatura ambiente [64]. Además de ácido
acético, se detecta la formación de acetaldehído, también característico de la ruta
incompleta de oxidación de etanol [65]. El acetaldehído se genera mediante una adsorción
disociativa del etanol [29]:
(1.10)
Capítulo 1: Síntesis
14
(1.11)
Posteriormente, dicho acetaldehído se adsorbe en la superficie de platino formando la
denominada especie acetil adsorbida [66], que, con la ayuda de OHads procedentes de
moléculas de H2O formados de la misma manera que en la reacción (1.4), producen el
ácido acético a potenciales alrededor de 0.6 V:
(1.12)
(1.13)
Recapitulando, en la ruta de la oxidación incompleta se produce ácido acético como
producto final, intercambiando 4 e- en su reacción global:
(1.14)
La oxidación completa de etanol, que implica la rotura del enlace C-C, se produce
también a partir de la especie acetil adsorbida formada en la reacción (1.12), la cual disocia
a bajos potenciales [66, 67]:
(1.15)
Para los fragmentos (CHx)ads, el valor de x será 2 o 3 dependiendo de si el enlace con el Pt
es de tipo linear o tipo ‘bridge’. Dichos fragmentos forman metano entre 0.1 V y 0.4 V,
como se ha podido detectar mediante experimentos de espectrometría de masas diferencial
electroquímica (DEMS, en sus siglas en inglés) [65]:
(1.16)
Además, esos mismos fragmentos (CHx)ads pueden producir CO a potenciales superiores a
0.4 V [68], de acuerdo con la reacción:
(1.17)
Dicho (CO)ads, junto al formado en la reacción (1.15), reaccionará con OHads a
potenciales más altos de 0.6 V para formar CO2 mediante un mecanismo Langmuir-
Hinshelwood, de igual manera que en la reacción (1.5).
En cuanto a la influencia de la estructura superficial del platino, al igual que en la
oxidación de ácido fórmico, en medio ácido las superficies de Pt(100) favorecen la
Introducción
15
formación de CO mientras que en los dominios 111 únicamente se produce la oxidación
incompleta hasta ácido acético [69-72]. Además, en esta superficie, el anión acetato
adsorbido a partir de la ruta de formación de ácido acético inhibe la reacción de oxidación
[73]. El Pt(110) muestra un comportamiento intermedio entre el Pt(100) y el Pt(111), esto
es, produce la rotura del enlace C-C formando CO pero en menos proporción que el
Pt(100), además de grandes cantidades de ácido acético mediante la ruta de oxidación
incompleta. Los perfiles voltamétricos de los tres planos bases del platino para la oxidación
de etanol 0.2 M se muestran en la Fig. 1.3:
Fig. 1.3. Voltametría cíclica para la oxidación de 0.2 M CH3CH2OH + 0.5 M H2SO4 en los tres planos
base del platino. Velocidad de barrido: 0.02 V s-1.
Para mejorar la actividad hacia la oxidación completa de etanol, una opción clara es
la de utilizar superficies escalonadas, concretamente con largas terrazas 111 separadas
0.0
2.0
4.0
6.0
8.0
0.0
0.5
1.0
1.5
0.0 0.2 0.4 0.6 0.8 1.0-0.1
0.0
0.1
0.2
0.3
Pt (100)
j/mA
cm-2
Pt (110)
E vs RHE/V
Pt (111)
Capítulo 1: Síntesis
16
por escalones 110 o 100 [74-76], donde las moléculas de CO adsorbidas sobre los
sitios de escalón se oxidan hasta CO2 a potenciales más bajos, e incluso, en el caso de las
superficies con escalones 110, se produce una doble mejora para la electrooxidación de
etanol: a potenciales por debajo de 0.7 V, se cataliza la escisión del enlace C-C y su
oxidación hasta CO2, mientras que a altos potenciales se beneficia la formación de
acetaldehído y ácido acético. Por otra parte, al igual que en el ácido fórmico, la adsorción
de un átomo diferente sobre dichos sitios de escalón, puede beneficiar todavía más la
oxidación de etanol a potenciales más negativos [77, 78], favoreciendo la oxidación del
CO adsorbido a CO2 a bajos recubrimientos de adátomo, ya que a altos recubrimientos se
inhibe la rotura del enlace C-C produciendo únicamente el ácido acético, no deseado.
La decoración de las superficies de platino con un átomo diferente persigue un doble
efecto [79]: (1) mejorar la fracción de moléculas de etanol en las que se produce la escisión
del enlace C-C, como es el caso del rodio [80] y (2) favorecer la oxidación del CO hasta
CO2, como ocurre por ejemplo con el rutenio, el estaño o el paladio, apoyando la adsorción
del OH [81]. Partiendo de la formación de la especie acetil en la reacción (1.12), el
mecanismo de oxidación de etanol se beneficia de la presencia de otros átomos para
alcanzar la formación de CO2:
(1.18)
(1.19)
(1.20)
(1.21)
Además del estaño o el rutenio, la adición de otros átomos como el osmio, iridio o
wolframio parecen ejercer un efecto similar de optimizar la cantidad de CO2 formado en la
oxidación de etanol [82-84].
En medio alcalino, el mecanismo es diferente y menos estudiado en la bibliografía,
pero se ha propuesto que la adsorción del etanol en el platino ocurre a través del oxígeno y
no a través del C1 [85, 86], formando especies etoxi adsorbidas sobre el platino:
(1.22)
Introducción
17
A partir de este intermedio, sin producirse la rotura del enlace C-C, se originan
acetaldehído y aniones acetato, especie mayoritaria y casi exclusiva para la oxidación de
etanol en este medio independientemente de la estructura superficial del platino,
proponiéndose distintos mecanismos para su formación:
• La especie etoxi es la única adsorbida a pHs elevados [85], oxidándose a
acetaldehído según la reacción:
(1.23)
El acetaldehído se transforma en acetato con la ayuda de un OHads, siguiendo
un mecanismo Eley-Rideal:
(1.24)
• Partiendo de la misma especie etoxi, ésta se oxida sucesivamente hasta
producir acetato adsorbido sobre el electrodo [86]:
(1.25)
(1.26)
De acuerdo con estas reacciones, de la desorción de las especies adsorbidas
formadas en las reacciones (1.25) y (1.26) se producirán acetaldehído y
acetato respectivamente:
(1.27)
(1.28)
Capítulo 1: Síntesis
18
1.2 Técnicas experimentales
Durante la tesis doctoral se emplearon diversas técnicas experimentales con el
objetivo de obtener la mayor información posible acerca de las oxidaciones de etanol y
ácido fórmico. Las técnicas electroquímicas permiten adquirir de una forma rápida
información acerca de la dependencia con el potencial de las reacciones electroquímicas
estudiadas. Para obtener detalles acerca de la naturaleza de los adsorbatos formados
durante las oxidaciones se hizo uso de la espectroscopía infrarroja in situ de reflexión
externa en configuración de capa fina.
Además, se utilizó la técnica de espectroscopía infrarroja de reflexión interna
acoplada con la espectrometría de masas, la cual permite simultáneamente averiguar las
especies formadas en un proceso electroquímico mediante experimentos IR junto a
información cuantitativa del mecanismo de reacción con la espectrometría de masas.
1.2.1 Técnicas electroquímicas
Las técnicas electroquímicas manejadas durante esta tesis doctoral son,
principalmente, la voltametría cíclica y la cronoamperometría, las cuales permiten una
caracterización superficial de los electrodos empleados y, posteriormente, el estudio de
parámetros acerca de su reactividad electroquímica.
Antes de comenzar con la descripción de las técnicas, para realizar estos
experimentos se siguió un protocolo experimental común para una celda de tres electrodos:
Técnicas experimentales
19
Fig. 1.4. Disposición experimental utilizada durante los experimentos con técnicas electroquímicas
(CE: Contraelectrodo, RE: Electrodo de referencia, WE: Electrodo de trabajo). Esquema adaptado de la ref.
[87].
En esta disposición, el generador de funciones crea un programa de potenciales que
se aplica entre el electrodo de trabajo y el de referencia a través del potenciostato,
modificando la corriente que circula a través del electrodo de trabajo y el contraelectrodo
para mantener el potencial deseado entre el electrodo de trabajo y el electrodo de
referencia. La corriente registrada es la variable, que mide la velocidad de respuesta a la
perturbación de potencial producida en las técnicas electroquímicas. Como contraelectrodo
se usa un hilo de Pt, el electrodo de referencia es un hilo de negro de Pt en contacto con la
misma disolución de trabajo al cual se burbujea hidrógeno y, finalmente, como electrodo
de trabajo se utiliza la superficie de platino objeto de estudio, ya sea una superficie
monocristalina o nanopartículas depositadas en un sustrato conductor.
La voltametría cíclica [87, 88] es la técnica más popular para estudios iniciales en un
sistema con especies redox. En ella se puede obtener información sobre procesos
electródicos complicados. Es una técnica no estacionaria, que consiste en realizar un
barrido de potenciales a una determinada velocidad de barrido entre un potencial inferior y
un potencial superior, registrando al mismo tiempo la corriente obtenida. En los resultados
se presentan las curvas E-i, representaciones conocidas como voltamogramas o
voltamperogramas. En la Fig. 1.5 se muestra un ejemplo de un voltamograma para un
electrodo de platino poliorientado utilizando como electrolito soporte 0.5 M H2SO4:
Capítulo 1: Síntesis
20
Fig. 1.5. Programa de barrido de potenciales y corriente obtenida frente al tiempo (izqda.) y
representación común de i vs E (dcha.) en una voltametría cíclica. Sistema test: Electrodo Pt poly en 0.5 M
H2SO4.
El empleo de esta técnica en experiencias electroquímicas es extenso, tanto para
caracterizar la superficie de los electrodos monocristalinos de Pt a partir de los picos de
adsorción de hidrógeno como para detectar la presencia de posibles impurezas. Las
corrientes de pico proporcionan información acerca de la naturaleza de la reacción
electroquímica. Modificando las velocidades de barrido se puede conocer si el proceso está
controlado por la transferencia de carga de especies adsorbidas en el electrodo o si, por el
contrario, el proceso viene marcado por la difusión de especies electroactivas procedentes
de la disolución hacia el electrodo. Concretamente, las relaciones entre las corrientes de
pico (ip) y la velocidad de barrido (v) son ip ∝ v para el caso de procesos con especies
adsorbidas involucradas e ip ∝ v1/2 en casos donde intervienen especies en disolución.
Además, la diferencia entre los potenciales de pico en el barrido positivo y en el barrido
negativo de una voltametría cíclica da una idea acerca de la reversibilidad del sistema.
0.2
0.4
0.6
0.8
0 5 10 15 20 25 30
-20
-10
0
10
20
0.0 0.2 0.4 0.6 0.8
-20
-10
0
10
20
E/
V
i/µA
t/s
i/µA
E/V
Técnicas experimentales
21
La cronoamperometría [87, 89] es una técnica en el que se aplica un salto entre un
potencial donde no hay reacción faradaica hasta un potencial donde se produce la
reducción/oxidación estudiada. Es más sencilla que la voltametría cíclica, ya que mantiene
el potencial constante. Se mide la corriente producida y su evolución con el tiempo:
Fig. 1.6. Representación de un salto de potencial entre 0.1 V y 0.7 V frente al tiempo (izqda.), además
de las corrientes registradas durante ese salto. Sistema test: Electrodo Pt(111) en 0.2 M CH3CH2OH + 0.1 M
NaOH.
Al realizar el salto, la corriente crece instantáneamente debido al gradiente de
concentración creado, que produce un flujo continuo de especie electroactiva hacia el
electrodo. Para un electrodo plano, la disminución de la corriente transitoria con el tiempo
refleja generalmente problemas de difusión del reactivo hacia el electrodo, o bien que la
adsorción de alguna especie bloquea la reacción de estudio. La cronoamperometría es útil
para aclarar aspectos mecanísticos de una reacción, ajustando los datos con un modelo
cinético, como en el caso del CO en electrodos de Pt [90, 91], o simplemente para ver si el
efecto electrocatalítico se mantiene estable con el tiempo [92, 93].
Las medidas se han realizado con un generador de funciones (EG&G PARC 175)
junto a un potenciostato (eDAQ 161 o AMEL Model 2053) y un registrador (eDAQ
ED401), o directamente con un µAutolab type III. El potenciostato AMEL Model 2053 se
utiliza en el caso de que hayan sido necesarias correcciones de caída óhmica,
0 200 400 600 800 10000.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0 200 400 600 800 1000-0.15-0.10-0.050.000.050.100.150.200.250.30
E/V
t/s
i/mA
t/s
Capítulo 1: Síntesis
22
principalmente al trabajar con electrodos de platino para la oxidación de etanol en medio
alcalino, debido a las altas corrientes registradas y a la menor conductividad en este tipo de
disoluciones. El potencial real aplicado en la interfase de estudio función del potencial
impuesto por el potenciostato viene dado por la expresión:
𝐸𝑟𝑒𝑎𝑙 = 𝐸𝑎𝑝𝑙𝑖𝑐𝑎𝑑𝑜 − 𝑖𝑅 (1.29)
donde i es la corriente medida y R se refiere a la resistencia del sistema, que en la célula
empleada se atribuye principalmente a la disolución. El objetivo de la corrección de la
caída óhmica es que el potencial real sea igual al potencial aplicado, por lo que el término
iR de la ecuación (1.29) debe ser anulado. Para ello, el potenciostato aplica una resistencia
externa calibrada previamente que en todo momento compensa ese término. La calibración
de esta resistencia se realiza estableciendo ciclos a altas velocidades de barrido en zona de
doble capa, aplicando resistencias crecientes hasta comprobar que el perfil voltamétrico
recupera la forma capacitiva característica de esa zona.
1.2.2 Espectroscopía infrarroja (IR) in situ
La espectroscopía IR se puede utilizar como técnica complementaria a las
experiencias de voltametría cíclica y cronoamperometría, proporcionando datos que
ayudan a la identificación de las especies formadas, consumidas o adsorbidas en la
superficie del electrodo conforme se varía el campo eléctrico de la doble capa, además de
proveer información sobre su geometría de adsorción [94-96]. Para ello, un sistema
electroquímico como el expuesto en la Fig. 1.4 se acopla con un espectrómetro IR,
conformando el sistema para la realización de experiencias espectroelectroquímicas.
Para realizar los espectros IR, se emplea un espectrómetro de FTIR acoplado con un
interferómetro de Michelson [97, 98], por el cual circula un haz IR policromático cuya
intensidad disminuye al pasar a través de la muestra debido a la radiación absorbida. El
interferómetro de Michelson está compuesto por dos espejos, uno fijo y otro móvil en la
dirección del haz de luz. Entre los dos espejos se sitúa un divisor de haz, donde la
radiación es parcialmente reflejada al espejo móvil y parcialmente transmitida al espejo
Técnicas experimentales
23
fijo. Ambas partes del haz regresan al divisor recorriendo diferentes caminos ópticos,
originando una interferencia. A la representación entre ese retraso óptico medido por el
interferómetro de Michelson con la intensidad de la radiación alcanzada se le denomina
interferograma. La transformación de los interferogramas en espectros se logra mediante
una operación matemática denominada transformada de Fourier (FT, en sus siglas en
inglés). La principal ventaja de los espectrómetros que utilizan transformada de Fourier es
la velocidad con la que obtienen un interferograma, ya que son capaces de medir todas las
longitudes de onda del haz de luz simultáneamente, al contrario que otros espectrómetros
denominados dispersivos, que las miden consecutivamente.
La configuración empleada para la realización de los espectros con monocristales de
platino o el soporte de oro en el cual se depositan las nanopartículas de platino es la de
reflexión externa, IRRAS (siglas en inglés de espectroscopía infrarroja de reflexión-
absorción), en la que se analiza la intensidad de la radiación en función de la longitud de
onda de un haz de luz que es reflejado en un metal en contacto con una disolución. Una
característica de las experiencias IRRAS es la del obligado cumplimiento de la regla de
selección superficial [99], esto es, solamente los modos de vibración que posean una
componente del momento dipolar perpendicular a la superficie metálica interactúan con el
campo eléctrico de la radiación IR. De acuerdo a este principio, la luz polarizada s
(perpendicular al plano de reflexión) únicamente se muestra activa para especies presentes
en disolución, mientras que la luz polarizada p (paralelo al plano de reflexión), además de
las especies presentes en disolución, presenta contribuciones de modos vibracionales con
cambios en el momento dipolar perpendicular a la superficie de las especies adsorbidas en
superficie.
En el modo de reflexión externa, el electrodo monocristalino se pone en contacto con
un prisma transparente a la radiación IR y con un bajo índice de refracción, procurando que
el espesor de la capa de disolución sea el mínimo posible, para minimizar los efectos de
absorción IR por la disolución. En la Fig. 1.7 se muestra el prisma acoplado por una junta
de teflón a una célula electroquímica similar a la empleada en las experiencias de
voltametría cíclica y cronoamperometría. La pequeña porción de disolución confinada
entre el electrodo y el prisma conforman la estructura de capa fina con un espesor entre 1 y
10 µm.
Capítulo 1: Síntesis
24
Fig. 1.7. Configuración de la célula electroquímica y del prisma de CaF2 durante los experimentos de
IRRAS con los electrodos monocristalinos de Pt.
A pesar de que el espesor de la capa de difusión es pequeño, las principales bandas
observadas en el espectro pertenecen al disolvente, que en todos los casos presentados en
esta tesis es agua. La Fig. 1.8 muestra el espectro ‘Single Beam’ habitual obtenido en cada
experiencia IRRAS con electrodos de platino. En ella, se ven modos de vibración
característicos de los enlaces O-H del agua como las tensiones simétrica y asimétrica por
encima de 3500 cm-1 y la flexión simétrica sobre 1600 cm-1.
Fig. 1.8. Forma general de un espectro ‘Single Beam’ para una configuración de capa fina en un
electrodo de platino monocristalino acoplado con un prisma de CaF2.
4000 3500 3000 2500 2000 1500 1000 500 00
20
40
Flexión simétrica O-H
Abso
rban
cia/u
.a.
υ/cm-1
OH H
OH H
Tensiones simétricay asimétrica O-H
OH H
Técnicas experimentales
25
Al tomar varios espectros a diferentes potenciales, éstos son aparentemente iguales,
ya que la contribución de las moléculas adsorbidas a la radiación IR es muy pequeña
comparada con la del disolvente, produciéndose variaciones de menos de 0.01 unidades de
absorbancia. Para eliminar en la medida de lo posible la contribución del disolvente y
centrarse en las especies adsorbidas sobre el electrodo y en los productos formados, la
estrategia seguida consiste en tomar varios espectros a diferentes potenciales y en un corto
espacio de tiempo, utilizando uno de ellos como referencia y observando sus variaciones al
modificar el potencial. Los espectros resultantes se presentan en términos de unidades de
absorbancia 𝐴 = −log (𝑅/𝑅0), donde 𝑅 y 𝑅0 son los valores de intensidad de la luz
reflejada al potencial de trabajo y al de referencia respectivamente. Para las pequeñas
variaciones esperadas en estos valores, se considera que 𝐴 = −(𝑅 − 𝑅0)/ 𝑅0. Los
espectros se realizan siguiendo el esquema de la Fig. 1.9, que muestra un ejemplo para el
caso de la oxidación de CO adsorbido en un electrodo de Pt(111) en 0.5 M H2SO4.
Fig. 1.9. Esquema con los pasos seguidos a la hora de realizar espectros: (a) modo de adquisición de
espectros a un potencial estático, (b) espectros ‘Single Beam’ medidos a diferentes potenciales y (c) espectros
procesados utilizando como referencia el espectro a 0.1 V (azul) y a 0.9 V (verde) para la oxidación de CO
con Pt(111) en una disolución 0.5 M H2SO4.
2400 2200 2000 1800
2400 2200 2000 1800 1600 1400 1200
Potencial E2(10 interferogramas)
Potencial E1(10 interferogramas)
δ (re
traso
ópt
ico)
a)
E2
E/V
t/s
E1
∆t
COBCOL
Referencia 0.1 V Referencia 0.9 V
0.1 V
0.4 V
0.9 V
υ/cm-1
0.4 V
0.004 u.a.
c) CO2
υ/cm-1
0.1 V 0.9 V
3 u.a.
b)
Capítulo 1: Síntesis
26
El potencial deseado se establece manualmente, potencial en el cual se miden un
número fijo de interferogramas, que en el caso del ejemplo presentado en la Fig. 1.9a son
10. El espectro ‘Single Beam’ resultante se adquiere del promedio de todos los
interferogramas obtenidos. Cuanto más alto sea el número de interferogramas tomados,
mejor relación señal/ruido se logrará. Por ello, en todos los espectros realizados durante
esta tesis se toman, al menos, 100 interferogramas. El Δt indicado en el esquema se
corresponde con el tiempo que se necesita para medir los interferogramas, que para el caso
en que se tomen 100 es de 43 segundos.
Los espectros ‘Single Beam’ de la Fig. 1.9b muestran la diferencia inapreciable entre
las medidas tomadas a diferentes potenciales. La Fig. 1.9c expone los espectros resultantes
después de restarlos con los espectros a los potenciales de referencia escogidos (0.1 V o
0.9 V). Las bandas positivas indican la presencia de una especie respecto al potencial de
referencia, como es el caso de las bandas de CO lineal sobre 2050 cm-1 en los dos
potenciales calculados con el referencia a 0.9 V. Las bandas negativas se refieren a
especies consumidas respecto al potencial de referencia, como las bandas de CO2 a 2340
cm-1 en el mismo caso del ejemplo con el referencia a 0.9 V o en la banda de CO lineal en
el espectro a 0.9 V utilizando el referencia a 0.1 V. En el caso en el que aparecen bandas
bipolares, éstas se refieren a especies adsorbidas que están presentes tanto en el potencial
de referencia como en el potencial estudiado. Como la frecuencia de la banda se ve
afectada por el potencial de trabajo, la diferencia con el espectro de referencia da lugar a
una banda bipolar, como en el mostrado en la banda de CO lineal del espectro a 0.4 V, con
el referencia establecido a 0.1 V.
Los espectros FT-IRRAS se han adquirido utilizando espectrómetros Nicolet Nexus
(modelo 8700) o Nicolet Magna modelo 850, especificando el espectrómetro empleado en
cada capítulo. En ambos casos, un detector MCT (Telururo de Mercurio y Cadmio) se
acopla al espectrómetro, que además está dotado de un sistema Veemax de Spectra-Tech
como sistema de reflectancia especular. Como ventana óptica, en todos los experimentos
de reflexión externa se ha utilizado un prisma de CaF2, que es capaz de detectar bandas por
encima de 900 cm-1 [95], suficiente para los casos estudiados. El prisma fue biselado a 60º,
lo cual provoca un ángulo de incidencia con el electrodo de trabajo de alrededor de 70º,
cercano al ángulo crítico del material que se encuentra sobre 77º. Cuanto más cercano esté
Técnicas experimentales
27
el ángulo de incidencia al ángulo límite del material, mejor relación entre las intensidades
de la luz reflejada ((𝑅 − 𝑅0)/ 𝑅0) se obtendrá y, por tanto, mejor señal de absorbancia
[100].
Para asignar las bandas de los espectros, los resultados se comparan con espectros de
transmisión realizados con posibles productos o intermedios de las reacciones de oxidación
estudiadas. Dichos espectros de transmisión se tomaron con un prisma de ZnSe, el cual
puede mostrar modos de vibración que aparezcan a partir de 500 cm-1. La resolución de los
espectros fue de 8 cm-1 empleando luz polarizada p en la toma de los espectros.
1.2.3 Espectroscopía infrarroja ATR acoplada con espectrometría de masas
DEMS
A pesar de las ventajas de la técnica IRRAS, existen también algunas limitaciones al
trabajar con esta configuración. En primer lugar, a pesar de que la capa de disolución entre
el electrodo y el prisma de CaF2 es de un espesor muy pequeño (entre 1 y 10 µm), la
absorción de la radiación IR por parte de la disolución es mucho mayor comparándola con
la de la capa de adsorbatos (suponiendo que la capa de adsorbato fuera de 1 nm, la
absorción por parte de la disolución sería entre 3 y 4 órdenes de magnitud mayor). Por ello,
es importante reducir la absorción IR de fondo en los espectros, la cual se asigna al
disolvente. Por otra parte, los problemas de difusión de especies en la configuración de
capa fina provocan que, en el caso de que los productos de la reacción sean gases, éstos
queden atrapados dentro de la capa de disolución entre el electrodo y el prisma,
provocando impedimentos en las medidas espectrales y electroquímicas. De acuerdo con
estos hechos, la configuración FT-IRRAS no se considera como la más adecuada para el
estudio de reacciones rápidas en superficie.
Los problemas anteriores pueden solucionarse con la configuración de reflexión
interna o ATR (reflexión total atenuada en sus siglas en inglés) [101, 102]. Sobre un
prisma transparente para el infrarrojo y con un índice de refracción suficientemente alto
como para permitir la reflexión total, por ejemplo silicio o germanio, se deposita una fina
Capítulo 1: Síntesis
28
película de un metal que se usa como
electrodo de trabajo, constituyendo la
denominada configuración de
Kretschmann que viene representada
en la Fig. 1.10. La radiación IR se
focaliza directamente sobre el prisma
alcanzando la película de metal y
formando una onda evanescente que
penetra solo unos cientos de
nanómetros sobre la muestra, lo cual
permite que la aportación de las bandas
IR procedentes de la disolución sea reducida considerablemente respecto a lo observado en
la configuración FT-IRRAS. Además, si la película presenta rugosidades de hasta 10 nm se
produce una intensificación de la señal conocida como SEIRAS, que es capaz de producir
un aumento de hasta 1000 órdenes de magnitud en la intensidad de la señal [103].
Por otro lado, la espectrometría de masas diferencial electroquímica (DEMS) [104,
105] permite la rápida detección de productos gaseosos volátiles formados en reacciones
electroquímicas. La instrumentación consiste básicamente en una célula electroquímica,
donde está ubicado el electrodo de trabajo, una membrana de teflón y un sistema de vacío
donde se incluye el espectrómetro de masas:
Fig. 1.11. Dispositivo convencional para experimentos DEMS, tomado de la ref. [106].
Fig. 1.10. Dispositivo experimental para experimentos de ATR-
SEIRAS utilizando la configuración de Kretschmann.
Técnicas experimentales
29
Es conveniente que la célula electroquímica sea de un material como el vidrio,
diferente al teflón, cuya porosidad puede provocar la absorción de especies orgánicas. Su
función es la de controlar las condiciones electroquímicas sobre el electrodo de trabajo,
permitiendo el transporte de los productos gaseosos volátiles hacia la membrana de teflón.
El carácter hidrofóbico de este material impide el paso del electrolito hacia el sistema de
vacío, mientras que sí es permeable a gases volátiles y relativamente no polares, que son
conducidos hacia el espectrómetro de masas, el cual necesita condiciones de alto vacío (<
10-5 mbar) para su correcto funcionamiento, condiciones obtenidas con la ayuda de dos
bombas de vacío.
En un experimento DEMS típico, al mismo tiempo que se mide la corriente faradaica
realizando una voltametría cíclica normal, se registran las corrientes correspondientes a las
masas que contengan información acerca de los iones que se desean detectar. El registro de
estas corrientes frente al potencial se conoce como voltametría cíclica de espectrometría de
masas (MSCV en sus siglas en inglés). Las aplicaciones de esta técnica son variadas, como
la caracterización de adsorbatos orgánicos, la detección de especies nitrogenadas, la
evolución de hidrógeno en una reacción tan complicada como la oxidación de
formaldehído o, la aplicación más interesante desde nuestro punto de vista, el seguimiento
de las reacciones de oxidación de pequeñas moléculas orgánicas como el ácido fórmico o
el etanol.
La principal ventaja de las técnicas DEMS respecto a técnicas ATR es la posibilidad
de detectar especies inactivas en el IR, como la formación de hidrógeno. Sin embargo, el
DEMS está más limitado ya que solamente es capaz de medir productos gaseosos volátiles,
mientras que el ATR permite medir intermedios de reacción adsorbidos sobre el electrodo
de trabajo y productos no volátiles. Por ello, las técnicas de ATR y DEMS se consideran
complementarias, y su combinación es de mucha utilidad para estudios de electrocatálisis
como los realizados en esta tesis. Además, si se acopla con una célula de flujo
electroquímica de doble capa fina, la cual trabaja en condiciones de transporte de masa, se
obtiene información acerca de la cinética de las reacciones ocurridas en el electrodo [107].
Capítulo 1: Síntesis
30
Fig. 1.12. Diagrama esquemático de la célula de flujo de capa fina para medidas ATR-FTIRS y on-
line DEMS junto a una imagen con los wafers de Si acoplados con el prisma (ver texto para más detalles). In-
1 e In-2: puntos de entrada del electrolito; CE-1 y CE-2: puntos de conexión de los dos contraelectrodos; WE
y RE: puntos donde se conectan el electrodo de trabajo y de referencia; Out: punto de salida del electrolito.
Esquema adaptado de la ref. [107].
La Fig. 1.12 muestra un esquema orientativo del dispositivo experimental usado en
los experimentos ATR-FTIR acoplados con DEMS. El electrodo de trabajo es un ‘wafer’
con el depósito de nanopartículas acoplado con el prisma semicilíndrico de silicio. El
‘wafer’ de silicio consiste en una pieza rectangular a la cual se le deposita una película de
Au mediante la técnica de ‘electroless’ [108], sobre la cual se deposita la muestra de
nanopartículas de platino. El principal requisito que tiene que cumplir es ser lo
suficientemente fino como para permitir el paso del haz IR que viene a través del prisma y,
a su vez, suficientemente grueso para proporcionar una conductividad adecuada. El
conjunto del prisma y el wafer son presionados sobre la célula espectroelectroquímica
mediante una junta circular de Parafilm® y una hoja fina circular de cobre que se emplea
para hacer contacto.
La célula espectroelectroquímica está fabricada con Kel-F® y presenta dos
compartimentos diferentes: en el primero, la disolución llega hasta el conjunto del
electrodo de trabajo en el centro de la celda, que está rodeada por seis pequeños capilares
por los cuales fluye la disolución en dirección al segundo compartimento, permitiendo un
Técnicas experimentales
31
flujo laminar continuo hacia el electrodo de trabajo. El volumen aproximado de la célula es
de 10 µL. En el segundo compartimento de la célula, el electrolito es conducido hacia la
membrana porosa de teflón antes de llegar al punto de salida de la disolución. Como se ha
explicado, la membrana permite el paso de los gases volátiles formados en las
nanopartículas de platino y los conduce hacia el espectrómetro de masas. El retraso entre la
señal de corriente faradaica y la respuesta del espectrómetro de masas es de alrededor de 1
s, que es el tiempo que tarda el electrolito en fluir desde el primer al segundo
compartimento de la célula espectroelectroquímica.
Como electrodo de referencia se usa un electrodo saturado de calomelanos (SCE, en
sus siglas en inglés), aunque los resultados están corregidos y presentados respecto al
electrodo reversible de hidrógeno (RHE, en sus siglas en inglés) para una comparación más
cómoda con los demás resultados de la tesis. Además, en el sistema se introducen dos
contraelectrodos de platino en la entrada y la salida de la célula de flujo, con el objetivo de
favorecer una distribución más homogénea del campo eléctrico en las células de flujo de
capa fina.
En estas experiencias se registran simultáneamente la voltametría cíclica, los
espectros y la voltametría cíclica de espectroscopía de masas de una manera
potenciodinámica con un barrido de potencial a una velocidad lenta de 5 mVs-1. El
potenciostato utilizado fue un ‘Pine instruments potentiostat’, mientras que el registro de
datos fue computerizado. Los experimentos in-situ ATR-FTIRS fueron llevados a cabo en
un espectrómetro BioRad FTS-6000 equipado con un accesorio de reflexión no comercial
con un ángulo de incidencia del haz IR de 70º y un detector de telururo de mercurio y
cadmio (MCT). Se toman espectros cada 10 s con una resolución de 4 cm-1 a la vez que se
realiza un barrido de potenciales, aunque los espectros ATR presentados se midieron de
manera potenciostática para mejorar la relación señal/ruido. Los espectros se presentan
igualmente en valores de absorbancia, aunque, al contrario que las experiencias de IRRAS,
las bandas negativas indican especies formadas en el potencial de estudio, mientras que las
bandas positivas muestran especies consumidas respecto al espectro de referencia.
La configuración DEMS [109] está basada en un sistema de bombeo con dos
cámaras de vacío similar al de la Fig. 1.11 equipado con un espectrómetro ‘Balzers QMS
Capítulo 1: Síntesis
32
112 quadrupole mass spectrometer’. Se obtiene una mayor sensibilidad producto de las dos
bombas de vacío que favorece el alcance de las condiciones de alto vacío necesario y del
posicionamiento de la fuente de iones del espectrómetro entre las dos bombas, lo cual
beneficia la mayor eficiencia de ionización en las especies estudiadas.
1.2.4 Microscopia electrónica de transmisión (TEM)
Las muestras de nanopartículas de platino se caracterizaron usando la microscopía
electrónica de transmisión (TEM), que da información acerca del tamaño y del grado de
aglomeración. La técnica se basa en la interacción de un haz de electrones con la muestra
para su visualización, haciendo uso de la trasmisión/dispersión de los electrones para
formar la imagen, la difracción de los electrones para conocer la estructura cristalina y la
emisión de rayos X característicos para obtener información acerca de la composición. El
microscopio está compuesto por un cañón que emite los electrones hacia la muestra, lentes
especiales que son capaces de crear campos magnéticos que dirigen y enfocan el haz de
electrones, un sistema de vacío para evitar las interacciones de los electrones con las
moléculas del aire, una pantalla fluorescente que permita visualizar la imagen aumentada y
un ordenador como sistema de registro de la imagen. Las muestras se preparan depositando
unas gotas de la disolución micelar en rejillas de microscopía, que posteriormente se dejan
secar. El sistema utilizado fue un Microscopio Electrónico de Transmisión JEOL modelo
JEM-2010 con un detector de rayos X marca OXFORD modelo INCA Energy TEM 100
disponible en los Servicios Técnicos de la Universidad de Alicante.
Caracterización superficial
33
1.3 Caracterización superficial
Una parte importante, previa a los estudios de electrocatálisis, es la caracterización
física de las superficies de platino estudiadas, con el objetivo de averiguar la disposición
cristalográfica de los átomos en el catalizador. En condiciones de UHV, la caracterización
física se puede realizar con técnicas de difracción de rayos X o difracción de electrones de
baja o de alta energía (en sus siglas en inglés, LEED o HEED respectivamente), donde se
hace incidir sobre la muestra un haz de electrones de energía definida y se registra la
intensidad del haz dispersado en función de la energía y del ángulo de incidencia [110].
Por otra parte, una técnica muy común para la caracterización superficial es la
microscopía de efecto túnel (STM), donde una punta metálica barre la superficie de
materiales conductores registrándose la corriente túnel como medida de la distancia de la
punta a la superficie. El STM se puede considerar como una técnica ‘in situ’ donde la
caracterización se realiza en presencia del electrolito. Tanto las técnicas de difracción de
electrones que funcionan en condiciones de UHV como el STM requieren demasiado
tiempo y son costosas para ser prácticas en un trabajo frecuente. Por ello, es beneficioso
usar otros métodos de caracterización indirectos más sencillos, preferiblemente in situ. A
partir de la utilización del tratamiento a la llama desarrollado por Clavilier a partir de los
años 80, se obtuvieron superficies limpias y ordenadas de electrodos metálicos
monocristalinos sin necesidad de utilizar sistemas de UHV y consiguiendo caracterizar las
superficies de platino con una simple voltametría cíclica.
1.3.1 Monocristales de platino
Los electrodos monocristalinos de platino se preparan siguiendo el método
desarrollado por Clavilier [111, 112], el cual también es válido para la preparación de
electrodos monocristalinos de oro [113, 114], rodio [115, 116], iridio [117-119] o paladio
[120, 121]. En dicho método, un hilo de platino de elevada pureza y de unos 0.5 mm de
diámetro es fundido por uno de los extremos mediante una llama de oxígeno-propano,
produciendo una gota de metal fundido de unos 2-3 mm de diámetro para los electrodos de
Capítulo 1: Síntesis
34
trabajo utilizados en experimentos electroquímicos, y 5-6 mm para los electrodos
empleados en experimentos espectroelectroquímicos. La gota de metal fundido se enfría
muy lentamente, tratando de producir únicamente la cristalización en un único cristal.
Posteriormente, la esfera monocristalina, unida al hilo de platino, se coloca en un banco
óptico con un goniómetro y un láser que permiten identificar las facetas del cristal y la
orientación del monocristal en la dirección deseada. A continuación se realiza el corte y
pulido, mediante un sistema que permite la operación manteniendo la dirección
perpendicular al eje del banco óptico. Para el pulido del monocristal, se utilizaron
materiales abrasivos como carburo de silicio o pasta de diamante de hasta 0.25 µm.
Antes de la publicación del procedimiento de trabajo con monocristales de platino de
Clavilier, la forma más habitual para limpiar la superficie era mediante ciclos de
oxidación-reducción [122-125]. A pesar de la correcta preparación de las superficies
monocristalinas en condiciones UHV, al realizar el transvase a la célula electroquímica se
observaban impurezas adsorbidas sobre el electrodo que se eliminaban recurriendo a ciclos
de oxidación hasta potenciales superiores más altos de 1 V, donde se empiezan a formar
óxidos de platino. El problema de alcanzar estos potenciales es la alteración de la
superficie del electrodo al llegar a la zona de oxidación del platino, lo que se refleja en la
carga de adsorción a potenciales bajos, que involucra más de un átomo de hidrógeno por
átomo de platino [122].
El tratamiento a la llama de Clavilier [111] dio solución a este problema. El
procedimiento se basa en calentar el electrodo con un mechero Bunsen para oxidar las
impurezas adsorbidas procedentes del ambiente, aprovechando las propiedades catalíticas
del platino, y favoreciendo además la reorganización de la superficie. Posteriormente, el
electrodo, todavía a altas temperaturas, se introduce en un balón de enfriamiento dejándolo
en una atmósfera libre de oxígeno. Antes de que la temperatura del electrodo disminuya lo
suficiente como para verse afectado de nuevo por la adsorción de impurezas presentes en la
atmósfera, el electrodo se sumerge en agua ultrapura contenida en el balón de
enfriamiento, quedando protegido con una gota de dicha agua e impidiendo su
contaminación durante el traslado a la célula electroquímica.
Caracterización superficial
35
Un factor importante a tener en cuenta es el de la naturaleza de la atmósfera en la
cual se produce el enfriamiento del electrodo, ya que la adsorción de oxígeno en algunas
superficies puede afectar a la correcta ordenación de la estructura final debido a la
formación de óxidos térmicos. Por ello, el enfriamiento se lleva a cabo en una atmósfera
reductora H2 + Ar para preservar la superficie, sobre todo en el caso de los electrodos de
Pt(110), Pt(100) y las escalonadas con terrazas 111 y escalones 110 o 100. En el
caso de los electrodos de Pt(111), el enfriamiento del electrodo en atmósfera de Ar es
suficiente para obtener la correcta ordenación de la superficie monocristalina, debido a que
es la orientación con mayor densidad atómica superficial y, por tanto, la más estable y
menos sensible a la formación de óxidos superficiales.
La notación empleada en el párrafo anterior para nombrar los diferentes planos
cristalográficos son los denominados índices de Miller, que se definen como el producto
entre la recíproca de la intersección del plano cristalográfico y los ejes de coordenadas
(x,y,z) con el mínimo común múltiplo de dichas recíprocas, con el objetivo de que siempre
sean números enteros. Los índices de Miller constan de tres números (h,k,l) para
estructuras cúbicas y cuatro en el caso de estructuras hexagonales compactas (w,x,y,z).
Como el platino presenta estructura cúbica centrada en las caras (fcc, en sus siglas en
inglés), durante toda la tesis los índices de Miller indicados se representan como tres
números referidos a planos cristalográficos del platino.
Fig. 1.13. Representación de los planos base de índice de Miller 111, 100 y 110 para una
estructura cúbica centrada en las caras, mostrando la disposición de los átomos y la celdilla unidad
característica de cada plano. Figura tomada de la referencia [110].
Capítulo 1: Síntesis
36
La Fig. 1.13 muestra las distribuciones de los átomos en la celdilla unidad cúbica
centrada en las caras para las superficies más sencillas con los índices de Miller más bajos,
denominados planos base, y caracterizados por tener solamente un tipo de simetría,
hexagonal para las 111, cuadradas para las 100 y rectangular en el caso de las
superficies 110. Además, en cada superficie se muestran entre corchetes los vectores que
indican la dirección de los ejes que forman cada superficie. Todas las superficies están
formadas por diferentes contribuciones de los tres planos base, las cuales vienen
representadas en el triángulo estereográfico:
Fig. 1.14. Triángulo estereográfico.
Las tres esquinas del triángulo se corresponden con electrodos que poseen terrazas de
longitud infinita de una superficie de cada plano base. En los lados del triángulo, se indican
superficies con contribuciones de los planos base que forman el lado del triángulo. Por
ejemplo, la superficie Pt(554) presenta terrazas de nueve átomos de terraza 111,
separados por escalones monoatómicos 110. A este tipo de superficies se conoce como
escalonadas, compuestas por átomos de terraza con una orientación determinada separados
por escalones monoatómicos con otra ordenación. Por último, los índices de Miller que
aparecen en el interior del triángulo estereográfico contienen contribuciones de los tres
planos base, donde los escalones no son rectos y pueden presentarse diferentes esquinas.
Volviendo a las superficies escalonadas, la nomenclatura habitual con la que se
conocen es la propuesta por Lang [126]:
M (S) - [n (h,k,l) x (h’,k’,l’)] (1.30)
Caracterización superficial
37
donde M es el metal, n es el número de átomos presentes en la terraza, (h,k,l) es el índice
de Miller para la orientación de los átomos de terraza y (h’,k’,l’) es el índice de Miller
correspondiente a la orientación de los átomos de escalón. La Tabla 1.1 muestra la relación
entre la nomenclatura instruida por Lang y los índices de Miller para cada superficie
escalonada:
Superficies escalonadas Índices de Miller
n (111) x (111)
n (111) x (100)
n (100) x (111)
n (100) x (110)
n (110) x (111)
n (110) x (100)
(n, n, n-2)
(n+1, n-1, n-1)
(2n-1, 1, 1)
(n,1,0)
(2n-1, 2n-1, 1)
(n, n-1, 0)
Tabla 1.1. Relación entre la notación de superficies escalonadas propuesta por Lang y los índices de
Miller.
En el caso de algunas superficies escalonadas 111, son correctas dos notaciones
para indicar su simetría. Por ejemplo, la superficie con índice 553 se puede nombrar
como [5 (111) x (111)] o [4 (111) x (110)], ya que en una estructura cúbica centrada en las
caras una estructura 110 es equivalente a una superficie escalonada que presenta una
terrraza monoatómica con orientación 111 y un escalón monoatómico 111. La
asignación dependerá de su reactividad. Por otro lado, al moverse a través de los lados del
triángulo estereográfico, conforme más se alejan de los vértices, menor es la proporción de
esas terrazas a las superficies escalonadas. En el punto medio entre dos vértices, se
encuentra el denominado ‘turning point’, donde la relación entre los átomos de terraza y
escalón es de 1:1. Estas superficies son la 331, la 311 y la 210.
La correcta ordenación de todas las superficies y la limpieza de las disoluciones
utilizadas se comprueba con una voltametría cíclica previa, cuya respuesta está
Capítulo 1: Síntesis
38
perfectamente detallada en la literatura [127, 128]. Se adjunta como ejemplo la
caracterización electroquímica del Pt(111) en 0.5 M H2SO4.
Fig. 1.15. Voltametría cíclica para un electrodo de Pt(111) en 0.5 M H2SO4. v = 0.05 V s-1.
Las características de la voltametría del Pt(111) son una señal plana desde 0.05 hasta
0.25 V correspondiente con la zona de adsorción/desorción de hidrógeno. Al incrementar
el potencial hacia valores más positivos, a partir de 0.3 V la adsorción del anión sulfato
empieza a tener lugar sobre los sitios liberados por el hidrógeno entrando en la denominada
región de mariposa. El par de picos reversibles a 0.45 V se corresponde con una transición
de fase desorden-orden de la adcapa de SO42- [129], mientras que el par de picos
irreversibles que aparecen a 0.70 V en el barrido positivo y 0.67 V en el negativo no tiene
un origen del todo claro. Experiencias de desplazamiento de carga con CO sugieren que
son debidos mayoritariamente al anión sulfato [130, 131], resultados confirmados con
posteriores análisis termodinámicos [132, 133]. Además, los cationes presentes en el
electrolito ejercen una clara influencia en estos picos.
0.0 0.2 0.4 0.6 0.8
-0.15
-0.10
-0.05
0.00
0.05
0.10
0.15
j/mA
cm-2
E vs RHE/V
Caracterización superficial
39
1.3.2 Nanopartículas de platino
Como se ha mencionado anteriormente, los catalizadores de platino preparados a
partir de superficies monocristalinas son inviables en aplicaciones como pilas de
combustible, por lo que el platino se dispersa en forma de nanopartículas tratando de
optimizar la cantidad utilizada. El uso de nanopartículas como catalizadores en la
tecnología de las pilas de combustible ha sido ampliamente investigado en la bibliografía
[134-137].
Un parámetro importante a tener en cuenta en los estudios con nanopartículas es el
de su tamaño, afectando a la relación entre átomos presentes en la superficie y en el seno
del material. Si esta relación es muy alta, pueden producirse variaciones en las propiedades
electrónicas superficiales de los catalizadores. Por otra parte, conviene controlar la
estructura superficial de las nanopartículas, debido a su efecto en reacciones estudiadas en
electrocatálisis. En el año 1969, Van Hardeveld y Hartog [138] propusieron diferentes
modelos geométricos a partir de un número variable de átomos, los cuales indicaban la
relación entre las formas de las partículas y las orientaciones superficiales ideales para una
estructura cúbica centrada en las caras como la del platino. La Fig. 1.16 muestra dicha
relación para varias estructuras cristalográficas a partir del triángulo estereográfico:
Fig. 1.16. Relación entre las formas de las nanopartículas y su estructura cristalográfica ideal para
estructuras cúbicas centradas en las caras. Tomado de la referencia [139].
Capítulo 1: Síntesis
40
De acuerdo a la anterior figura, los dominios 111 se presentan en las formas
tetraédricas u octaédricas, los dominios 100 aparecen en partículas con forma de cubo y
los dominios 110 se presentarán idealmente en formas dodecaédricas truncadas
rómbicamente. El problema de las muestras de nanopartículas es la no posibilidad de
sintetizar por completo una única forma, pudiendo conseguirse alguna forma mayoritaria
pero siempre con presencia de partículas de otras formas. Además, las nanopartículas
contienen necesariamente otros tipos de sitio en bordes y esquinas. La notación empleada
en toda la tesis se refiere a nombrar como (100)Pt a las muestras que contienen
mayoritariamente forma cúbica, (111)Pt a las que presentan preferencia por las formas
octaédricas, (100)-(111)Pt para muestras que contienen mezcla de partículas con forma
octaédrica truncadas por cubos y (poly)Pt para las nanopartículas esféricas que no
presentan preferencia por ningún dominio. Además, se utilizan unas nanopartículas
esféricas soportadas en carbón Vulcan, señalando en cada muestra un porcentaje entre
paréntesis, el cual indica la masa de platino presente respecto a la masa total de catalizador.
Para la síntesis de las nanopartículas utilizadas en la tesis, se emplearon tres métodos
diferentes, dependiendo si se preparan nanopartículas con forma controlada u otras donde
no sea tan importante la forma debido a que el objetivo es el estudio de otros efectos como
la agregación de partículas. Estos métodos son:
• Método de microemulsión [140] para la preparación de nanopartículas de
platino esféricas poliorientadas, (poly)Pt, usadas en los capítulos en los que se
estudia el efecto de la estructura superficial.
• Método coloidal [34] para la realización de las nanopartículas de platino
preferencialmente cúbicas (100)Pt, octaédricas (111)Pt y las mezcladas (100)-
(111)Pt presentes en los estudios del efecto de la estructura superficial.
• Método citrato [141], para la elaboración de las muestras de platino con
diferente carga soportadas en carbón Vulcan, utilizadas en el capítulo 5 en el
estudio del efecto de la agregación de partículas en la oxidación de etanol.
Caracterización superficial
41
Otra parte importante al preparar los electrodos de trabajo a partir de nanopartículas
es la del soporte escogido para depositar las muestras. La característica principal que ha de
cumplir el soporte es el de no presentar ninguna señal faradaica que interfiera en el
intervalo de trabajo de las nanopartículas de Pt. Para preservar la estructura superficial de
las nanopartículas, al igual que en el caso de las superficies monocristalinas, no es
conveniente llegar a potenciales superiores a 0.95 V, ya que se entra en zona de formación
de óxidos de platino, que, al reducirse en el barrido negativo, podrían producir la variación
no deseada de la superficie inicial.
Los soportes empleados sobre los cuales se depositan las muestras de nanopartículas
son un sustrato hemisférico de oro poliorientado o un carbón vítreo comercial. Ambos
soportes no presentan corrientes faradaicas reseñables entre 0.05 y 1 V vs RHE,
potenciales a los cuales se estudian las reacciones de oxidación con etanol y con ácido
fórmico.
Fig. 1.17. Voltametría cíclica para: a) Soporte de Au policristalino, con la escala de la doble capa
aumentada (línea roja) y b) Soporte de carbón vítreo. Disolución test: 0.5 M H2SO4. Velocidad de barrido:
0.05 V s-1.
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8
-100
-80
-60
-40
-20
0
20
40
0.0 0.2 0.4 0.6 0.8 1.0-10
-5
0
5
10
i/µA
a)
i/µA
E vs RHE/V
b)
i/µA
E vs RHE/V
-20
-15
-10
-5
0
5
10
Capítulo 1: Síntesis
42
En un electrodo de Au policristalino, la evolución de hidrógeno se produce a
potenciales más negativos que en el platino. En la zona entre 0.05 y 1 V, en la que se
realizarán los experimentos, prácticamente sólo existe corriente capacitiva,
independientemente de la orientación superficial [114], confirmando su utilidad como
soporte para las nanopartículas. En el caso del carbón vítreo, tampoco se observan señales
faradaicas importantes, únicamente se distinguen un par de picos irreversibles a 0.68 V y
0.63 V que se asignan a la incorporación de grupos quinona a la estructura del carbón
vítreo [142]. Este último sustrato es menos conocido, particularmente en lo relacionado
con su limpieza.
Una vez realizados los experimentos, los soportes se pulen con alúmina preparada de
grano 0.3 micras para eliminar las nanopartículas del oro o del carbón vítreo. La
recuperación del perfil voltamétrico de la Fig. 1.17 corrobora la completa eliminación de
las nanopartículas después del pulido.
Un problema muy común cuando se trabaja con nanopartículas metálicas es el de la
correcta limpieza de la superficie manteniendo su estructura superficial. Muchos métodos
de síntesis [34, 140, 141, 143-146] utilizan surfactantes que han de ser eliminados antes de
comenzar con los estudios, con el objetivo de trabajar en superficies limpias para conseguir
reproducibilidad en los resultados. Como métodos de limpieza se han propuesto el ciclado
de las nanopartículas hasta potenciales superiores a la formación de óxidos superficiales
[147], la adición de disolventes orgánicos como hexano o ácido acético [146, 148] o el
tratamiento en una atmósfera en presencia de ozono [149]. El problema de estos métodos
de limpieza es que en muchas ocasiones provocan la modificación de la forma de las
nanopartículas. En nuestro grupo de investigación, la técnica de desplazamiento de carga
con CO sobre superficies monocristalinas de Pt [150, 151] muestra una total recuperación
del perfil voltamétrico correspondiente a un electrodo totalmente limpio después de su
adsorción con CO. De acuerdo a estos experimentos, a principio de la década de los 2000,
Solla-Gullón et. al. [152] propusieron un método sencillo basado en el desplazamiento de
las especies contaminantes de la superficie de las nanopartículas mediante la adsorción con
CO, el cual se oxida posteriormente, quedando la superficie limpia y sin problemas de
variación en la estructura superficial de las partículas. Todos los experimentos con
Caracterización superficial
43
nanopartículas realizados en la tesis se hicieron después de su limpieza de acuerdo a este
tratamiento en una disolución 0.5 M H2SO4.
Además, en las experiencias realizadas con electrodos de trabajo compuestos por
nanopartículas de platino modificados por un adátomo diferente, el depósito se hizo
mediante una voltametría cíclica en una disolución que contenía el precursor metálico con
una concentración 10-5-10-6 M en 0.5 M H2SO4, realizando un barrido de potenciales entre
0.06 y 0.8 V. No obstante, la forma en la que se modifica la superficie de platino es
diferente dependiendo del adátomo adsorbido:
• UPD (under potential deposition en sus siglas en inglés), donde el átomo de
la segunda especie se deposita a potenciales más positivos al termodinámico,
como en el caso del Tl, Sn y Pb. En este caso, el enlace entre el metal
substrato (Pt en forma de nanopartículas) y los átomos depositados de la
segunda especie (adátomos) es más fuerte que en el caso de un depósito
másico normal a potenciales más negativos [153, 154]. Esta técnica permite
un control preciso y reproducible del recubrimiento de metal depositado
sobre el sustrato. Además, la existencia de equilibrio entre el precursor
metálico presente en la disolución y el adátomo implica una relación entre el
potencial del electrodo y su recubrimiento superficial.
• Adsorción irreversible de adátomos [155, 156], como en el caso del Rh y el
Ru, donde dichos adátomos se adsorben de manera irreversible sobre la
superficie de las nanopartículas de platino, permaneciendo sobre el sustrato
de platino aún en ausencia del precursor metálico. No hay equilibrio entre las
especies presentes en disolución y el adátomo correspondiente, por lo que el
potencial puede variarse sin efecto alguno sobre el recubrimiento superficial
del adátomo en las nanopartículas de platino, dentro de ciertos límites.
El control del recubrimiento del adátomo se lleva a cabo mediante voltametría
cíclica, generalmente con la disminución de la carga de adsorción de hidrógeno
característica del Pt. En todos los casos planteados en esta tesis, únicamente para la
adsorción de Rh no se puede utilizar dicha carga para el cálculo del recubrimiento, debido
Capítulo 1: Síntesis
44
a que su voltagrama presenta picos para la adsorción de hidrógeno a potenciales similares a
los del platino.
Al igual que en el caso de los monocristales de platino, la manera de caracterizar las
nanopartículas de platino es mediante una simple voltametría cíclica, una vez realizados
los procesos de limpieza con CO indicados en esta sección. La caracterización
electroquímica de las nanopartículas utilizadas ha sido publicada en los últimos años por
nuestro grupo de investigación [33, 145, 157, 158]. Dichos resultados coinciden con
nuestras caracterizaciones, las cuales vienen representadas en cada capítulo de la tesis en
que se hayan empleado nanopartículas de platino como electrodo de trabajo.
Objetivo de la tesis
45
1.4 Objetivo de la tesis
La investigación efectuada en esta tesis se engloba dentro de los estudios de
electrocatálisis para la oxidación de pequeñas moléculas orgánicas de interés en la
tecnología de las pilas de combustible. Concretamente, se emplean el etanol y el ácido
fórmico como moléculas de estudio, realizando investigaciones fundamentales a
temperatura ambiente usando superficies de platino como catalizadores, ya sean superficies
monocristalinas o nanopartículas de platino. Estos estudios fundamentales buscan
maximizar la cantidad de CO2 formado a potenciales bajos, evitando en lo posible la
formación de especies que envenenen la superficie inhibiendo la actividad catalítica del
platino, como CO en el caso del ácido fórmico o CO y aniones acetato en el etanol.
Para llevar a cabo los estudios de electrocatálisis de oxidación de etanol y ácido
fórmico se han recurrido a técnicas electroquímicas (voltametría cíclica y
cronoamperometría) donde se obtiene información acerca de qué superficies son más
activas y requieren menos sobrepotenciales para llevar a cabo las oxidaciones. La
espectroscopía FTIR de reflexión externa se emplea para conocer con exactitud las
especies adsorbidas o formadas a cada potencial a medida que prosigue la oxidación,
pudiendo, por ejemplo, distinguir entre la cantidad de CO adsorbido o acetato formado (no
deseado) en el caso del etanol o si en la oxidación de ácido fórmico se consigue catalizar la
conversión de CO a CO2. Por último, las experiencias con espectrometría de masas
electroquímica en condiciones de flujo permiten la obtención de datos cuantitativos muy
útiles para conocer con mayor exactitud las diferencias entre catalizadores de platino
preparados a partir de nanopartículas de platino con diferentes estructuras superficiales.
Tomando como base los resultados publicados por Colmati et.al. para la oxidación
de etanol utilizando superficies monocristalinas de platino [71], el capítulo 2 de la tesis
tiene como objetivo comprobar si el mismo comportamiento observado respecto al efecto
de la estructura superficial en electrodos monocristalinos de platino se conserva en el caso
de nanopartículas de platino con orientación preferencial, sintetizadas en nuestro grupo de
investigación de la Universidad de Alicante y utilizadas en estudios de electrocatálisis [33,
159, 160]. Además, también se investiga la influencia de la posible adsorción de aniones
presentes en el electrolito soporte en la misma oxidación de etanol.
Capítulo 1: Síntesis
46
El mecanismo de oxidación de etanol varía si se modifica el pH de la disolución de
trabajo. Manteniendo en todo momento pHs ácidos y una concentración constante de
electrolito soporte, el capítulo 3 estudia los cambios producidos en dicho mecanismo al
aumentar ligeramente el pH, trabajando con dos muestras de nanopartículas de platino: con
preferencia por dominios 100 y con preferencia por dominios 111. Solo se utilizan
estas dos muestras porque son las que muestran comportamientos más extremos en cuanto
a la oxidación de etanol. Estos estudios se hacen en un sistema con células de flujo [107],
una situación más parecida a la empleada en las pilas de combustible. En este sentido, debe
pensarse que un aumento del pH aumentará la resistencia del electrolito.
En el capítulo 4 se comienza con el estudio de la oxidación de etanol en medio
alcalino. Primero de todo, para una mejor comprensión de la reacción, se emplean
superficies monocristalinas de platino con la estructura cristalográfica perfectamente
conocida. Las investigaciones realizadas son similares a las efectuadas por Colmati et. al.
en medio ácido [71, 76], en primer lugar con los planos basales para conocer como varía la
actividad al trabajar en pHs opuestos y posteriormente con superficies escalonadas 100 o
110 en terrazas 111 para ver su efecto para la catálisis de etanol. Por otra parte, se
comparan los espectros IR obtenidos con espectros de transmisión de probables productos
a un mismo pH, de igual manera a lo realizado por experimentos del grupo de Sun [161].
Los resultados se comparan con trabajos similares para la oxidación de etanol en platino a
pH alcalino [86, 162, 163].
En la misma línea de los estudios realizados en el capítulo 2 de la tesis, el capítulo 5
busca confirmar los mismos resultados de electrocatálisis con superficies monocristalinas
de platino en medio alcalino con las nanopartículas de platino con orientación preferencial,
incidiendo además en la estabilidad de la catálisis de las nanopartículas de platino con el
tiempo a un potencial fijo. Este capítulo presenta además otra parte, donde se investiga el
efecto de agregación en nanopartículas poliorientadas soportadas en carbón con diferentes
cantidades de platino en las muestras, que en medio ácido inhibe las reacciones de
oxidación de etanol y ácido fórmico [164].
A partir del capítulo 6 se inicia el estudio de la influencia de la adsorción de un metal
diferente al platino sobre las nanopartículas de platino. La adición de adátomos como el
Objetivo de la tesis
47
Sb, el Bi, o el Pd entre otros provoca una mejora en cuanto a la actividad total y al
potencial al cual se inicia la oxidación de ácido fórmico en superficies monocristalinas [53,
54, 56, 165]. Se ha observado el mismo efecto catalítico en las muestras de nanopartículas
de platino con orientaciones preferenciales 100 y orientaciones preferenciales 111
decorada con Sb o Pd [92, 166]. En este capítulo se estudia el efecto de la adsorción de
talio sobre las mismas muestras de nanopartículas cúbicas y octaédricas en medio ácido
para la oxidación de ácido fórmico.
Por último, en el capítulo 7 de la tesis se realizan investigaciones similares con
adátomos sobre las superficies de las nanopartículas de platino, pero para la oxidación de
etanol. Los catalizadores preparados con la combinación entre Pt y otro metal se muestran
muy beneficiosas para la optimización de la reacción de oxidación de etanol, como por
ejemplo Rh o Sn [80, 167-169] o la combinación entre diferentes metales con el platino
[93, 170]. Siguiendo la estrategia de adsorber átomos de diferentes metales sobre las
nanopartículas de platino, trabajos previos realizados con superficies de platino muestran el
efecto positivo de la adición de otros átomos junto al platino para la eliminación del
veneno, como es el caso de Sn [78], Ru [77, 171], Os [82, 172] o Pb [173, 174]. En este
capítulo, se busca algún adátomo que funcione de forma similar con las nanopartículas de
platino a pHs ácidos y a pHs alcalinos, tratando de encontrar la combinación óptima para
cada electrolito soporte.
Capítulo 1: Síntesis
48
1.5 Referencias
[1] W. Schmickler, ''Interfacial Electrochemistry'', Oxford University Press, New York, 1996.
[2] J. O. M. Bockris and A. K. N. Reddy, ''Modern Electrochemistry'', Plenum, New York, 1970.
[3] W. Schuhmann and E. M. Bonsen, ''Biosensors'', in Encyclopedia of Electrochemistry, Wiley, 2007.
[4] Y. Li, H. J. Schluesener and S. Xu, ''Gold nanoparticle-based biosensors'' Gold Bulletin 2010, 43, 29-41.
[5] F. W. Campbell and R. G. Compton, ''The use of nanoparticles in electroanalysis: An updated review'' Analytical and Bioanalytical Chemistry 2010, 396, 241-259.
[6] J. M. Pingarrón Carrazón and P. Sánchez Batanero, ''Química electroanalítica: fundamentos y aplicaciones'', Síntesis, 1999.
[7] B. Oregan and M. Grätzel, ''A low-cost, high-efficiency solar cell based on dye-sensitized colloidal TiO2 films'' Nature 1991, 353, 737-740.
[8] I. Sirés and E. Brillas, ''Remediation of water pollution caused by pharmaceutical residues based on electrochemical separation and degradation technologies: A review'' Environment International 2012, 40, 212-229.
[9] T. Shono, ''Electroorganic chemistry in organic synthesis'' Tetrahedron 1984, 40, 811-850.
[10] J. Yoshida, K. Kataoka, R. Horcajada and A. Nagaki, ''Modern strategies in electroorganic synthesis'' Chemical Reviews 2008, 108, 2265-2299.
[11] A. J. Bard, M. Stratmann and G. S. Frankel, ''Corrosion and Oxide Films'', Encyclopedia of Electrochemistry vol. 4 A. J. Bard, M. Stratmann and G. S. Frankel (Eds.), Wiley VCH, 2003.
[12] P. Simon and Y. Gogotsi, ''Materials for electrochemical capacitors'' Nature Materials 2008, 7, 845-854.
[13] E. Frackowiak and F. Beguin, ''Carbon materials for the electrochemical storage of energy in capacitors'' Carbon 2001, 39, 937-950.
[14] M. S. Whittingham and T. Zawodzinski, ''Introduction: Batteries and Fuel Cells'' Chemical Reviews 2004, 104, 4243-4244.
[15] J. M. Tarascon and M. Armand, ''Issues and challenges facing rechargeable lithium batteries'' Nature 2001, 414, 359-367.
[16] C. P. de León, A. Frías-Ferrer, J. González-García, D. A. Szanto and F. C. Walsh, ''Redox flow cells for energy conversion'' Journal of Power Sources 2006, 160, 716-732.
[17] S. Srinivasan, ''Fuel Cells: From fundamental to Applications'', Springer, 2006.
[18] ''Fuel Cell Handbook'', U.S. Department of Energy, Morgantown, West Virginia, 2000.
[19] S. Rousseau, C. Coutanceau, C. Lamy and J. M. Léger, ''Direct ethanol fuel cell (DEFC): Electrical performances and reaction products distribution under operating conditions with different platinum-based anodes'' Journal of Power Sources 2006, 158, 18-24.
[20] S. Song, W. Zhou, Z. Liang, R. Cai, G. Sun, Q. Xin, V. Stergiopoulos and P. Tsiakaras, ''The effect of methanol and ethanol cross-over on the performance of PtRu/C-based anode DAFCs'' Applied Catalysis B: Environmental 2005, 55, 65-72.
[21] C. Rice, R. I. Ha, R. I. Masel, P. Waszczuk, A. Wieckowski and T. Barnard, ''Direct formic acid fuel cells'' Journal of Power Sources 2002, 111, 83-89.
[22] A. Wojcik, H. Middleton, I. Damopoulos and J. Van Herle, ''Ammonia as a fuel in solid oxide fuel cells'' Journal of Power Sources 2003, 118, 342-348.
[23] K. Yamada, K. Asazawa, K. Yasuda, T. Ioroi, H. Tanaka, Y. Miyazaki and T. Kobayashi, ''Investigation of PEM type direct hydrazine fuel cell'' Journal of Power Sources 2003, 115, 236-242.
Referencias
49
[24] S. C. Amendola, P. Onnerud, M. T. Kelly, P. J. Petillo, S. L. Sharp-Goldman and M. Binder, ''A novel high power density borohydride-air cell'' Journal of Power Sources 1999, 84, 130-133.
[25] I. Willner, Y. M. Yan, B. Willner and R. Tel-Vered, ''Integrated Enzyme-Based Biofuel Cells-A Review'' Fuel Cells 2009, 9, 7-24.
[26] Z. W. Du, H. R. Li and T. Y. Gu, ''A state of the art review on microbial fuel cells: A promising technology for wastewater treatment and bioenergy'' Biotechnology Advances 2007, 25, 464-482.
[27] J. S. Spendelow and A. Wieckowski, ''Electrocatalysis of oxygen reduction and small alcohol oxidation in alkaline media'' Physical Chemistry Chemical Physics 2007, 9, 2654-2675.
[28] D. Takky, B. Beden, J. M. Léger and C. Lamy, ''Evidence for the effect of molecular structure on the electrochemical reactivity of alcohols: Part I. Electrooxidation of the butanol isomers on noble metal electrodes in alkaline medium'' Journal of Electroanalytical Chemistry 1983, 145, 461-466.
[29] C. Lamy and C. Coutanceau, ''Electrocatalysis of Alcohol Oxidation Reactions at Platinum Group Metals'', in Catalysts for Alcohol-Fuelled Direct Oxidation Fuel Cells, vol. 6, Z.-X. Liang and T. S. Zhao (Eds.) RSC Energy and Enviroment Series 2012.
[30] C. Lamy and J. M. Léger, ''Electrocatalytic oxidation of small organic molecules at platinum single crystals'' Journal de Chimie Physique et de Physico-Chimie Biologique 1991, 88, 1649-1671.
[31] Y. Ishikawa, M. S. Liao and C. R. Cabrera, ''Oxidation of methanol on platinum, ruthenium and mixed Pt-M metals (M = Ru, Sn): a theoretical study'' Surface Science 2000, 463, 66-80.
[32] G. A. Camara and T. Iwasita, ''Parallel pathways of ethanol oxidation: The effect of ethanol concentration'' Journal of Electroanalytical Chemistry 2005, 578, 315-321.
[33] J. Solla-Gullón, P. Rodríguez, E. Herrero, A. Aldaz and J. M. Feliu, ''Surface characterization of platinum electrodes'' Physical Chemistry Chemical Physics 2008, 10, 1359-1373.
[34] T. S. Ahmadi, Z. L. Wang, T. C. Green, A. Henglein and M. A. El-Sayed, ''Shape-controlled synthesis of colloidal platinum nanoparticles'' Science 1996, 272, 1924-1926.
[35] S. Uhm, H. J. Lee and J. Lee, ''Understanding underlying processes in formic acid fuel cells'' Physical Chemistry Chemical Physics 2009, 11, 9326-9336.
[36] A. Capon and R. Parsons, ''The oxidation of formic acid at noble metal electrodes Part III. Intermediates and mechanism on platinum electrodes'' Journal of Electroanalytical Chemistry 1973, 45, 205-231.
[37] J. M. Feliu and E. Herrero, ''Formic acid oxidation'', in Handbook of Fuel Cells - Fundamentals, Technology and Applications, vol. 2, W. Vielstich, H. Gasteiger and A. Lamm (Eds.) Wiley, Chichester, 2003, pp. 625-634.
[38] K. Kunimatsu, ''Infrared spectroscopic study of methanol and formic acid adsorbates on a platinum electrode: Part I. Comparison of the infrared absorption intensities of linear CO(a) derived from CO, CH3OH and HCOOH'' Journal of Electroanalytical Chemistry 1986, 213, 149-157.
[39] S. G. Sun, J. Clavilier and A. Bewick, ''The mechanism of electrocatalytic oxidation of formic acid on Pt (100) and Pt (111) in sulphuric acid solution: an EMIRS study'' Journal of Electroanalytical Chemistry 1988, 240, 147-159.
[40] Y. X. Chen, M. Heinen, Z. Jusys and R. J. Behm, ''Bridge-bonded formate: Active intermediate or spectator species in formic acid oxidation on a Pt film electrode?'' Langmuir 2006, 22, 10399-10408.
[41] S. C. Chang, L. W. H. Leung and M. J. Weaver, ''Metal crystallinity effects in electrocatalysis as probed by real-time FTIR spectroscopy: electrooxidation of formic acid, methanol, and ethanol on ordered low-index platinum surfaces'' Journal of Physical Chemistry 1990, 94, 6013-6021.
[42] A. Miki, S. Ye and M. Osawa, ''Surface-enhanced IR absorption on platinum nanoparticles: an application to real-time monitoring of electrocatalytic reactions'' Chemical Communications (Cambridge, United Kingdom) 2002, 1500-1501.
Capítulo 1: Síntesis
50
[43] A. Cuesta, G. Cabello, M. Osawa and C. Gutiérrez, ''Mechanism of the Electrocatalytic Oxidation of Formic Acid on Metals'' ACS Catalysis 2012, 2, 728-738.
[44] Y. X. Chen, M. Heinen, Z. Jusys and R. B. Behm, ''Kinetics and mechanism of the electrooxidation of formic acid - Spectroelectrochemical studies in a flow cell'' Angewandte Chemie, International Edition in English 2006, 45, 981-985.
[45] Y. X. Chen, M. Heinen, Z. Jusys and R. J. Behm, ''Kinetic isotope effects in complex reaction networks: Formic acid electro-oxidation'' ChemPhysChem 2007, 8, 380-385.
[46] J. Joo, T. Uchida, A. Cuesta, M. T. M. Koper and M. Osawa, ''Importance of Acid-Base Equilibrium in Electrocatalytic Oxidation of Formic Acid on Platinum'' Journal of the American Chemical Society 2013, 135, 9991-9994.
[47] S. Brimaud, J. Solla-Gullón, I. Weber, J. M. Feliu and R. J. Behm, ''Formic Acid Electrooxidation on Noble-Metal Electrodes: Role and Mechanistic Implications of pH, Surface Structure, and Anion Adsorption'' ChemElectroChem 2014, 1, 1075-1083.
[48] J. Clavilier, R. Parsons, R. Durand, C. Lamy and J. M. Léger, ''Formic acid oxidation on single crystal platinum electrodes. Comparison with polycrystalline platinum'' Journal of Electroanalytical Chemistry 1981, 124, 321-326.
[49] N. M. Markovic and P. N. Ross, ''Surface science studies of model fuel cell electrocatalysts'' Surface Science Reports 2002, 45, 117-229.
[50] J. Clavilier, A. Fernández-Vega, J. M. Feliu and A. Aldaz, ''Heterogeneous electrocatalysis on well defined platinum surfaces modified by controlled amounts of irreversibly adsorbed adatoms: Part I. Formic-acid oxidation on the Pt (111) - Bi system'' Journal of Electroanalytical Chemistry 1989, 258, 89-100.
[51] J. Clavilier, A. Fernández-Vega, J. M. Feliu and A. Aldaz, ''Heterogeneous electrocatalysis on well-defined platinum surfaces modified by controlled amounts of irreversibly adsorbed adatoms: Part III. Formic-acid oxidation on the Pt(100)-Bi system'' Journal of Electroanalytical Chemistry 1989, 261, 113-125.
[52] S. A. Campbell and R. Parsons, ''Effect of Bi and Sn adatoms on formic acid and methanol oxidation at well defined platinum surfaces'' Journal of the Chemical Society, Faraday Transactions 1992, 88, 833-841.
[53] E. Herrero, J. M. Feliu and A. Aldaz, ''Poison formation reaction from formic acid on Pt(100) electrodes modified by irreversibly adsorbed bismuth and antimony'' Journal of Electroanalytical Chemistry 1994, 368, 101-108.
[54] Y.-Y. Yang, S.-G. Sun, Y.-J. Gu, Z.-Y. Zhou and C.-H. Zhen, ''Surface modification and electrocatalytic properties of Pt(100), Pt(110), Pt(320) and Pt(331) electrodes with Sb towards HCOOH oxidation'' Electrochimica Acta 2001, 46, 4339-4348.
[55] H. W. Lei, H. Hattori and H. Kita, ''Electrocatalysis by Pb adatoms of HCOOH oxidation at Pt(111) in acidic solution'' Electrochimica Acta 1996, 41, 1619-1628.
[56] F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero, A. Aldaz and J. M. Feliu, ''Formic acid oxidation on Pd-modified Pt(100) and Pt(111) electrodes: A DEMS study'' Journal of Applied Electrochemistry 2006, 36, 1207-1214.
[57] E. Herrero, M. J. Llorca, J. M. Feliu and A. Aldaz, ''Oxidation of formic acid on Pt(100) electrodes modified by irreversibly adsorbed tellurium'' Journal of Electroanalytical Chemistry 1995, 383, 145-154.
[58] M. J. Llorca, E. Herrero, J. M. Feliu and A. Aldaz, ''Formic acid oxidation on Pt(111) electrodes modified by irreversibly adsorbed selenium'' Journal of Electroanalytical Chemistry 1994, 373, 217-225.
[59] A. Fernández-Vega, J. M. Feliu, A. Aldaz and J. Clavilier, ''Heterogeneous electrocatalysis on well-defined platinum surfaces modified by controlled amounts of irreversibly adsorbed adatoms: Part IV. Formic acid oxidation on the Pt(111)-As system'' Journal of Electroanalytical Chemistry 1991, 305, 229-240.
Referencias
51
[60] A. Boronat-González, E. Herrero and J. M. Feliu, ''Fundamental aspects of HCOOH oxidation at platinum single crystal surfaces with basal orientations and modified by irreversibly adsorbed adatoms'' Journal of Solid State Electrochemistry 2014, 18, 1181-1193.
[61] T. Iwasita, B. Rasch, E. Cattaneo and W. Vielstich, ''A SNIFTIRS study of ethanol oxidation on platinum'' Electrochimica Acta 1989, 34, 1073-1079.
[62] J. Willsau and J. Heitbaum, ''Elementary steps of ethanol oxidation on Pt in sulfuric acid as evidenced by isotope labeling'' Journal of Electroanalytical Chemistry 1985, 194, 27-35.
[63] R. Kavanagh, X.-M. Cao, W.-F. Lin, C. Hardacre and P. Hu, ''Origin of Low CO2 Selectivity on Platinum in the Direct Ethanol Fuel Cell'' Angewandte Chemie International Edition 2012, 51, 1572-1575.
[64] A. Rodes, E. Pastor and T. Iwasita, ''An FTIR Study on the Adsorption of Acetate at the Basal Planes of Platinum Single-Crystal Electrodes'' Journal of Electroanalytical Chemistry 1994, 376, 109-118.
[65] T. Iwasita and E. Pastor, ''A DEMS and FTIR spectroscopic investigation of adsorbed ethanol on polycrystalline platinum'' Electrochimica Acta 1994, 39, 531-537.
[66] H. Wang, Z. Jusys and R. J. Behm, ''Ethanol electrooxidation on a carbon-supported Pt catalyst: Reaction kinetics and product yields'' Journal of Physical Chemistry B 2004, 108, 19413-19424.
[67] M. Heinen, Z. Jusys and R. J. Behm, ''Ethanol, Acetaldehyde and Acetic Acid Adsorption/Electrooxidation on a Pt Thin Film Electrode under Continuous Electrolyte Flow: An in Situ ATR-FTIRS Flow Cell Study'' Journal of Physical Chemistry C 2010, 114, 9850-9864.
[68] J. Souza-Garcia, E. Herrero and J. M. Feliu, ''Breaking the C-C Bond in the Ethanol Oxidation Reaction on Platinum Electrodes: Effect of Steps and Ruthenium Adatoms'' ChemPhysChem 2010, 11, 1391-1394.
[69] X. H. Xia, H. D. Liess and T. Iwasita, ''Early stages in the oxidation of ethanol at low index single crystal platinum electrodes'' Journal of Electroanalytical Chemistry 1997, 437, 233-240.
[70] S. C. S. Lai and M. T. M. Koper, ''Electro-oxidation of ethanol and acetaldehyde on platinum single-crystal electrodes'' Faraday Discussions 2008, 140, 399-416.
[71] F. Colmati, G. Tremiliosi-Filho, E. R. Gonzalez, A. Berná, E. Herrero and J. M. Feliu, ''Surface structure effects on the electrochemical oxidation of ethanol on platinum single crystal electrodes'' Faraday Discussions 2008, 140, 379-397.
[72] U. Schmiemann, U. Müller and H. Baltruschat, ''The Influence of the Surface-Structure on the Adsorption of Ethene, Ethanol and Cyclohexene as Studied by DEMS'' Electrochimica Acta 1995, 40, 99-107.
[73] M. J. Prieto and G. Tremiliosi-Filho, ''The influence of acetic acid on the ethanol electrooxidation on a platinum electrode'' Electrochemistry Communications 2011, 13, 527-529.
[74] D. J. Tarnowski and C. Korzeniewski, ''Effects of surface step density on the electrochemical oxidation of ethanol to acetic acid'' Journal of Physical Chemistry B 1997, 101, 253-258.
[75] S. C. S. Lai and M. T. M. Koper, ''The Influence of Surface Structure on Selectivity in the Ethanol Electro-oxidation Reaction on Platinum'' Journal of Physical Chemistry Letters 2010, 1, 1122-1125.
[76] F. Colmati, G. Tremiliosi-Filho, E. R. Gonzalez, A. Berná, E. Herrero and J. M. Feliu, ''The role of the steps in the cleavage of the C-C bond during ethanol oxidation on platinum electrodes'' Physical Chemistry Chemical Physics 2009, 11, 9114-9123.
[77] V. Del Colle, A. Berná, G. Tremiliosi-Filho, E. Herrero and J. M. Feliu, ''Ethanol electrooxidation onto stepped surfaces modified by Ru deposition: electrochemical and spectroscopic studies'' Physical Chemistry Chemical Physics 2008, 10, 3766-3773.
[78] V. Del Colle, J. Souza-Garcia, G. Tremiliosi-Filho, E. Herrero and J. M. Feliu, ''Electrochemical and spectroscopic studies of ethanol oxidation on Pt stepped surfaces modified by tin adatoms'' Physical Chemistry Chemical Physics 2011, 13, 12163-12172.
Capítulo 1: Síntesis
52
[79] W. Zhu, J. Ke, S. B. Wang, J. Ren, H. H. Wang, Z. Y. Zhou, R. Si, Y. W. Zhang and C. H. Yan, ''Shaping Single-Crystalline Trimetallic Pt-Pd-Rh Nanocrystals toward High-Efficiency C-C Splitting of Ethanol in Conversion to CO2'' ACS Catalysis 2015, 5, 1995-2008.
[80] J. P. I. de Souza, S. L. Queiroz, K. Bergamaski, E. R. Gonzalez and F. C. Nart, ''Electro-oxidation of ethanol on Pt, Rh, and PtRh electrodes. A study using DEMS and in-situ FTIR techniques'' Journal of Physical Chemistry B 2002, 106, 9825-9830.
[81] T. E. Shubina and M. T. M. Koper, ''Quantum-chemical calculations of CO and OH interacting with bimetallic surfaces'' Electrochimica Acta 2002, 47, 3621-3628.
[82] V. Del Colle, V. Santos and G. Tremiliosi-Filho, ''Comparative Electrochemical and Spectroscopic Studies of Ethanol Oxidation on Pt(h,k,l) Modified by Osmium Nanoislands'' Electrocatalysis 2010, 1, 144-158.
[83] J. Tayal, B. Rawat and S. Basu, ''Bi-metallic and tri-metallic Pt-Sn/C, Pt-Ir/C, Pt-Ir-Sn/C catalysts for electro-oxidation of ethanol in direct ethanol fuel cell'' International Journal of Hydrogen Energy 2011, 36, 14884-14897.
[84] W. Zhou, Z. Zhou, S. Song, W. Li, G. Sun, P. Tsiakaras and Q. Xin, ''Pt based anode catalysts for direct ethanol fuel cells'' Applied Catalysis B: Environmental 2003, 46, 273-285.
[85] S. C. S. Lai, S. E. F. Kleijn, F. T. Z. Öztürk, V. C. van Rees Vellinga, J. Koning, P. Rodriguez and M. T. M. Koper, ''Effects of electrolyte pH and composition on the ethanol electro-oxidation reaction'' Catalysis Today 2010, 154, 92-104.
[86] P. A. Christensen, S. W. M. Jones and A. Hamnett, ''In Situ FTIR Studies of Ethanol Oxidation at Polycrystalline Pt in Alkaline Solution'' Journal of Physical Chemistry C 2012, 116, 24681-24689.
[87] A. J. Bard and L. R. Faulkner, ''Electrochemical Methods. Fundamental and Applications'', John Wiley & Sons, Inc., New York, 2001.
[88] A. J. Bard and M. Stratmann, ''Instrumentation and Electroanalytical Chemistry'', Encyclopedia of Electrochemistry vol. 3 P. R. Unwin (Ed.), Wiley, 2003.
[89] P. Kissinger and W. R. Heineman, ''Laboratory Techniques in Electroanalytical Chemistry, Second Edition, Revised and Expanded'', Taylor & Francis, 1996.
[90] M. Bergelin and M. Wasberg, ''The impinging jet flow method in interfacial electrochemistry: an application to bead-type electrodes'' Journal of Electroanalytical Chemistry 1998, 449, 181-191.
[91] T. H. M. Housmans and M. T. M. Koper, ''CO oxidation on stepped Rh [n(111) x (111)] single crystal electrodes: a chronoamperometric study'' Journal of Electroanalytical Chemistry 2005, 575, 39-51.
[92] F. J. Vidal-Iglesias, A. López-Cudero, J. Solla-Gullón and J. M. Feliu, ''Towards More Active and Stable Electrocatalysts for Formic Acid Electrooxidation: Antimony-Decorated Octahedral Platinum Nanoparticles'' Angewandte Chemie-International Edition 2013, 52, 964-967.
[93] A. Kowal, M. Li, M. Shao, K. Sasaki, M. B. Vukmirovic, J. Zhang, N. S. Marinkovic, P. Liu, A. I. Frenkel and R. R. Adzic, ''Ternary Pt/Rh/SnO2 electrocatalysts for oxidizing ethanol to CO2'' Nature Materials 2009, 8, 325-330.
[94] F. M. Hoffmann, ''Infrared reflection-absorption spectroscopy of adsorbed molecules'' Surface Science Reports 1983, 3, 107-192.
[95] T. Iwasita and F. C. Nart, ''In situ infrared spectroscopy at electrochemical interfaces'' Progress in Surface Science 1997, 55, 271-340.
[96] A. Berná, A. Rodes and J. M. Feliu, ''In-situ FTIR Studies on the Acid-Base Equilibria of Adsorbed Species on Well-Defined Metal Electrode Surfaces'', in In-situ Spectroscopic Studies of Adsorption at the Electrode and Electrocatalysis, S.-G. Sun, P. A. Christensen and A. Wieckowski (Eds.) Elsevier, Amsterdam, 2007, pp. 1-32.
[97] G. Gauglitz and T. Vo-Dinh, ''Handbook of Spectroscopy'', Wiley, 2006.
Referencias
53
[98] T. Iwasita and F. C. Nart, ''In-Situ Fourier Transform Infrared Spectroscopy: A Tool to Characterize the Metal-Electrolyte Interface at a Molecular Level'', in Advances in Electrochemical Science and Engineering, vol. 4, Wiley, 2008, pp. 123-216.
[99] R. G. Greenler, ''Infrared Study of Adsorbed Molecules on Metal Surfaces by Reflection Techniques'' The Journal of Chemical Physics 1966, 44, 310-315.
[100] A. Rodes, J. M. Pérez and A. Aldaz, ''Vibrational spectroscopy'', in Handbook of Fuel Cells - Fundamentals, Technology and Applications, vol. 2, W. Vielstich, A. Lamm and H. A. Gasteiger (Eds.) Wiley, Chichester, 2003, pp. 191-219.
[101] M. Osawa, ''In-situ Surface-Enhanced Infrared Spectroscopy of the Electrode/Solution Interface'', in Advances in Electrochemical Science and Engineering, vol. 9, Wiley, 2008, pp. 269-314.
[102] Z. M. Khoshhesab, ''Reflectance IR spectroscopy'', INTECH Open Access Publisher, 2012.
[103] M. Osawa, ''Surface-Enhanced Infrared Absorption Spectroscopy'', in Handbook of Vibrational Spectroscopy, vol. 1, Wiley, 2006, pp. 785-799.
[104] H. Baltruschat, ''Differential electrochemical mass spectrometry'' Journal of the American Society for Mass Spectrometry 2004, 15, 1693-1706.
[105] O. Wolter and J. Heitbaum, ''Differential Electrochemical Mass-Spectroscopy (DEMS) - a New Method for the Study of Electrode Process'' Berichte Der Bunsen-Gesellschaft-Physical Chemistry Chemical Physics 1984, 88, 2-6.
[106] S. J. Ashton, ''Design, Construction and Research Application of a Differential Electrochemical Mass Spectrometer (DEMS)'', Springer, 2012.
[107] M. Heinen, Y. X. Chen, Z. Jusys and R. J. Behm, ''In situ ATR-FTIRS coupled with on-line DEMS under controlled mass transport conditions - A novel tool for electrocatalytic reaction studies'' Electrochimica Acta 2007, 52, 5634-5643.
[108] H. Miyake, S. Ye and M. Osawa, ''Electroless deposition of gold thin films on silicon for surface-enhanced infrared spectroelectrochemistry'' Electrochemistry Communications 2002, 4, 973-977.
[109] Z. Jusys and R. J. Behm, ''Methanol oxidation on a carbon-supported Pt fuel cell catalyst - A kinetic and mechanistic study by differential electrochemical mass spectrometry'' Journal of Physical Chemistry B 2001, 105, 10874-10883.
[110] V. Climent, ''Nueva aproximación al estudio de los potenciales de carga cero de electrodos monocristalinos del grupo del platino: aplicación al estudio de la adsorción iónica y molecular", Tesis doctoral, Universidad de Alicante, 1999.
[111] J. Clavilier, R. Faure, G. Guinet and R. Durand, ''Preparation of monocrystalline Pt microelectrodes and electrochemical study of the plane surfaces cut in the direction of the 111 and 110 planes'' Journal of Electroanalytical Chemistry 1980, 107, 205-209.
[112] J. Clavilier, ''The role of anion on the electrochemical behaviour of a 111 platinum surface; an unusual splitting of the voltammogram in the hydrogen region'' Journal of Electroanalytical Chemistry 1980, 107, 211-216.
[113] A. Hamelin, ''Double layer properties at sp and sd Metal Single-Crystal electrodes'', in Modern Aspects of Electrochemistry, vol. 16, Plenum, New York, 1985, pp. 1-101.
[114] A. Hamelin, ''Cyclic voltammetry at gold single-crystal surfaces: Part 1. Behaviour at low-index faces'' Journal of Electroanalytical Chemistry 1996, 407, 1-11.
[115] Q. Q. Xu, U. Linke, R. Bujak and T. Wandlowski, ''Preparation and electrochemical characterization of low-index rhodium single crystal electrodes in sulfuric acid'' Electrochimica Acta 2009, 54, 5509-5521.
[116] R. Gómez, J. M. Orts, J. M. Feliu, J. Clavilier and L. H. Klein, ''The role of surface crystalline heterogeneities in the electrooxidation of carbon monoxide adsorbed on Rh(111) electrodes in sulphuric acid solutions'' Journal of Electroanalytical Chemistry 1997, 432, 1-5.
[117] R. Gómez and M. J. Weaver, ''Electrochemical Infrared Studies of Monocrystalline Iridium Surfaces Part I: Electrooxidation of Formic-Acid and Methanol'' Journal of Electroanalytical Chemistry 1997, 435, 205-215.
Capítulo 1: Síntesis
54
[118] R. Gómez and M. J. Weaver, ''Electrochemical infrared studies of monocrystalline iridium surfaces. Part 2: Carbon monoxide and nitric oxide adsorption on Ir(110)'' Langmuir 1998, 14, 2525-2534.
[119] R. Gómez and M. J. Weaver, ''Electrochemical infrared studies of monocrystalline iridium surfaces. 3. Adsorbed nitric oxide and carbon monoxide as probes of Ir(100) interfacial structure'' Journal of Physical Chemistry B 1998, 102, 3754-3764.
[120] N. Hoshi, K. Kagaya and Y. Hori, ''Voltammograms of the single-crystal electrodes of palladium in aqueous sulfuric acid electrolyte: Pd(S)-[n(111)x(111)] and Pd(S)-[n(100)x(111)]'' Journal of Electroanalytical Chemistry 2000, 485, 55-60.
[121] N. Hoshi, M. Kuroda and Y. Hori, ''Voltammograms of stepped and kinked stepped surfaces of palladium: Pd(S)-[n(111) x (100)] and Pd(S)-[n(100) x (110)]'' Journal of Electroanalytical Chemistry 2002, 521, 155-160.
[122] F. G. Will, ''Hydrogen adsorption on platinum single crystal electrodes. I. Isotherms and heats of adsorption'' Journal of the Electrochemical Society 1965, 112, 451-455.
[123] A. T. Hubbard, R. M. Ishikawa and J. Katekaru, ''Study of platinum electrodes by means of electrochemistry and low energy electron diffraction. 2. Comparison of electrochemical activity of Pt(100) and Pt(111) surfaces'' Journal of Electroanalytical Chemistry 1978, 86, 271-288.
[124] E. Yeager, W. E. O'Grady, M. Y. C. Woo and P. Hagans, ''Hydrogen adsorption on single-crystal platinum'' Journal of the Electrochemical Society 1978, 125, 348-349.
[125] K. Yamamoto, D. M. Kolb, R. Koetz and G. Lehmpfuhl, ''Hydrogen adsorption and oxide formation on platinum single crystal electrodes'' Journal of Electroanalytical Chemistry 1978, 96, 233-239.
[126] B. Lang, R. W. Joyner and G. A. Somorjai, ''Low energy electron diffraction studies of high index crystal surfaces of platinum'' Surface Science 1972, 30, 440-453.
[127] C. Korzeniewski, V. Climent and J. M. Feliu, ''Electrochemistry at Platinum Single Crystal Electrodes'', in Electroanalytical Chemistry: A Series of Advances, vol. 24, A. J. Bard and C. Zoski (Eds.) CRC Press, Boca Ratón, 2012, pp. 75-169.
[128] V. Climent and J. M. Feliu, ''Thirty years of platinum single crystal electrochemistry'' Journal of Solid State Electrochemistry 2011, 15, 1297-1315.
[129] C. G. M. Hermse, A. P. van Bavel, M. T. M. Koper, J. J. Lukkien, R. A. van Santen and A. P. J. Jansen, ''Modelling the butterfly: (√3 x √7) ordering on fcc(111) surfaces'' Surface Science 2004, 572, 247-260.
[130] J. M. Feliu, J. M. Orts, R. Gómez, A. Aldaz and J. Clavilier, ''New information on the unusual adsorption states of Pt(111) in sulphuric acid solutions from potentiostatic adsorbate replacement by CO'' Journal of Electroanalytical Chemistry 1994, 372, 265-268.
[131] J. M. Orts, R. Gómez, J. M. Feliu, A. Aldaz and J. Clavilier, ''Potentiostatic charge displacement by exchanging adsorbed species on Pt(111) electrodes—acidic electrolytes with specific anion adsorption'' Electrochimica Acta 1994, 39, 1519-1524.
[132] N. García-Aráez, V. Climent, P. Rodríguez and J. M. Feliu, ''Thermodynamic analysis of (bi)sulphate adsorption on a Pt(111) electrode as a function of pH'' Electrochimica Acta 2008, 53, 6793-6806.
[133] N. García-Aráez, V. Climent, P. Rodríguez and J. M. Feliu, ''Elucidation of the Chemical Nature of Adsorbed Species for Pt(111) in H2SO4 Solutions by Thermodynamic Analysis'' Langmuir 2010, 26, 12408-12417.
[134] A. Wieckowski, E. R. Savinova and C. G. Vayenas, ''Catalysis and Electrocatalysis at Nanoparticle Surfaces'', Taylor & Francis, 2003.
[135] M. T. M. Koper, ''Fuel Cell Catalysis: A Surface Science Approach'', Electrocatalysis and Electrochemistry A. Wieckowski (Ed.), John Wiley & Sons, Hoboken, New Jersey, 2009.
[136] H. S. Liu, C. J. Song, L. Zhang, J. J. Zhang, H. J. Wang and D. P. Wilkinson, ''A review of anode catalysis in the direct methanol fuel cell'' Journal of Power Sources 2006, 155, 95-110.
Referencias
55
[137] S. E. F. Kleijn, S. C. S. Lai, M. T. M. Koper and P. R. Unwin, ''Electrochemistry of Nanoparticles'' Angewandte Chemie-International Edition 2014, 53, 3558-3586.
[138] R. Van Hardeveld and F. Hartog, ''Statistics of surface atoms and surface sites on metal crystals'' Surface Science 1969, 15, 189-230.
[139] N. Tian, Z. Y. Zhou and S. G. Sun, ''Platinum Metal Catalysts of High-Index Surfaces: From Single-Crystal Planes to Electrochemically Shape-Controlled Nanoparticles'' Journal of Physical Chemistry C 2008, 112, 19801-19817.
[140] J. Solla-Gullón, V. Montiel, A. Aldaz and J. Clavilier, ''Synthesis and electrochemical decontamination of platinum-palladium nanoparticles prepared by water-in-oil microemulsion'' Journal of the Electrochemical Society 2003, 150, E104-E109.
[141] M.-C. Daniel and D. Astruc, ''Gold Nanoparticles: Assembly, Supramolecular Chemistry, Quantum-Size-Related Properties, and Applications toward Biology, Catalysis, and Nanotechnology'' Chemical Reviews 2003, 104, 293-346.
[142] T. Nagaoka, T. Sakai, K. Ogura and T. Yoshino, ''Oxygen Reduction at electrochemically treated glassy-carbon electrodes'' Analytical Chemistry 1986, 58, 1953-1955.
[143] M. Boutonnet, J. Kizling, P. Stenius and G. Maire, ''The preparation of monodisperse colloidal metal particles from microemulsions'' Colloids and Surfaces 1982, 5, 209-225.
[144] T. S. Ahmadi, Z. L. Wang, A. Henglein and M. A. El-Sayed, ''"Cubic" colloidal platinum nanoparticles'' Chemistry of Materials 1996, 8, 1161-1163.
[145] A. López-Cudero, J. Solla-Gullón, E. Herrero, A. Aldaz and J. M. Feliu, ''CO electrooxidation on carbon supported platinum nanoparticles: Effect of aggregation'' Journal of Electroanalytical Chemistry 2010, 644, 117-126.
[146] J. Zhang and J. Fang, ''A general strategy for preparation of Pt 3d-transition metal (Co, Fe, Ni) nanocubes'' Journal of the American Chemical Society 2009, 131, 18543-18547.
[147] D. Li, C. Wang, D. Tripkovic, S. Sun, N. M. Markovic and V. R. Stamenkovic, ''Surfactant removal for colloidal nanoparticles from solution synthesis: The effect on catalytic performance'' ACS Catalysis 2012, 2, 1358-1362.
[148] S. I. Choi, S. Xie, M. Shao, J. H. Odell, N. Lu, H. C. Peng, L. Protsailo, S. Guerrero, J. Park, X. Xia, J. Wang, M. J. Kim and Y. Xia, ''Synthesis and characterization of 9 nm Pt-Ni octahedra with a record high activity of 3.3 A/mg Pt for the oxygen reduction reaction'' Nano Letters 2013, 13, 3420-3425.
[149] J. Y. Park, C. Aliaga, J. R. Renzas, H. Lee and G. A. Somorjai, ''The Role of Organic Capping Layers of Platinum Nanoparticles in Catalytic Activity of CO Oxidation'' Catalysis Letters 2009, 129, 1-6.
[150] J. Clavilier, R. Albalat, R. Gómez, J. M. Orts, J. M. Feliu and A. Aldaz, ''Study of the charge displacement at constant potential during CO adsorption on Pt(110) and Pt(111) electrodes in contact with a perchloric acid solution'' Journal of Electroanalytical Chemistry 1992, 330, 489-497.
[151] V. Climent, R. Gómez and J. M. Feliu, ''Effect of increasing amount of steps on the potential of zero total charge of Pt(111) electrodes'' Electrochimica Acta 1999, 45, 629-637.
[152] J. Solla-Gullón, V. Montiel, A. Aldaz and J. Clavilier, ''Electrochemical characterization of platinum nanoparticles prepared by microemulsion: How to clean them without loss of crystalline surface structure'' Journal of Electroanalytical Chemistry 2000, 491, 69-77.
[153] E. Herrero, L. J. Buller and H. D. Abruña, ''Underpotential deposition at single crystal surfaces of Au, Pt, Ag and other materials'' Chemical Reviews 2001, 101, 1897-1930.
[154] D. M. Kolb, ''Physical and electrochemical properties of metal monolayers on metallic substrates'', in Advances in Electrochemistry and Electrochemical Engineering, vol. 11, Wiley, New York, 1978, pp. 125-271.
[155] V. Climent, N. García-Aráez and J. M. Feliu, ''Clues for the Molecular-Level Understanding of Electrocatalysis on Single-Crystal Platinum Surfaces Modified by p-Block Adatoms'', in Fuel Cells
Capítulo 1: Síntesis
56
Catalysis. A Surface Science Approach, M. T. M. Koper (Ed.) Wiley, Hoboken, New Jersey, 2009, pp. 209-244.
[156] J. Clavilier, J. M. Feliu, A. Fernández-Vega and A. Aldaz, ''Electrochemical behavior of Irreversibly Adsorbed Bismuth on Pt (100) with Different Degrees of Crystalline Surface Order'' Journal of Electroanalytical Chemistry 1989, 269, 175-189.
[157] F. J. Vidal-Iglesias, R. M. Arán-Ais, J. Solla-Gullón, E. Herrero and J. M. Feliu, ''Electrochemical Characterization of Shape-Controlled Pt Nanoparticles in Different Supporting Electrolytes'' ACS Catalysis 2012, 2, 901-910.
[158] R. M. Arán-Ais, F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero and J. M. Feliu, ''Electrochemical characterization of clean shape-controlled Pt nanoparticles prepared in presence of oleylamine/oleic acid'' Electroanalysis 2015, 27, 945-956.
[159] J. Solla-Gullón, F. J. Vidal-Iglesias, E. Herrero, J. M. Feliu and A. Aldaz, ''CO monolayer oxidation on semi-spherical and preferentially oriented (100) and (111) platinum nanoparticles'' Electrochemistry Communications 2006, 8, 189-194.
[160] J. Solla-Gullón, F. J. Vidal-Iglesias, A. López-Cudero, E. Garnier, J. M. Feliu and A. Aldaz, ''Shape-dependent electrocatalysis: methanol and formic acid electrooxidation on preferentially oriented Pt nanoparticles'' Physical Chemistry Chemical Physics 2008, 10, 3689-3698.
[161] Z.-Y. Zhou, Q. Wang, J.-L. Lin, N. Tian and S.-G. Sun, ''In situ FTIR spectroscopic studies of electrooxidation of ethanol on Pd electrode in alkaline media'' Electrochimica Acta 2010, 55, 7995-7999.
[162] M. López-Atalaya, E. Morallón, F. Cases, J. L. Vázquez and J. M. Pérez, ''Electrochemical oxidation of ethanol on Pt(hkl) basal surfaces in NaOH and Na2CO3 media'' Journal of Power Sources 1994, 52, 109-117.
[163] S. C. S. Lai and M. T. M. Koper, ''Ethanol electro-oxidation on platinum in alkaline media'' Physical Chemistry Chemical Physics 2009, 11, 10446-10456.
[164] S. Chumillas, C. Busó-Rogero, J. Solla-Gullón, F. J. Vidal-Iglesias, E. Herrero and J. M. Feliu, ''Size and diffusion effects on the oxidation of formic acid and ethanol on platinum nanoparticles'' Electrochemistry Communications 2011, 13, 1194-1197.
[165] S. P. E. Smith, K. F. Ben-Dor and H. D. Abruña, ''Structural effects on the oxidation of HCOOH by bismuth-modified Pt(111) electrodes with (100) monatomic steps'' Langmuir 1999, 15, 7325-7332.
[166] F. J. Vidal-Iglesias, A. López-Cudero, J. Solla-Gullón, A. Aldaz and J. M. Feliu, ''Pd-Modified Shape-Controlled Pt Nanoparticles Towards Formic Acid Electrooxidation'' Electrocatalysis 2012, 3, 313-323.
[167] K. Bergamaski, E. R. Gonzalez and F. C. Nart, ''Ethanol oxidation on carbon supported platinum-rhodium bimetallic catalysts'' Electrochimica Acta 2008, 53, 4396-4406.
[168] C. Lamy, S. Rousseau, E. M. Belgsir, C. Coutanceau and J. M. Léger, ''Recent progress in the direct ethanol fuel cell: development of new platinum-tin electrocatalysts'' Electrochimica Acta 2004, 49, 3901-3908.
[169] M. E. Paulino, L. M. S. Nunes, E. R. Gonzalez and G. Tremiliosi-Filho, ''In situ FTIR spectroscopic study of ethanol oxidation on Pt(111)/Rh/Sn surface. The anion effect'' Electrochemistry Communications 2015, 52, 85-88.
[170] A. O. Neto, R. R. Dias, M. M. Tusi, M. Linardi and E. V. Spinacé, ''Electro-oxidation of methanol and ethanol using PtRu/C, PtSn/C and PtSnRu/C electrocatalysts prepared by an alcohol-reduction process'' Journal of Power Sources 2007, 166, 87-91.
[171] A. Crown, I. R. Moraes and A. Wieckowski, ''Examination of Pt(111)/Ru and Pt(111)/Os surfaces: STM imaging and methanol oxidation activity'' Journal of Electroanalytical Chemistry 2001, 500, 333-343.
Referencias
57
[172] V. Pacheco Santos and G. Tremiliosi-Filho, ''Effect of osmium coverage on platinum single crystals in the ethanol electrooxidation'' Journal of Electroanalytical Chemistry 2003, 554–555, 395-405.
[173] Q. G. He, B. Shyam, K. Macounova, P. Krtil, D. Ramaker and S. Mukerjee, ''Dramatically Enhanced Cleavage of the C-C Bond Using an Electrocatalytically Coupled Reaction'' Journal of the American Chemical Society 2012, 134, 8655-8661.
[174] P. A. Christensen, S. W. M. Jones and A. Hamnett, ''An in situ FTIR spectroscopic study of the electrochemical oxidation of ethanol at a Pb-modified polycrystalline Pt electrode immersed in aqueous KOH'' Physical Chemistry Chemical Physics 2013, 15, 17268-17276.
Capítulo 2: Efecto de la estructura superficial y del anión para la
oxidación de etanol en nanopartículas de platino
61
Capítulo 2: Efecto de la estructura superficial y del anión
para la oxidación de etanol en nanopartículas de platino
RESUMEN
Este trabajo busca comprobar si el efecto de la estructura superficial y el anión
adsorbido en la oxidación de etanol, observados en electrodos monocristalinos de platino,
son extrapolables a las nanopartículas de platino con orientación preferencial. Para ello, se
analizan en primer lugar los perfiles voltamétricos para la oxidación de 0.2 M CH3CH2OH
en disoluciones 0.5 M H2SO4 y 0.1 M HClO4 en los planos base del platino, siendo el
potencial al cual comienza la oxidación de etanol el indicador acerca de cuál es la
superficie en la que se produce más CO procedente de la rotura del enlace C-C del etanol.
Concretamente, el electrodo Pt(110) y, sobre todo, el Pt(100) se muestran activos para la
formación de CO, lo cual concuerda con la histéresis observada entre el barrido positivo y
negativo de potenciales después de oxidar el CO a CO2 a potenciales elevados. Por el
contrario, en el electrodo Pt(111) la histéresis es casi nula, mostrando la ausencia
significativa de veneno y la preferencia por la ruta de la oxidación incompleta hasta ácido
acético.
En cuanto al efecto de la adsorción del anión, se espera que cuando el anión sulfato
esté presente en la disolución, las corrientes de oxidación sean menores que al utilizar
ácido perclórico como electrolito soporte, debido a que la adsorción competitiva entre el
reactivo y los aniones sulfato debe provocar una disminución en la actividad para la
oxidación de etanol. Sin embargo, en los electrodos Pt(100) y Pt(110), la actividad es
similar en ambos casos, asignándose dicho efecto a la adsorción de aniones acetato sobre
platino. Como la adsorción de acetato tiene una fuerza similar a la de los aniones sulfato,
esto resulta en corrientes similares en medio perclórico y sulfúrico. Únicamente en el caso
del Pt(111), superficie donde la adsorción de los aniones sulfato es más estable debido a la
formación de una estructura ordenada asociada a dominios bidimensionales muy extensos,
las corrientes son menores empleando H2SO4 como electrolito soporte.
Capítulo 2: Efectos de la estructura superficial y del anión para la oxidación de etanol en nanopartículas de platino
62
Al cambiar a las nanopartículas de platino con orientación preferencial, lo primero
que se realiza es la caracterización electroquímica en 0.5 M H2SO4 para comprobar las
formas predominantes en cada muestra mediante el perfil voltamétrico. Por otra parte,
previo al análisis de las curvas, se comprueba que la oxidación de etanol no se ve afectada
por problemas de aglomeración de nanopartículas, lo que impediría la correcta difusión del
etanol hacia todo el depósito de las nanopartículas de platino. Por ello, se trabaja en todo
momento con cantidades bajas de platino (entre 0.05 y 0.1 cm2 de área superficial activa de
Pt) y se comprueba siempre que la corriente de pico de oxidación de etanol es directamente
proporcional a la cantidad total de nanopartículas tras realizar varios depósitos sucesivos
de platino. Al estudiar la oxidación de etanol con las nanopartículas de platino en las
mismas condiciones que en las superficies monocristalinas de platino, se confirman las
tendencias observadas en cuanto a las corrientes de oxidación y los potenciales de inicio de
la oxidación de etanol observados con los planos basales del platino. Se obtiene que las
nanopartículas (100)Pt son más activas para la formación de CO mientras que las muestras
(111)Pt favorecen la formación de ácido acético. Además, no se observa efecto relacionado
con la adsorción del sulfato en la oxidación de etanol debido a la alta cantidad de ácido
acético formado, incluso para las nanopartículas (111)Pt. Esto es debido a que los
dominios con orientación cristalográfica 111 en estas muestras son pequeños,
provocando que el efecto de la adsorción del sulfato sea menor que en el caso de los
electrodos monocristalinos.
Por último, se realizaron experimentos de IR en configuración de reflexión externa
para confirmar las suposiciones realizadas a partir de las corrientes de oxidación y del
potencial al cual se inicia la oxidación en las voltametrías. Los experimentos se realizaron
en una disolución 0.2 M CH3CH2OH pero con una menor concentración de electrolito
soporte, 0.1 M H2SO4, para impedir posibles daños en el prisma de CaF2. Las bandas
detectadas se asignaron de acuerdo con lo establecido en la Tabla 2.1, viéndose claramente
las bandas asociadas a la reacción de oxidación de etanol, como son las del CO adsorbido,
la de formación de CO2 y la de producción de acetato. La comparación directa entre los
distintos experimentos IR no es sencilla debido a las diferentes condiciones de trabajo del
espectrómetro en cada experimento. Por este motivo, la comparación se realiza
normalizando las bandas de CO lineal y de CO2 respecto a una de las bandas del producto
ácido acético a 0.9 V. Como era de esperar, las superficies (100)Pt son las más favorables a
Resumen
63
la formación de CO, mientras que las superficies (111)Pt son muy inactivas para la rotura
del enlace C-C. En cuanto a la oxidación completa hasta CO2, la muestra que exhibe un
mejor comportamiento es la de las nanopartículas (poly)Pt, ya que las muestras (100)Pt
presentan un exceso de formación de CO.
65
Chapter 2
This chapter has been adapted and formatted from Journal of Materials Chemistry A, 2013, 1, 7068-7076.
Corresponding author: [email protected]
Chapter 2: Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles
66
2.1 Introduction
Many electrochemical reactions are structure sensitive, that is to say, depending on
how the atoms are arranged at the catalyst surface, the catalytic activity changes. In this
way, by studying a given reaction with the different basal planes, the effect of the surface
structure can be analyzed and understood. Unfortunately, from an applied point of view,
single crystals cannot be used and real catalysts are normally dispersed in the form of
nanoparticles. However, the effect of the arrangement of the atoms at the surface is still
valid for nanoparticles catalysts, and therefore, the fact that many electrocatalytic reactions
are structure sensitive or site demanding [1-6] makes the control over the surface structure
of the nanoparticle an issue of paramount importance. In this sense, we have extensively
studied the influence of the nanoparticles’ surface structure in relevant reactions such as
oxygen reduction, or oxidation of different molecules such as carbon monoxide, ammonia,
methanol or formic acid [7-15]. However the effect of the surface structure with
nanoparticles towards ethanol oxidation still remains unexplored.
Ethanol oxidation has received wide attention because of its possible use in fuel
cells, since it can be easily produced from biomass and has a high energy density (12
electrons are exchanged in a complete oxidation to CO2). However, incomplete oxidation
and the high overpotentials required for the reaction reduce its potential applicability. On
platinum electrodes, ethanol oxidation occurs in a dual path mechanism [16, 17]:
(2.1)
Pathway (1)-(2) shows the incomplete ethanol oxidation to yield first acetaldehyde
with two electrons transferred and secondly, acetic acid, transferring two additional
electrons. This incomplete oxidation route is not propitious because it yields lower energy
density and the formation at the electrode of a stable product (acetic acid) which is very
difficult to oxidize to CO2 [18]. The preferred paths for the oxidation are those leading to
the formation of CO2, which requires the cleavage of the C-C bond. This cleavage can
occur either in the ethanol molecule (reaction (4)) or in the acetaldehyde molecule
Introduction
67
(reaction (3)) and leads to the formation of different fragments that eventually evolve to
form adsorbed CO. By means of IR experiments, the different reaction intermediates and
products can be identified. Due to the strong adsorbing properties of CO on platinum and
the large overpotential required for its oxidation, it has been considered as a poison by
some authors [19-21]. However, it can be argued that CO is not a poisoning specie but a
true active intermediate, the formation of which is required for the complete oxidation of
the molecule to CO2 [16, 22, 23]. With the aim of achieving the complete oxidation of
ethanol, by facilitating the cleavage of the C-C bond and the oxidation of adsorbed CO,
different strategies have been used. Thus, different adatoms such as Ru, Sn or Rh have
been used to decorate the platinum surface of the catalyst [24-29]. In addition, a further
improvement of the activity can be obtained with the use of ternary catalysts [30-34].
Regarding the importance of the surface structure, it is well known that the ethanol
oxidation mechanism depends on this parameter. The low reactivity of the Pt(100)
electrode in the positive going scan at lower potentials is mainly a consequence of CO
adsorption on the electrode surface. On the other hand, CO formation on the Pt(111)
electrode is almost negligible being acetaldehyde and acetic acid the main products of its
oxidation. Finally, Pt(110) has an intermediate behavior between that of Pt(100) and
Pt(111). Additionally, the presence of adsorbed anions can decrease current densities due
to a competitive adsorption of anions and reactants [19].
In the present paper, we report the influence of the surface structure/shape of well
characterized bare Pt nanoparticles on ethanol electrooxidation reaction. The aim is to
establish links between the activity reported for well-defined surface structures (basal
planes) and that of preferentially oriented Pt nanoparticles. In addition, we also study the
effect of anion adsorption on ethanol oxidation.
Chapter 2: Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles
68
2.2 Experimental
Platinum single crystal electrode surfaces were prepared from small single crystal
beads, ca. 2 mm in diameter following the method developed by Clavilier et al. [35].
Before any experiment, working electrodes were annealed for around 30 s in a gas-oxygen
flame, cooled down in a reductive atmosphere (H2 + Ar) and quenched in ultrapure water
in equilibrium with this atmosphere [36]. Then, the electrodes were transferred to a cell
under the protection of a droplet of deoxygenated water for further characterization.
Four different types of nanoparticles were used. The synthetic details of the different
Pt nanoparticles as well as the characterization of their shape and particle size distribution
have been previously reported [7, 11, 12, 37-39]. In brief, the quasi spherical polyoriented
nanoparticles, denoted as (poly)Pt, were synthesized by the water-in-oil microemulsion
method [40, 41] (water (3%) / polyethylene glycol dodecyl ether (Brij®30) (16.5%) / n-
heptane (80.5%)), using sodium borohydride as the reducing agent. The concentration of
H2PtCl6 in the water phase was 0.1 M. Reduction was performed by directly adding NaBH4
(10 times the stoichiometric amount) to the micellar solution. After reduction was
complete, nanoparticles were cleaned using acetone and ultrapure water [41]. With this
cleaning procedure, nanoparticles were cleaned while the initial surface structure of the
nanoparticles remained.
On the other hand, the terms (100)Pt, (111)Pt and (100)-(111)Pt nanoparticles
correspond to the samples prepared using a colloidal method [37, 42]. These nanoparticles
have a preferential surface orientation, for which the predominant ordered domain at
surface corresponds to 100, 111 and a mixture of 100 and 111 domains,
respectively. For their synthesis 0.5 ml of 0.1 M sodium polyacrylate solution (Mw = 2100)
was added to 100 ml of an aged 10-4 M solution containing the desired Pt precursor. As the
Pt source, K2PtCl4 was employed for the synthesis of (100)Pt nanoparticles, whereas
H2PtCl6 was used for the (100)-(111)Pt and (111)Pt nanoparticles. The concentration ratio
of K2PtCl4 or H2PtCl6 to polyacrylate was 1:5. In addition, in the case of (100)-(111)Pt and
(111)Pt nanoparticles, the pH of the solution was adjusted to 7 with 0.1 M HCl, whereas in
the case of (100)Pt the pH was not adjusted. Finally, the solutions were purged with Ar for
20 min and Pt ions were reduced by bubbling H2 for 5 min, except in the case of (111)Pt
Experimental
69
where only 5 min of Ar bubbling and 1 min of H2 bubbling were used. Then, the reaction
vessel was sealed and the solution was left overnight. Once reduction was complete (12–14
h) two NaOH pellets were added to produce the precipitation of the nanoparticles. After
complete precipitation, the nanoparticles were washed 3–4 times with ultrapure water. The
predominant size of the nanoparticles was 4 nm for the (poly)Pt and 8-10 nm for the
colloidal nanoparticles.
The Pt nanoparticles electrodes were prepared by depositing the dispersed Pt
nanoparticles on a hemispherical polycrystalline gold substrate (ca. 3 mm2) from a solution
droplet ranging from 0.5 to 1.5 µL and drying under Ar atmosphere. The procedures used
for the electrochemical cleaning of the different Pt nanoparticles have been described
previously [37, 40, 41]. They involve, in the final step, a CO adsorption and stripping
treatment, a process that does not perturb significantly the platinum surface order.
Voltammetric curves were first recorded in a 0.5 M H2SO4 or 0.1 M HClO4 solution,
in order to measure the active surface area of the Pt nanoparticles. The charge involved in
the hydrogen and anion adsorption/desorption region, after the subtraction of apparent
double layer contribution, was used assuming that the charge density for this region is 230
µC cm-2 in sulfuric acid solution and 200 µC cm-2 in perchloric acid solution [43].
Depending on the supporting electrolyte used, experiments for ethanol oxidation were
carried out in 0.5 M H2SO4 + 0.2 M CH3CH2OH or in 0.1 M HClO4 + 0.2 M CH3CH2OH.
Spectroelectrochemical experiments were performed with a Nicolet Magna 850
spectrometer equipped with a narrow-band mercury cadmium telluride (MCT) detector.
The spectroelectrochemical cell had a prismatic CaF2 window beveled at 60º [44, 45]. The
IR spectra were collected with p-polarized light with a resolution of 8 cm-1. For each
spectrum, 100 interferograms were added to increase the signal-to-noise ratio. The spectra
are presented as the value (R1-R2)/R1, where R2 and R1 are the reflectance values
corresponding to the single beam spectra recorded at the sample and reference potentials,
respectively. The reference spectrum was acquired at 0.1 V whereas the sample spectra
were recorded after applying successive potential steps of 100 mV in the positive direction
from 0.1 to 0.9 V vs. the reversible hydrogen electrode (RHE). Positive bands in the
spectra correspond to species that have been formed at the sampling potential (or with an
Chapter 2: Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles
70
increase in concentration) whereas negatives bands are associated with a diminution of the
concentration of the species. The experimental protocol for performing FTIR experiments
with the Pt nanoparticle electrodes was identical to that used in the voltammetric
experiments.
All experiments were carried out at room temperature in a typical three-electrode
electrochemical cell. A gold wire was used as a counter-electrode and a reversible
hydrogen (N50, Air Liquide) electrode (RHE) was used as a reference. Solutions were
prepared from sulfuric acid (Merck 95-97% GR for analysis), perchloric acid (Merck 60%
for analysis), ethanol (Merck p.a.) and ultra-pure water (Elga-Purelab Ultra 18.2 MΩ cm).
Argon (N50, Air Liquide) was used for deoxygenating all the solutions and CO (N47, Air
Liquide) for the aforementioned final cleaning step of the nanoparticles.
Results and discussion
71
2.3 Results and discussion
2.3.1 Ethanol oxidation on single crystal electrodes
The voltammetric profiles of ethanol oxidation for Pt single crystal electrodes are
presented in Fig. 2.1, using sulfuric acid and perchloric acid as a supporting electrolytes in
the same concentration that will be used for the voltammetric experiments with platinum
nanoparticles. The upper limit potential has thoughtfully been adjusted to 0.95 V to avoid
significant changes in the surface structure of the electrodes due to oxide formation and its
subsequent reduction while allowing the removal of all the CO adsorbed on the surface. In
the presence of ethanol, the voltammetric profiles are stable, with only minor changes in
the oxidation currents upon cycling, mainly in the positive going scan. For that reason, the
first cycle is reported in the figure. In general, CO is formed at low potentials in the
positive going scan as a result of the cleavage of the C-C bond of the ethanol molecule
[46]. The adsorption of CO blocks the surface and causes a low activity for the ethanol
oxidation at low potentials. At higher potentials (above 0.7 V), CO is oxidized and the
surface regains its activity for the oxidation of ethanol. For the Pt(100) electrode, this
behavior is very clear, since the current below 0.7 V in the positive going scan is negligible
and a sharp increase is observed at 0.7 V.
On the other hand, the Pt(111) electrode shows the opposite behavior. Currents in the
positive and negative going scans are very similar, due to the very low CO formation rate
on this surface. In fact, the CO formation on Pt(111) has been linked to the presence of
defects [20, 46]. Finally, the Pt(110) electrode shows an intermediate behavior between
that of Pt(111) and Pt(100) regarding the amount of CO formed. Taking into account the
currents measured at low potentials, i.e., below 0.5 V, the trend observed for the activity of
the electrodes is the following: Pt(100) < Pt(110) < Pt(111). However, when maximum
currents are taken into account the order becomes Pt(111) < Pt(110) < Pt(100), as has been
reported in the past [47]. Regarding the final product in the oxidation process, acetic acid is
the major product for the three basal planes [19]. However, the yield of CO2 is the highest
for the Pt(100) while the Pt(111) electrode produces acetic acid almost exclusively.
Chapter 2: Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles
72
Fig. 2.1. Voltammetric profiles for ethanol oxidation (1stcycle) on Pt(100), Pt(110) and Pt(111)
electrodes in 0.5 M H2SO4 + 0.2 CH3CH2OH (black line) and 0.1 M HClO4 + 0.2 M CH3CH2OH (red line).
Sweep rate: 50 mV s-1.
The effect of the sulfate anion adsorption in the voltammetric profile is also shown in
Fig. 2.1. In general, it is expected that currents in perchloric acid solutions are higher than
those measured in sulfuric acid solutions, owing to the specific adsorption of sulfate. This
is mainly due to a competitive adsorption of the reactant and sulfate anions at the surface
of the electrode. However, previous results comparing 0.1 M H2SO4 and 0.1 M HClO4
showed similar currents in both media [19]. Previous contributions ascribed this lower than
expected activity in perchloric acid to the adsorption of acetate [19, 48]. In fact, when the
comparison is made between 0.1 M HClO4 and 0.5 M H2SO4 (Fig. 2.1), similar current
densities are also obtained for the Pt(110) and Pt(100) electrodes, which indicates that the
higher sulfate concentration in comparison with that of the previous contribution [19] has
no major effect in the currents for those electrodes.
0
2
4
6
80.0 0.2 0.4 0.6 0.8 1.0
E vs RHE/V
j/mA
cm-2
Pt(100)
0
2
4
6Pt(110)
j/m
A cm
-2
0.0 0.2 0.4 0.6 0.8 1.00
2
4
6Pt(111)
j/mA
cm-2
E vs RHE/V
0.0 0.5 1.0
0.0
0.5
1.0
1.5
j/mA
cm-2
E vs RHE/V
Results and discussion
73
On the other hand, the currents in sulfuric acid for the Pt(111) electrode are
significantly lower than those in 0.1 M HClO4 or 0.1 M H2SO4, which implies a significant
effect of the sulfate concentration for this electrode. It should be borne in mind that the
adsorption of sulfate on the Pt(111) electrode is significantly stronger than that on the
Pt(100) electrode [49] and that sulfate forms an ordered adlayer. The stronger sulfate
adsorption and the increase in stability of the adlayer, due to the formation of the ordered
structure, results in a significant effect of the anion on the oxidation currents. Similar
effects have been observed, for example, for oxygen reduction [50]. In the absence of such
an ordered adlayer, it would be expected that the currents in sulfuric and perchloric acid
were similar, as for the other studied electrodes. In short, the formation of acetic acid,
which adsorbs as acetate on the electrode surface above 0.3-0.4 V, implies that the
electrode surface at the potentials where ethanol oxidation takes place is always covered
with a layer of adsorbed anions. In perchloric acid solutions, the adsorbed adlayer is made
of acetate anions, whereas in sulfuric acid, the adlayer is formed by a mixture of acetate
and sulfate anions. In this way, ethanol always competes with an adlayer of the similar
strength, regardless of the supporting electrolyte (sulfuric or perchloric acid) and then,
oxidation currents are similar.
2.3.2 Electrochemical characterization of Pt nanoparticles
Fig. 2.2 shows the voltammetric profiles of the different nanoparticles in 0.5 M
sulfuric acid solution. A detailed analysis of the relationship between the voltammetric
profile and the surface structure of the nanoparticles has been carried out previously [37,
39]. A brief summary of the main characteristics is reported here. A typical polycrystalline
platinum electrode presents two main peaks at 0.125 and 0.265 V. The peak at 0.125 V is
linked to the presence of 110 sites, whereas that at 0.265 is due to the presence of 100
defects on 111 domains and 100 short domains. This typical shape is observed for the
(poly)Pt sample (Fig. 2.2A), which has no preferential orientation on the surface.
Chapter 2: Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles
74
Fig. 2.2. Cyclic voltammetry for the (poly)Pt (red line), (100)Pt (green line), (100)-(111)Pt (blue line)
and (111)Pt (orange line) nanoparticles used in this work in 0.5 M H2SO4. Scan rate: 50 mV s-1.
When the surface structure presents a preferential orientation, additional features in
the voltammogram can be observed. Large 100 ordered domains give rise to a peak at
0.37 V, as it is observed for (100)-(111)Pt and specially for the (100)Pt nanoparticles.
Besides, adsorption of sulfate on 111 ordered domains gives rise to a wide signal around
0.5 V, which can be observed on the (111)Pt and on the (100)-(111)Pt nanoparticles. In
addition, voltammetric peaks are sharp and reversible, showing the cleanliness of the
nanoparticles’ surface and indicating that chemicals from the synthesis process have been
successfully removed. A similar analysis can also be made in HClO4 (results not shown),
although as it is known the adsorption desorption peaks are not as well resolved as in
sulfuric acid. Different voltammetric profiles can also be obtained from the distinct shape
of the nanoparticles [39, 43].
2.3.3 Ethanol oxidation on Pt nanoparticles.
Previous studies have demonstrated that the electrocatalytic results measured for a
given nanoparticle sample can be erroneously interpreted depending on the nanoparticle
Results and discussion
75
loading [51]. Large loadings may display a lower electrocatalytic activity than that
expected. In this situation, a large amount of the reactant arriving from the solution to the
electrode is consumed in the outermost part of the nanoparticle deposit, so that the inner
part remains inactive (or nearly) due to the lack of reactants. However, when the active
area is measured using the hydrogen adsorption/desorption process by cyclic voltammetry,
those diffusion problems are negligible and therefore the whole sample contributes to the
total area. Under these circumstances, the calculation of the current density uses an
incorrect area, because part of the measured area is not taking part in the reaction. As a
result, the reported current densities for the studied reaction are, erroneously, significantly
lower than those that would have been obtained in absence of diffusion problems through
the nanoparticle deposit, and possible catalytic enhancements can remain hidden because
of this situation [51].
Thus, if the electrocatalytic activity of the nanoparticles has to be assessed, the
experiments have to be designed in such a way that there are no diffusion problems in the
nanoparticles deposit. In order to check it, the active surface area of a deposit was
determined in a sulfuric acid solution and the current for ethanol oxidation was measured.
After that, a second deposit was made on top of the first one, and the active area and
currents for ethanol oxidation were once again measured.
For the experimental conditions used in this work, it was found that the current for
ethanol oxidation was directly proportional to the active area of the electrode (Fig. 2.3),
that is to say, the current density for ethanol oxidation is the same for the two different
nanoparticles loadings. This proportionality ensures, while working for areas below that of
the second deposit, the correct calculation of the current densities for ethanol oxidation
experiments. This proportionality was obtained for the different samples used in this study
in order to be sure of working inside the limits to obtain correct current density values. In
addition, it should be mentioned that this proportionality disappears when larger deposits
are made.
Chapter 2: Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles
76
Fig. 2.3. (A) Voltammograms corresponding to two successive deposits of (111)Pt nanoparticles in
H2SO4. Sweep rate: 50 mV s-1. (B) Ethanol oxidation peak current plot vs hydrogen charge plot.
The voltammetric profiles for ethanol oxidation (first cycle) for the different types of
Pt nanoparticles in 0.2 M CH3CH2OH both in 0.5 M H2SO4 and 0.1 M HClO4 are shown in
Fig. 2.4. As aforementioned, the upper potential limit was set at 0.95 V in order to avoid
structural modifications due to oxide formation/reduction cycles. In all cases, the
voltammetric profiles show an oxidation peak at 0.8-0.85 V in the positive going scan and
higher oxidation currents in the negative going scan. For the (100)Pt nanoparticles, a
prominent peak in the positive going scan at 0.8-0.85 V is obtained and is associated with
the oxidation of the CO layer formed from the cleavage of the C-C bond at low potentials
and the re-activation of the surface for the oxidation of ethanol [19], in a similar way to
that observed for the Pt(100) single crystal in Fig. 2.1. This type of contribution is absent
in the other two basal planes. Therefore, the peak observed for the nanoparticles at this
potential is then clearly related to the presence of 100 domains on the nanoparticles. As
expected, the current density is maximum for the (100)Pt nanoparticles, whereas (111)Pt
nanoparticles, which have a very low amount of 100 ordered domains on the surface,
show the lowest current density in this potential region. In addition, (poly)Pt and (100-
111)Pt nanoparticles, which have an intermediate amount of 100 ordered domains, have
intermediate current values in this potential region.
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.90.000
0.001
0.002
0.003
0.004
0.005
0.006
0.007B
I/mA
E vs RHE/V
A
0 2 4 6 8 10 12
0
20
40
60
80
100
I peak
bac
kwar
d sc
an/µ
A
QH/µC
R2=0.99461
Results and discussion
77
Fig. 2.4. Ethanol oxidation (1st cycle) on (A) (poly)Pt, (B) (100)Pt, (C) (100)-(111)Pt and (D) (111)Pt
nanoparticles in 0.5 M H2SO4 + 0.2 M CH3CH2OH (black line) and 0.1 M HClO4 + 0.2 M CH3CH2OH (red
line). Sweep rate: 50 mV s-1.
Another trend observed for the platinum basal planes which is also replicated by the
nanoparticles is the dependence of the onset potential for the oxidation of ethanol with the
surface structure. In this sense, Pt(111) shows the lowest value, and the difference in the
currents between the negative and positive-going scans is also the lowest for this basal
plane. In this way, current densities for nanoparticles electrodes at 0.4 V, in the positive-
going sweep, are 109.8, 76.8, 125.5 and 139.6 μA cm-2 corresponding to (poly), (100),
(100)-(111) and (111)Pt nanoparticles respectively. As it is observed, the higher the
amount of (111) sites, the higher the current density recorded at this potential. The lower
current density is evidently obtained for the (100)Pt nanoparticles, as the 100 sites are,
as formerly explained, covered by CO. As in the previous case, this contribution can give
qualitative information about the amount of 111 sites at the nanoparticles surface.
Chapter 2: Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles
78
In order to get insight into the role played by the competitive adsorption of sulfate
anions in ethanol oxidation with Pt nanoparticles, the same voltammetric experiments were
repeated with the same ethanol concentration but in 0.1 M HClO4. The resulting
voltammograms are compared to those obtained in sulfuric acid solutions in Fig. 2.4. The
results agree with the experiments performed by Colmati et al. [19], where the adsorption
of anions has nearly no effect on the oxidation reaction. This fact implies that the amount
of acetic acid formed is significantly high, so that acetate can adsorb on the surface and
compete with ethanol for the adsorption sites. It is worth mentioning that the currents
measured for the (111)Pt nanoparticles in 0.1 M HClO4 and in 0.5 M H2SO4 are almost
identical, unlike the behavior observed for the Pt(111) electrode. As previously mentioned,
the difference arises from the fact that sulfate on very long range ordered 111 domains
forms an ordered structure, which increases the stability of the adlayer [52, 53], and
significantly diminishes the currents for the oxidation of ethanol and other organic
molecules on the Pt(111) electrode. Nevertheless, such order structure is not observed for
small 111 domains [52], such as those present on the surface of the nanoparticles and,
thus, currents in both media are similar.
2.3.4 FTIR experiments of ethanol oxidation.
With the aim of determining the final products of the ethanol oxidation reaction and
their relative ratio, FTIR experiments were carried out. In this case, 0.1 M H2SO4 solution
was used as the supporting electrolyte as because of higher acid concentrations can damage
the prism. Despite the different anion concentration, no differences in the results are
expected due to the effective insensitivity of the oxidation currents to the presence of
perchlorate or sulfate anions in the solution. On the other hand, the ethanol concentration
was the same as in the previous experiments. Table 2.1 summarizes the frequencies of the
observed bands in the different spectra and the vibrational modes of the molecules
associated with these bands [18, 20, 54].
Results and discussion
79
υH2O/cm-1 Functional group
Mode
2340 CO2 O-C-O asymmetric stretching
2030-2070 Adsorbed CO Linearly bonded
1715 COOH or CHO C=O stretching
1400 Adsorbed
–COO-
C-O symmetric stretching
1280 COOH Coupling C-O stretching + OH deformation
1210 Adsorbed
(bi)sulfate
Table 2.1. Observed IR frequencies in the spectra for ethanol oxidation in H2O.
Fig. 2.5 and 2.6 show the IR spectra for the ethanol oxidation reaction on the
different platinum nanoparticles. In general, there are no qualitative differences in the
spectra for the different nanoparticles. The small band around 2050 cm-1, which is clearly
observed above 0.3 V, indicates the presence of adsorbed linear CO. This band grows as
the potential increases up to ca. 0.7 V, where CO is oxidized and then bands at 2340 cm-1,
corresponding to the formation of CO2, start to appear. At 0.9 V, the band corresponding to
CO is negative, in particular for the (100)Pt nanoparticles, demonstrating that adsorbed
linear CO is present at the reference potential, that is, at 0.1 V. The presence of adsorbed
CO at 0.1 V shows that the cleavage of the C-C bond of the ethanol molecule takes place at
low potentials, as in the case of single crystal electrodes [46]. At potentials above the onset
of oxidation of CO to CO2, the bands associated with the formation of acetic acid are
clearly visible at 1400 and 1280 cm-1. Although no bands can be observed due to the
presence of acetaldehyde, its formation cannot be discarded. It should be highlighted that
bands associated with acetaldehyde are less intense and appear in the same frequency
region as those corresponding to acetic acid, and for that reason, are difficult to resolve.
Additionally, the band corresponding to the stretching of the C=O group at 1715 cm-1 is
Chapter 2: Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles
80
masked by the changes in the band corresponding to the bending modes of water at ca.
1650 cm1.
Fig. 2.5. SPAIR spectra obtained in 0.1 M H2SO4 + 0.2 M CH3CH2OH for the (poly)Pt (top) and
(100)Pt (bottom) nanoparticles.
Results and discussion
81
Fig. 2.6. SPAIR spectra obtained in 0.1 M H2SO4 + 0.2 M CH3CH2OH for the (100)-(111)Pt (top) and
(111)Pt (bottom) nanoparticles.
In order to observe differences between the different nanoparticles, a quantitative
analysis should be made, using the integrated intensity of each band. However, the
absolute intensity for the bands depends on two experimental parameters that cannot be
easily controlled. The same electrode can yield different band intensities depending on the
thin layer gap between the electrode and the window and on the exact nanoparticle
concentration in the spot where the IR beam hits the sample. Although the absolute
intensity bands cannot be used, the relative band intensity can always be used, because all
Chapter 2: Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles
82
the bands are affected in the same way by the experimental conditions. In this case, the
integrated intensity band at 1400 cm-1 at 0.9 V, which corresponds to acetic acid, the main
product of the reaction, has been used to normalize the other adsorption bands. In addition,
for the CO bands, because of the presence of CO at the reference potential, spectra were
recalculated so that the reference spectrum for this signal is that taken at 0.90 V. At this
potential value, the CO band in Fig. 2.5 and Fig. 2.6 is always negative, indicating that
adsorbed CO is probably no longer on the electrode surface.
Fig. 2.7 shows the ratio of the normalized integrated bands of CO and CO2 with
respect to that of acetic acid. As can be seen these ratios are strongly dependent on the used
nanoparticles, revealing that the final product distribution is very sensitive to the
arrangement of the atoms at the nanoparticles surface. First, concerning the relative amount
of CO (Fig. 2.7A), two different trends can be observed. On the one hand, the
nanoparticles having a large ratio of 111 domains, that is, (111)Pt and (100)-(111)Pt
show a very low CO formation at low potentials. This fact means that the rate of cleavage
of the C-C bond is very low, which is a typical behavior of the single crystal electrodes
with 111 terraces. In fact, it has been reported that for those electrodes, the formation of
CO occurs on the defects or steps [20, 25, 55], so that this process would not occur on a
perfect (defect-free) Pt(111) electrode.
On the other hand, the most active basal plane for the formation of CO is the Pt(100)
electrode. Thus, the nanoparticles having a large fraction of 100 sites display the largest
activity for the cleavage of the C-C bond at low potentials. For the (poly)Pt nanoparticles,
although they do not have a large fraction of ordered domains, they possess a large fraction
of low coordinated atoms on the surface. This type of sites is also effective to cleave the C-
C bond, and a significant amount of adsorbed CO is obtained. For these two nanoparticle
samples, the amount of CO is almost constant between 0.1 and 0.5 V (the onset potential of
CO oxidation) which implies that the cleavage of the C-C bond has occurred at low
potentials and adsorbed CO blocks the surface almost completely.
Results and discussion
83
Fig. 2.7. Ratio between integrated intensity of the bands for (A) CO at 2030-2070 cm-1 and (B) CO2 at
2340 cm-1 at different potentials and the integrated intensity for acetate at 1400 cm-1 at 0.9 V.
A similar situation is observed for CO2 formation. CO2 is detected above 0.6-0.7 V,
which is the onset potential of CO oxidation. For the (100)Pt nanoparticles, the onset is the
highest of all the samples, probably as a consequence of the formation of a CO layer with a
higher coverage. From that point, the amount of CO2 increases with the potential, a clear
indication that the cleavage of the C-C bond is taking place at those potentials. Above 0.6
V, the cleavage of the ethanol C-C bond produces two adsorbed CO molecules that can be
readily oxidized. Thus, the actual CO coverage on the surface at those potentials depends
on the relative ratio of the rates for CO formation and CO oxidation. In this particular
situation, (poly)Pt nanoparticles are the most active for CO2 production. Although the
(100)Pt nanoparticles are clearly more active for the cleavage of the C-C bond, the large
CO coverage formed on the platinum nanoparticles surface makes its oxidation more
difficult. Thus, the nanoparticles with an intermediate activity for the C-C bond cleavage
0.0
0.2
0.4
0.6
0.8
1.0
1.2
B
Ratio
CO/
Aceta
te
(poly)Pt (100)Pt (100)-(111)Pt (111)Pt
A
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
Ratio
CO 2/A
ceta
te
E vs RHE/V
(poly)Pt (100)Pt (100)-(111)Pt (111)Pt
Chapter 2: Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles
84
are those having the highest activity for CO2 production. In this case, nanoparticles are
active for breaking the C-C bond, but the activity is not very high so that dense CO layers
are not formed and as a result the oxidation of CO to CO2 is easier. On the other hand,
nanoparticles with a large fraction of 111 sites produce a low amount of CO2.
Conclusions
85
2.4 Conclusions
Ethanol oxidation has been studied on polyoriented and (100), (111) and (100)-(111)
preferentially oriented Pt nanoparticles using electrochemical and IR experiments. The
results point out that the surface structure of nanoparticles plays an important role in the
reactivity, and that the activity of the nanoparticles can be predicted from the results
obtained for the single crystal electrodes, which can be taken as model surfaces. In
addition, the electrocatalytic properties are directly related to the surface structure/shape of
the nanoparticles. In all the platinum nanoparticles samples, the incomplete oxidation of
ethanol to acetaldehyde/acetic acid and the cleavage of the C-C bond to form CO and
finally its complete oxidation to CO2 are observed. However, the ratio of both paths is
different for the different catalysts. On the one hand, nanoparticles with a large fraction of
111 domains form acetic acid almost exclusively. On the other hand, (100)-rich Pt
nanoparticles are the best choice for the splitting of the C-C bond. Thus, polyoriented
platinum nanoparticles, which have an intermediate behavior between the (100)Pt and the
(111)Pt nanoparticles, show the highest activity for CO2 production.
Finally, it should be highlighted that, as previously stated in the Introduction section,
the ethanol electrooxidation activity can be modulated if a surface modifier such as Ru or
Sn is added onto the surface of the nanoparticles. So far, however, the used Pt
nanoparticles have not been preferentially oriented. In this sense, we have previously
shown that the use of adatom decorated shape-controlled Pt nanoparticles is a very relevant
approach to enhance the electrocatalytic properties of the bare samples [56-58]. We are
currently working on this approach towards ethanol electrooxidation electrocatalysis and
the results obtained will be reported in forthcoming contributions.
Chapter 2: Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles
86
2.5 References
[1] R. R. Adzic, ''Reaction kinetics and Mechanism on Metal Single Crystal Electrode surfaces'', in Modern aspects of electrochemistry, vol. 21, R. E. White, J. O. M. Bockris and B. E. Conway (Eds.) Plenum Press, New York, 1990, pp. 163-236.
[2] N. M. Markovic and P. N. Ross, ''Electrocatalysis at Well-Defined Surfaces: Kinetics of Oxygen Reduction and Hydrogen Oxidation/Evolution on Pt(hkl) Electrodes'', in Interfacial Electrochemistry: Theory, Experiments and Applications, A. Wieckowski (Ed.) Marcel Dekker, New York, 1998, pp. 821-842.
[3] N. M. Markovic and P. N. Ross, ''Surface science studies of model fuel cell electrocatalysts'' Surface Science Reports 2002, 45, 117-229.
[4] S. Sriramulu, T. D. Javi and E. M. Stuve, ''Kinetic Modeling of Electrocatalytic Reactions: Methanol Oxidation on Platinum Electrodes'', in Interfacial Electrochemistry: Theory, Experiments and Applications, A. Wieckowski (Ed.) Marcel Dekker, New York, 1998, pp. 793-804.
[5] E. Herrero, J. M. Feliu and A. Aldaz, ''Electrocatalysis'', in Encyclopedia of Electrochemistry - Interfacial Kinetics and Mass Transport, vol. 2, A. J. Bard and M. Stratmann (Eds.) Wiley, Weinheim, Germany, 2003, pp. 443-465.
[6] M. T. M. Koper, R. A. van Santen and M. Neurock, ''Theory and Modeling of Catalytic and Electrocatalytic Reactions'', in Catalysis and Electrocatalysis at Nanoparticle Surfaces, A. Wieckowski, E. R. Savinova and C. G. Vayenas (Eds.) Marcel Dekker, New York, 2003, pp. 1-34.
[7] F. J. Vidal-Iglesias, J. Solla-Gullón, P. Rodríguez, E. Herrero, V. Montiel, J. M. Feliu and A. Aldaz, ''Shape-dependent electrocatalysis: ammonia oxidation on platinum nanoparticles with preferential (100) surfaces'' Electrochemistry Communications 2004, 6, 1080-1084.
[8] J. Hernández, J. Solla-Gullón and E. Herrero, ''Gold nanoparticles synthesized in a water-in-oil microemulsion: electrochemical characterization and effect of the surface structure on the oxygen reduction reaction'' Journal of Electroanalytical Chemistry 2004, 574, 185-196.
[9] J. Hernández, J. Solla-Gullón, E. Herrero, A. Aldaz and J. M. Feliu, ''Characterization of the surface structure of gold nanoparticles and nanorods using structure sensitive reactions'' Journal of Physical Chemistry B 2005, 109, 12651-12654.
[10] J. Hernández, J. Solla-Gullón, E. Herrero, A. Aldaz and J. M. Feliu, ''Electrochemistry of shape-controlled catalysts: Oxygen reduction reaction on cubic gold nanoparticles'' Journal of Physical Chemistry C 2007, 111, 14078-14083.
[11] J. Solla-Gullón, F. J. Vidal-Iglesias, E. Herrero, J. M. Feliu and A. Aldaz, ''CO monolayer oxidation on semi-spherical and preferentially oriented (100) and (111) platinum nanoparticles'' Electrochemistry Communications 2006, 8, 189-194.
[12] J. Solla-Gullón, F. J. Vidal-Iglesias, A. López-Cudero, E. Garnier, J. M. Feliu and A. Aldaz, ''Shape-dependent electrocatalysis: methanol and formic acid electrooxidation on preferentially oriented Pt nanoparticles'' Physical Chemistry Chemical Physics 2008, 10, 3689-3698.
[13] V. Grozovski, J. Solla-Gullón, V. Climent, E. Herrero and J. M. Feliu, ''Formic Acid Oxidation on Shape-Controlled Pt Nanoparticles Studied by Pulsed Voltammetry'' Journal of Physical Chemistry C 2010, 114, 13802-13812.
[14] J. Solla-Gullón, F. J. Vidal-Iglesias and J. M. Feliu, ''Shape dependent electrocatalysis'' Annual Reports on the Progress of Chemistry, Section C: Physical Chemistry 2011, 107, 263-297.
[15] Q. S. Chen, F. J. Vidal-Iglesias, J. Solla-Gullón, S. G. Sun and J. M. Feliu, ''Role of surface defect sites: From Pt model surfaces to shape-controlled nanoparticles'' Chemical Science 2012, 3, 136-147.
[16] T. Iwasita and E. Pastor, ''A DEMS and FTIR spectroscopic investigation of adsorbed ethanol on polycrystalline platinum'' Electrochimica Acta 1994, 39, 531-537.
References
87
[17] J. W. Shin, W. J. Tornquist, C. Korzeniewski and C. S. Hoaglund, ''Elementary steps in the oxidation and dissociative chemisorption of ethanol on smooth and stepped surface planes of platinum electrodes'' Surface Science 1996, 364, 122-130.
[18] A. Rodes, E. Pastor and T. Iwasita, ''An FTIR Study on the Adsorption of Acetate at the Basal Planes of Platinum Single-Crystal Electrodes'' Journal of Electroanalytical Chemistry 1994, 376, 109-118.
[19] F. Colmati, G. Tremiliosi-Filho, E. R. Gonzalez, A. Berná, E. Herrero and J. M. Feliu, ''Surface structure effects on the electrochemical oxidation of ethanol on platinum single crystal electrodes'' Faraday Discussions 2008, 140, 379-397.
[20] F. Colmati, G. Tremiliosi-Filho, E. R. Gonzalez, A. Berná, E. Herrero and J. M. Feliu, ''The role of the steps in the cleavage of the C-C bond during ethanol oxidation on platinum electrodes'' Physical Chemistry Chemical Physics 2009, 11, 9114-9123.
[21] G. A. Camara and T. Iwasita, ''Parallel pathways of ethanol oxidation: The effect of ethanol concentration'' Journal of Electroanalytical Chemistry 2005, 578, 315-321.
[22] S. C. S. Lai, S. E. F. Kleyn, V. Rosca and M. T. M. Koper, ''Mechanism of the Dissociation and Electrooxidation of Ethanol and Acetaldehyde on Platinum As Studied by SERS'' Journal of Physical Chemistry C 2008, 112, 19080-19087.
[23] J. F. E. Gootzen, W. Visscher and J. A. R. van Veen, ''Characterization of ethanol and 1,2-ethanediol adsorbates on platinize d platinum with Fourier transform infrared spectroscopy and differential electrochemical mass spectrometry'' Langmuir 1996, 12, 5076-5082.
[24] G. A. Camara, R. B. de Lima and T. Iwasita, ''Catalysis of ethanol electro oxidation by PtRu: the influence of catalyst composition'' Electrochemistry Communications 2004, 6, 812-815.
[25] V. Del Colle, A. Berná, G. Tremiliosi-Filho, E. Herrero and J. M. Feliu, ''Ethanol electrooxidation onto stepped surfaces modified by Ru deposition: electrochemical and spectroscopic studies'' Physical Chemistry Chemical Physics 2008, 10, 3766-3773.
[26] C. Lamy, S. Rousseau, E. M. Belgsir, C. Coutanceau and J. M. Léger, ''Recent progress in the direct ethanol fuel cell: development of new platinum-tin electrocatalysts'' Electrochimica Acta 2004, 49, 3901-3908.
[27] Q. W. Zheng, C. H. Fan, C. H. Zhen, Z. Y. Zhou and S. G. Sun, ''Irreversible adsorption of Sn adatoms on basal planes of Pt single crystal and its impact on electrooxidation of ethanol'' Electrochimica Acta 2008, 53, 6081-6088.
[28] W. J. Zhou, S. Q. Song, W. Z. Li, Z. H. Zhou, G. Q. Sun, Q. Xin, S. Douvartzides and P. Tsiakaras, ''Direct ethanol fuel cells based on PtSn anodes: the effect of Sn content on the fuel cell performance'' Journal of Power Sources 2005, 140, 50-58.
[29] J. P. I. de Souza, S. L. Queiroz, K. Bergamaski, E. R. Gonzalez and F. C. Nart, ''Electro-oxidation of ethanol on Pt, Rh, and PtRh electrodes. A study using DEMS and in-situ FTIR techniques'' Journal of Physical Chemistry B 2002, 106, 9825-9830.
[30] A. Kowal, M. Li, M. Shao, K. Sasaki, M. B. Vukmirovic, J. Zhang, N. S. Marinkovic, P. Liu, A. I. Frenkel and R. R. Adzic, ''Ternary Pt/Rh/SnO2 electrocatalysts for oxidizing ethanol to CO2'' Nature Materials 2009, 8, 325-330.
[31] W. P. Zhou, M. Li, C. Koenigsmann, C. Ma, S. S. Wong and R. R. Adzic, ''Morphology-dependent activity of Pt nanocatalysts for ethanol oxidation in acidic media: Nanowires versus nanoparticles'' Electrochimica Acta 2011, 56, 9824-9830.
[32] J. Barroso, A. R. Pierna, T. C. Blanco, E. Morallón and F. Huerta, ''Homolytic cleavage C-C bond in the electrooxidation of ethanol and bioethanol'' Journal of Power Sources 2011, 196, 4193-4199.
[33] C. Z. Zhu, S. J. Guo and S. J. Dong, ''PdM (M = Pt, Au) Bimetallic Alloy Nanowires with Enhanced Electrocatalytic Activity for Electro-oxidation of Small Molecules'' Advanced Materials 2012, 24, 2326-2331.
Chapter 2: Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles
88
[34] J. M. Sieben and M. M. E. Duarte, ''Nanostructured Pt and Pt-Sn catalysts supported on oxidized carbon nanotubes for ethanol and ethylene glycol electro-oxidation'' International Journal of Hydrogen Energy 2011, 36, 3313-3321.
[35] J. Clavilier, D. Armand, S. G. Sun and M. Petit, ''Electrochemical adsorption behaviour of platinum stepped surfaces in sulphuric acid solutions'' Journal of Electroanalytical Chemistry 1986, 205, 267-277.
[36] J. Clavilier, K. El Achi, M. Petit, A. Rodes and M. A. Zamakhchari, ''Electrochemical Monitoring of the Thermal Reordering of Platinum Single-Crystal Surfaces after Metallographic Polishing from the Early Stage to the Equilibrium Surfaces'' Journal of Electroanalytical Chemistry 1990, 295, 333-356.
[37] J. Solla-Gullón, P. Rodríguez, E. Herrero, A. Aldaz and J. M. Feliu, ''Surface characterization of platinum electrodes'' Physical Chemistry Chemical Physics 2008, 10, 1359-1373.
[38] A. López-Cudero, F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero, A. Aldaz and J. M. Feliu, ''Formic acid electrooxidation on Bi-modified polyoriented and preferential (111) Pt nanoparticles'' Physical Chemistry Chemical Physics 2009, 11, 416-424.
[39] F. J. Vidal-Iglesias, R. M. Arán-Ais, J. Solla-Gullón, E. Herrero and J. M. Feliu, ''Electrochemical Characterization of Shape-Controlled Pt Nanoparticles in Different Supporting Electrolytes'' ACS Catalysis 2012, 2, 901-910.
[40] J. Solla-Gullón, V. Montiel, A. Aldaz and J. Clavilier, ''Electrochemical characterization of platinum nanoparticles prepared by microemulsion: How to clean them without loss of crystalline surface structure'' Journal of Electroanalytical Chemistry 2000, 491, 69-77.
[41] J. Solla-Gullón, V. Montiel, A. Aldaz and J. Clavilier, ''Synthesis and electrochemical decontamination of platinum-palladium nanoparticles prepared by water-in-oil microemulsion'' Journal of the Electrochemical Society 2003, 150, E104-E109.
[42] T. S. Ahmadi, Z. L. Wang, T. C. Green, A. Henglein and M. A. El-Sayed, ''Shape-controlled synthesis of colloidal platinum nanoparticles'' Science 1996, 272, 1924-1926.
[43] Q. S. Chen, J. Solla-Gullón, S. G. Sun and J. M. Feliu, ''The potential of zero total charge of Pt nanoparticles and polycrystalline electrodes with different surface structure: The role of anion adsorption in fundamental electrocatalysis'' Electrochimica Acta 2010, 55, 7982-7994.
[44] T. Iwasita, F. C. Nart and W. Vielstich, ''An FTIR study of the catalytic activity of a 85:15 Pt:Ru alloy for methanol oxidation'' Berichte der Bunsen-Gesellschaft fuer Physikalische Chemie 1990, 94, 1030-1034.
[45] A. Rodes, J. M. Pérez and A. Aldaz, ''Vibrational spectroscopy'', in Handbook of Fuel Cells - Fundamentals, Technology and Applications, vol. 2, W. Vielstich, A. Lamm and H. A. Gasteiger (Eds.) Wiley, Chichester, 2003, pp. 191-219.
[46] J. Souza-Garcia, E. Herrero and J. M. Feliu, ''Breaking the C-C Bond in the Ethanol Oxidation Reaction on Platinum Electrodes: Effect of Steps and Ruthenium Adatoms'' ChemPhysChem 2010, 11, 1391-1394.
[47] M. C. Morin, C. Lamy, J. M. Léger, J. L. Vázquez and A. Aldaz, ''Structural effects in electrocatalysis: Oxidation of ethanol on platinum single crystal electrodes. Effect of pH'' Journal of Electroanalytical Chemistry 1990, 283, 287-302.
[48] M. J. Prieto and G. Tremiliosi-Filho, ''The influence of acetic acid on the ethanol electrooxidation on a platinum electrode'' Electrochemistry Communications 2011, 13, 527-529.
[49] M. E. Gamboa-Aldeco, E. Herrero, P. S. Zelenay and A. Wieckowski, ''Adsorption of Bisulfate Anion on a Pt(100) Electrode - a Comparison with Pt(111) and Pt(Poly)'' Journal of Electroanalytical Chemistry 1993, 348, 451-457.
[50] M. D. Maciá, J. M. Campiña, E. Herrero and J. M. Feliu, ''On the kinetics of oxygen reduction on platinum stepped surfaces in acidic media'' Journal of Electroanalytical Chemistry 2004, 564, 141-150.
References
89
[51] S. Chumillas, C. Busó-Rogero, J. Solla-Gullón, F. J. Vidal-Iglesias, E. Herrero and J. M. Feliu, ''Size and diffusion effects on the oxidation of formic acid and ethanol on platinum nanoparticles'' Electrochemistry Communications 2011, 13, 1194-1197.
[52] J. Mostany, E. Herrero, J. M. Feliu and J. Lipkowski, ''Thermodynamic studies of anion adsorption at stepped platinum(hkl) electrode surfaces in sulfuric acid solutions'' Journal of Physical Chemistry B 2002, 106, 12787-12796.
[53] E. Herrero, J. Mostany, J. M. Feliu and J. Lipkowski, ''Thermodynamic studies of anion adsorption at the Pt(111) electrode surface in sulfuric acid solutions'' Journal of Electroanalytical Chemistry 2002, 534, 79-89.
[54] X. H. Xia, H. D. Liess and T. Iwasita, ''Early stages in the oxidation of ethanol at low index single crystal platinum electrodes'' Journal of Electroanalytical Chemistry 1997, 437, 233-240.
[55] V. Del Colle, J. Souza-Garcia, G. Tremiliosi-Filho, E. Herrero and J. M. Feliu, ''Electrochemical and spectroscopic studies of ethanol oxidation on Pt stepped surfaces modified by tin adatoms'' Physical Chemistry Chemical Physics 2011, 13, 12163-12172.
[56] F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero, A. Aldaz and J. M. Feliu, ''Pd Adatom Decorated (100) Preferentially Oriented Pt Nanoparticles for Formic Acid Electrooxidation'' Angewandte Chemie-International Edition 2010, 49, 6998-7001.
[57] F. J. Vidal-Iglesias, A. López-Cudero, J. Solla-Gullón and J. M. Feliu, ''Towards More Active and Stable Electrocatalysts for Formic Acid Electrooxidation: Antimony-Decorated Octahedral Platinum Nanoparticles'' Angewandte Chemie-International Edition 2013, 52, 964-967.
[58] Q. S. Chen, Z. Y. Zhou, F. J. Vidal-Iglesias, J. Solla-Gullón, J. M. Feliu and S. G. Sun, ''Significantly Enhancing Catalytic Activity of Tetrahexahedral Pt Nanocrystals by Bi Adatom Decoration'' Journal of the American Chemical Society 2011, 133, 12930-12933.
Capítulo 3: Oxidación de etanol en nanopartículas de platino con forma
controlada a diferentes pHs: estudio combinado de
espectroscopía IR in situ y espectrometría de masas en línea
93
Capítulo 3: Oxidación de etanol en nanopartículas de
platino con forma controlada a diferentes pHs: estudio
combinado de espectroscopía IR in situ y espectrometría de
masas en línea
RESUMEN
El cambio del pH en el electrolito soporte modifica la reactividad del etanol sobre las
superficies de platino, alterando la proporción de ácido acético/acetato formado respecto al
CO/CO2 producido tras su oxidación. En este capítulo, se aborda el efecto del pH sobre dos
superficies diferentes, concretamente las dos muestras principales que muestran más
diferencias entre sí de los casos estudiados en el capítulo 2, las nanopartículas (100)Pt y las
nanopartículas (111)Pt. La investigación se realizará a valores de pH ácidos menores a 4,
ya que a valores superiores, el CO2 comienza a reaccionar para dar carbonato, lo que
impide su correcta cuantificación por DEMS. Además, en todo momento se utiliza una
concentración 0.5 M SO42- de electrolito soporte para minimizar la adsorción del anión
acetato. El estudio se lleva a cabo con la combinación de las técnicas ATR y DEMS,
permitiendo a la vez un seguimiento espectroscópico de las especies formadas, junto a
información cuantitativa de las mismas especies con la espectrometría de masas en el caso
de que los productos sean gases volátiles. En este capítulo, la concentración de etanol es en
todo momento 0.05 M, menor de lo habitual, para evitar problemas de saturación en la
membrana del DEMS.
Después de la caracterización electroquímica, se registran los perfiles voltamétricos
para la oxidación de etanol en las dos muestras de nanopartículas empleadas. En ambas
muestras se observan corrientes despreciables a potenciales bajos e histéresis entre el ciclo
positivo y negativo del barrido de potenciales, características presentes cuando hay
envenenamiento por formación de CO. Al aumentar el pH la histéresis disminuye,
probablemente debido a la menor formación de CO, a pesar de que las corrientes obtenidas
Capítulo 3: Oxidación de etanol en nanopartículas de platino con forma controlada a diferentes pHs: un estudio combinado de espectroscopía IR in situ y espectrometría de masas en línea
94
difieren dependiendo de la muestra empleada: en la muestra (100)Pt la corriente de pico se
mantiene, indicando que a pesar de la menor cantidad de veneno producida, la actividad
total en la oxidación de etanol se conserva. En cambio, en la muestra (111)Pt, las corrientes
y la forma de la voltametría cíclica varían totalmente, revelando un posible cambio en
cuanto al mecanismo de reacción en los sitios 111, lo cual se tratará de explicar con
experimentos DEMS.
A continuación se inicia el estudio espectroscópico con los experimentos de ATR
obtenidos a 0.4 V para las dos muestras estudiadas y a diferentes pHs, usando como
referencia el espectro a 0.9 V. En todos los casos, la banda observada entre 2030 y 2070
cm-1 se corresponde con la adsorción del CO lineal sobre las nanopartículas de platino,
observándose una pequeña disminución de la banda al aumentar el pH, confirmando la
menor formación de CO. A diferencia de los espectros del capítulo 2, la banda asociada a
la adsorción de acetato no se observa en este caso, ya que los experimentos son realizados
en configuración de célula de flujo, que elimina el ácido acético formado en las
proximidades del electrodo de trabajo, impidiendo su adsorción sobre la superficie de
platino.
En cuanto a los experimentos DEMS, se comparan en primer lugar las corrientes de
espectrometría de masas junto a las corrientes faradaicas correspondientes a una velocidad
de barrido de 5 mVs-1. Las corrientes de masas registradas en esta primera tanda de
experimentos son la m/z=29 y la m/z=44. La corriente de m/z=44 presenta contribuciones
del acetaldehído (CH3CHO+) y del CO2, mientras que la corriente m/z=29 solamente se
debe a la contribución del acetaldehído (CHO+). A partir de estas corrientes, y siguiendo
las Ec. (3.2), y (3.3), se obtiene la corriente faradaica producto de la formación de CO2. La
forma de esta corriente es similar a la de la oxidación de una monocapa de CO, esto es, a
potenciales de 0.7 V la corriente empieza a crecer debido a la oxidación del CO hasta CO2.
Además, en el barrido negativo de potenciales, la ausencia de corriente indica que la rotura
del enlace C-C sólo sucede a bajos potenciales, demostrando que toda la corriente de
oxidación de etanol en el barrido negativo se debe a la formación de acetaldehído/ácido
acético. La Fig. 3.7 muestra las eficiencias de formación de CO2 para un valor de pH de
0.3 para las dos muestras estudiadas, de acuerdo con la Ec. (3.4). Comparando los
resultados, queda claro que las nanopartículas (100)Pt tienen una mayor eficiencia para la
Resumen
95
formación de CO2 que las nanopartículas (111)Pt (10% vs 5%). Fijándose en el potencial al
cual se obtiene la máxima eficiencia, en ambos casos el valor está sobre 0.65 V, más
pequeño que el potencial de pico que muestran las curvas de corriente faradaica de CO2.
Esto es debido a la competición entre el proceso de oxidación incompleta de etanol hasta
acetaldehído/acético y el de la oxidación del CO adsorbido.
A partir de los resultados previos y como era de esperar, se corrobora que la rotura
del enlace C-C es la clave para la oxidación completa del etanol. Con el objetivo de
conocer los fragmentos adsorbidos en el electrodo tras la oxidación de etanol, se realizan
unos experimentos conocidos como ‘stripping’ de etanol para las diferentes muestras de
nanopartículas de platino. El experimento consiste en hacer pasar por la célula de flujo a
0.4 V la disolución de etanol y luego registrar la corriente cuando se realiza un barrido de
potenciales a 5 mVs-1 en la disolución sin etanol. Los resultados se muestran en la Fig. 3.8
y la Fig. 3.9. Las voltametrías cíclicas de los apartados a) de ambas figuras muestran la
corriente faradaica, cuyo pico a altos potenciales se corresponde con la oxidación del CO
(formado a 0.4 V) a CO2. Resultados de la bibliografía muestran que la rotura de la
molécula produce siempre 2 fragmentos. El fragmento CH2OH evoluciona de forma casi
instantánea para dar CO adsorbido, mientras que el CHx no reacciona de forma rápida con
la superficie. Los apartados b) y c) muestran las corrientes de espectrometría de masa para
m/z=15, con la reducción de los fragmentos CHx a CH4 a bajos potenciales, y para m/z=44,
con la oxidación del CO a CO2.
Los resultados son bastante diferentes, dependiendo de la muestra. Las
nanopartículas (100)Pt muestran una cantidad creciente del fragmento CHx formado a
bajos potenciales conforme avanza el pH, como demuestra el aumento de la cantidad de
CH4 registrada, mientras que la formación de CO se mantiene constante, como indican las
corrientes de espectrometría de masa m/z=44 del apartado c) en la Fig. 3.8. En cambio,
para las nanopartículas (111)Pt de la Fig. 3.9, las cantidades de CH4 y CO2 disminuyen con
el pH. Este comportamiento se puede explicar por la distinta evolución de las reacciones de
rotura del enlace C-C y de reducción de los fragmentos de CHx a CH4. Para las
nanopartículas (100)Pt, la velocidad de rotura del enlace C-C es elevada, y aunque
disminuye con el pH, es capaz de saturar la superficie con CO durante el tiempo de
contacto a 0.4 V con la disolución de etanol. De esta forma, la cantidad de CO2 medida tras
Capítulo 3: Oxidación de etanol en nanopartículas de platino con forma controlada a diferentes pHs: un estudio combinado de espectroscopía IR in situ y espectrometría de masas en línea
96
la oxidación se mantiene constante. Sin embargo, el proceso de reducción del fragmento de
CHx se ve favorecido al aumentar el pH, lo que lleva a mayores cantidades de CH4. Por
otra parte, para las nanopartículas de (111)Pt, la rotura del enlace C-C es mucho menos
eficiente y en el tiempo de la experiencia nunca se llega a saturar la superficie con CO. De
esta forma, al aumentar el pH disminuye la velocidad de rotura del enlace C-C, lo que lleva
a menores cantidades de CO2 y CH4 detectadas.
97
Chapter 3
This chapter has been adapted and formatted from Journal of Electroanalytical Chemistry 2016, 763, 116-
124.
Corresponding author: [email protected]
Chapter 3: Ethanol oxidation on shape-controlled platinum nanoparticles at different pHs: a combined in situ IR spectroscopy and online mass spectrometry study
98
3.1 Introduction
During the last years, the search for new energy sources has been intensified due to
the depletion of fossil fuels. In this sense, fuel cell technology has gained momentum for
obtaining electric energy from the oxidation of a chemical fuel [1]. In the quest for possible
new fuels, several options have been considered and particularly the oxidation of some
small organic molecules such as formic acid, methanol or ethanol has been extensively
evaluated. The oxidation of these molecules normally requires the use of platinum as
catalyst [2-4]. Among these fuels, ethanol presents some relevant advantages to other fuels
as i) it can be obtained directly from biomass and ii) it does not present problems for its
storage. Unfortunately, and despite its high density energy for the complete oxidation to
CO2, with 12 electrons exchanged, problems dealing with a classical CO poisoning as well
as to an incomplete oxidation to undesired products such as acetic acid, limit its
potentialities for practical purposes.
Ethanol oxidation is also known to be a surface structure sensitive reaction, that is,
the resulting catalytic activity depends on the particular/specific arrangement of the surface
atoms. This surface structure sensitivity has been clearly evidenced by the use of Pt single
crystal electrodes [5-7]. However, single crystal electrodes are ideal model surfaces which
cannot be used in real electrocatalytic systems. For this reason, these results have to be
extended to nanoparticles, which can be effectively applied to such systems. As previously
demonstrated, the effect of the particular arrangement of the atoms at the surface on the
resulting ethanol oxidation activity is valid also for nanoparticles [8], thus highlighting the
importance of gaining control of the surface structure of the nanoparticles to increase their
electrocatalytic activity. Similar results on the effect of the surface structure of the
nanoparticles for other important reactions such as oxygen reduction or other small organic
molecule oxidations have been already reported [9-15]. In this sense, it is also worth noting
that these shape/surface structure controlled Pt nanoparticles are usually about 8-10 nm in
size which, from a practical point of view, may be insufficient to fulfill the requirement of
a high surface-to-volume ratio for practical applications.
From a mechanistic point of view, it is known that, in acidic solutions the reaction
occurs via a complex reaction network. Scheme (3.1) illustrates a simplified mechanism
Introduction
99
where some additional steps such as desorption and re-adsorption of acetaldehyde have not
been included for the sake of clarity.
(3.1)
Reaction steps (1) and (2) give rise to the incomplete oxidation of ethanol, forming
acetaldehyde and acetic acid as final products. To obtain this latter product, which is very
difficult to oxidize, only four electrons are exchanged, thus wasting 2/3 of the formal
energy density for ethanol. On Pt(111) electrodes and at room temperature, the reaction
only takes places almost exclusively through this undesirable route [5]. On the other hand,
the splitting of the C-C bond occurs in steps (3) and (4), which produce different carbon
fragments that are subsequently transformed to COads (step (5)) [5]. Finally, in step (6),
COads is oxidized to CO2, thus completing the 12 electron exchange route. This reaction
route presents two difficult steps, i) the splitting of the C-C bond and ii) the oxidation of
adsorbed CO. Pt(110) and especially Pt(100) electrodes favor the C-C bond scission, but
suffer from surface poisoning. The enhancement of the C-C bond breaking rate needs to be
accompanied by a higher rate for COads oxidation to avoid poisoning. In fact, the stronger
the metal-adsorbate bond, the more C-C bond breaking is favored, while COads oxidation is
disfavored. This is likely to result in a Sabatier type behavior with an optimum bond
strength. In order to overcome this COads poisoning problem, the incorporation of different
foreign atoms has been used to facilitate COads oxidation to CO2 [16-18]. In addition, the
breakage of C-C bond is known to be improved on Pt surfaces containing 100 and 110
steps on 111 terraces [6, 19]. Consequently, a combination of these two approaches, that
is, using stepped Pt electrodes and foreign adatoms, gave rise to significant improvements
in the oxidation reaction [20-22].
On the other hand, the research of alkaline fuel cells (AFC) has currently grown due
to the higher activity obtained at these pHs and also due to the their less corrosive
properties, which favor the use of cheaper catalysts. In fact, the problems resulting from
the carbonation of the system due to CO2 retention as well as from the limited number of
membranes capable of operating over long periods of time in alkaline media seem to be
Chapter 3: Ethanol oxidation on shape-controlled platinum nanoparticles at different pHs: a combined in situ IR spectroscopy and online mass spectrometry study
100
solved with the development of new anion-exchange membranes [23, 24]. According to
fundamental studies performed in alkaline solutions [7, 25, 26], acetate is presented as the
main product for ethanol oxidation regardless the surface structure of the Pt electrode, with
negligible amounts of COads being formed. Consequently, a better understanding of the
changes in the oxidation mechanism as a function of the pH and in particular, how the ratio
between the products (incomplete oxidation to acetate or complete oxidation towards CO2)
is modified for increasing pHs, would be of utmost interest.
To access this information, we have performed a combined in situ infrared (IR)
spectroscopy and online mass spectrometry study on different shape controlled Pt
nanoparticles of the ethanol oxidation reaction (EOR) at different pHs. These experiments
will be performed under well-defined mass transport conditions and with control of the
surface structure, in contrast to infrared reflection-absorption spectroscopy (IRRAS)
measurements, where by-product accumulation, e.g. adsorbed acetate, is common. Such
experimental conditions are more convenient for mechanistic investigations. On the other
hand, it is also worth noting that only pHs lower than 4 have been explored in order to
avoid problems due to carbonate formation. This combined approach allows us to not only
perform a quantitative analysis of the volatile products formed during the reaction and to
calculate the efficiencies for the complete oxidation to CO2, but also to follow the nature
and potential window in which the adsorbed intermediate species are formed during the
reaction.
Experimental
101
3.2 Experimental
Two different kinds of Pt nanoparticles were used in this work. They were both
synthesized using a colloidal method [27, 28], and displayed preferential 100 or 111
surface orientations. These nanoparticles were denoted as (100)Pt nanoparticles and
(111)Pt nanoparticles, depending on their dominant surface structure. Experimental details
about the synthesis, also including Transmission Electron Microscopy (TEM)
characterization to determine their particle size and characterize their preferential shape,
were previously described [29]. Very briefly, the predominant shape was cubic for (100)Pt
nanoparticles and octahedral for (111)Pt ones. The particle size of both nanoparticle
batches was estimated to be about 8-10 nm. The electrodes were prepared by depositing a
droplet (4 μL) of the aqueous solution containing the nanoparticles on a hemispherical gold
substrate, after which the electrode was protected under an Ar stream until complete
solvent evaporation. Before the measurements, Pt nanoparticles were carefully cleaned by
CO adsorption and subsequent stripping at potentials below 0.95 V to preserve the surface
structure of the samples. The electrochemically active area of Pt nanoparticles was
measured using the charge involved in the so-called hydrogen/anion adsorption/desorption
region (between 0.05 V and 0.6 V) from the cyclic voltammograms recorded in 0.5 M
H2SO4, assuming that the charge density for this region is 230 μC cm-2 in sulfuric acid
solutions [30].
IR spectroelectrochemical probing of adsorbates and online detection of volatile
reaction products were performed simultaneously using a dual thin-layer
spectroelectrochemical flow-cell in which ATR-FTIR and DEMS measurements can be
carried put. A more detailed description of this flow-cell configuration was previously
given in [31]. In brief, the central cell is a double thin-layer flow cell, equipped with two Pt
counter electrodes (a Pt gauge and a Pt wire) at the inlet and the outlet of flow cell. For
electrolyte changing, two electrolyte reservoirs are available, one with the supporting
electrolyte alone and one with ethanol + supporting electrolyte. The working electrode is
prepared by depositing the nanoparticles on a Au film covering a Si wafer, which in turn is
coupled with the flat side of a hemispherical Si prism. The Au film was prepared by
electroless deposition following the procedure reported previously [32-34]. It has to be thin
Chapter 3: Ethanol oxidation on shape-controlled platinum nanoparticles at different pHs: a combined in situ IR spectroscopy and online mass spectrometry study
102
enough to allow the IR radiation to pass to the nanoparticles, but thick enough to be
sufficiently conductive for obtaining a good electrochemical response.
In the first thin-layer compartment, the flat side of the prism was pressed via a
circular tightening gasket and a Cu foil current collector against the Kel-F body of the cell,
forming a thin electrolyte layer with a volume of ca. 10 μL. The electrolyte flows to the
second thin-layer compartment through six capillaries. The second thin-layer compartment
is connected via a porous Teflon membrane to a mass spectrometer, such that gaseous
species can pass through and be detected on-line.
The in situ ATR-FTIRS experiments were performed in a BioRad FTS-6000
spectrometer equipped with a homemade reflection accessory (incident angle of 70º) and
mercury cadmium telluride (MCT) detector. The resolution and the acquisition time per
spectra were 4 cm-1 and 10 s, respectively. The spectra are presented in absorbance values,
as the ratio –log R/R0, where R and R0 are the reflectance values corresponding with the
single beam spectra measured at the sample or reference potential, respectively. Negative
bands in the spectra correspond with species formed at the sampling potential, whereas
positive bands indicate a consumption of the species with respect to reference potential.
The DEMS setup is explained in detail in ref. [35]. Briefly, it is based on a
differentially pumped two-chamber system coupled with a Balzers QMS 12 quadrople
mass spectrometer, a Pine Instruments potentiostat and a computerized data acquisition
system. In all the mass spectrometry experiments, large Pt loadings were used to favor the
performance of DEMS experiments.
The calibration constant for CO2 was determined by passing a CO saturated solution
at 0.1 V until the Pt surface is completely blocked. Then, the electrolyte is changed to CO-
free supporting electrolyte for 15 min, to assure the complete removal of dissolved CO in
the thin-layer cell. After that, a COads stripping experiment was carried out. The calibration
constant K* was calculated by comparison of the Faradaic oxidation current and the CO2
mass signal, using the following equation [36]:
𝐾∗ = 𝑧𝑄𝑀𝑆𝑄𝐹
(3.2)
Experimental
103
where z is the number of electrons exchanged in the CO oxidation reaction to CO2, QMS is
the integrated charge of the mass current for the CO2 spectrometric signal (m/z=44) and QF
is the integrated Faradaic current charge in the COad stripping peak.
To eliminate contributions from acetaldehyde species to the mass signal m/z=44 for
calculating the CO2 current efficiency in the ethanol oxidation reaction, the following
equation was used:
𝐼𝑀𝑆(𝐶𝑂2) = 𝐼(𝑚/𝑧 = 44) − 𝑛 × 𝐼(𝑚/𝑧 = 29) (3.3)
where n is a parameter determined from the ratio between the stable I44 and I29 currents in
the oxidation transients at 0.9 V at each pH, and assuming that the efficiency for
acetaldehyde production at this potential is 100%, as has been observed previously [36].
The values obtained for n are always between 0.60 and 0.65. To convert this CO2 mass
current to the Faradaic current, the calibration constant K* was used:
𝐼𝐹(𝐶𝑂2) = 𝑧𝐼𝑀𝑆(𝐶𝑂2)
𝐾∗ (3.4)
For this expression, z is equal to 6, the number of electrons exchanged per C atom for
completing CO2 oxidation. Finally, the CO2 current efficiency is the ratio between CO2 and
total Faradaic currents:
𝐴𝐶𝑂2 =𝐼𝐹(𝐶𝑂2)
𝐼𝐹 (3.5)
All experiments were carried out at room temperature. Millipore Milli Q water (18.2
MΩ cm), H2SO4 (Suprapur, Merck), Na2SO4 (HiPerSolv, Prolabo) and ethanol absolute
(Merck p.a.) were used to prepare the solutions. Solutions of different pH were obtained by
adding some droplets of H2SO4 to 0.5 M SO42- solutions until the desired pH value was
reached. The sulfate concentration was kept at approximately 0.5 M for all experiments.
Solutions were deaerated with N2/Ar, and CO (Messer-Griesheim, N 4.7) was used to
saturate the supporting electrolyte solution used for cleaning the nanoparticles and for
calibrating the DEMS signals. A Saturated Calomel Electrode (SCE) served as a reference
Chapter 3: Ethanol oxidation on shape-controlled platinum nanoparticles at different pHs: a combined in situ IR spectroscopy and online mass spectrometry study
104
during the simultaneous ATR-FTIRS/DEMS experiments, but all the potentials presented
in this paper are referred to that of the reversible hydrogen electrode (RHE).
Results and discussion
105
3.3 Results and discussion
3.3.1 Electrochemical characterization
Fig. 3.1 shows the characteristic cyclic voltammetric profiles in 0.5 M H2SO4 for the
Pt nanoparticles used in this work. Both cyclic voltammograms (CVs) show symmetric
voltammetric peaks, which is an indication of the surface cleanness. The resulting
voltammetric profiles can be considered as a fingerprint of each Pt nanoparticle sample and
allow a detailed evaluation of the specific surface structure [29].
Fig. 3.1. Voltammetric profiles corresponding to a) (100)Pt and b) (111)Pt nanoparticles in 0.5 M
H2SO4. Scan rate: 0.05 V s-1.
As previously shown, the main features are those related to the presence of large
100 ordered domains (signal at about 0.37 V) due to the hydrogen adsorption/desorption
process and those associated with the sulfate adsorption on 111 ordered domains (signal
about 0.5 V) [29]. As expected, cubic Pt nanoparticles displayed the characteristic feature
-0.10
-0.05
0.00
0.05
0.10
0.150.0 0.2 0.4 0.6 0.8
0.0 0.2 0.4 0.6 0.8-0.15
-0.10
-0.05
0.00
0.05
0.10 b)
E/V vs. RHE
j/mA
cm-2
a) 100 sites
j/mA
cm-2
E/V vs. RHE
111 sites
Chapter 3: Ethanol oxidation on shape-controlled platinum nanoparticles at different pHs: a combined in situ IR spectroscopy and online mass spectrometry study
106
of the wide 100 domains while for octahedral ones the CV was dominated by the
characteristic features coming from the 111 ordered domains. A more detailed analysis
about the correlations between shape, surface structure and resulting voltammetric profiles
has been done previously in our group [12, 29, 30].
3.3.2 Ethanol oxidation at low pHs
The voltammetric responses for ethanol oxidation (1st scan) obtained with the
different Pt nanoparticles in 0.05 M EtOH + 0.5 M SO42- at two different pH values are
displayed in Fig. 3.2. As previously mentioned, the upper potential limit is limited to 0.95
V in order to avoid significant changes of the Pt surfaces due to oxide formation/reduction
processes. Also, and in comparison with previous works [7, 8], the ethanol concentration is
lowered to prevent problems with membrane saturation in the DEMS experiments.
Fig. 3.2. Voltammetric profiles for a) (100)Pt and b) (111)Pt nanoparticles in 0.05 M CH3CH2OH +
0.5 M SO42- at different pHs. Scan rate: 0.02 V s-1.
0.00.10.20.30.40.50.60.7
0.0 0.2 0.4 0.6 0.8 1.0
0.0 0.2 0.4 0.6 0.8 1.0-0.10.00.10.20.30.40.5 b)
pH=0.3 pH=3.5
j/mA
cm-2
a)
pH=0.3 pH=3.5
E/V vs. RHE
j/mA
cm-2
E/V vs. RHE
Results and discussion
107
As mentioned before, experiments were carried out at pH values below 4 to avoid
carbonate formation from the reaction of CO2 with water, which can mask the CO2
efficiency. On the other hand, the surface area of the nanoparticles was kept relatively low
(0.03-0.05 cm2 of active area) to ensure that the entire deposit is contributing to the
oxidation reaction. In this sense, it is worth noting that the use of high metal loadings and
consequently high surface areas creates nanostructured electrodes in which only the outer
part of the deposit is effectively working, due to a poor diffusion of ethanol to the inner
parts, giving rise to lower than expected current densities [37].
In the positive-going sweep and at potentials below ca. 0.4 V, the voltammetric
profiles present low currents due to the formation of COads, which blocks the active
surface. As has been shown, this process takes place even at potentials as low as 0.1 V [20,
21], and COads is accumulated on the surface since it is not effectively oxidized at room
temperature at E<0.6 V. As the potential is increased, COads is oxidized and the current
increases until an oxidation peak at around 0.8 V is observed. From this point, ethanol
oxidation is hindered by adsorbed species (anions present in solution or OH-) and/or by the
incipient oxide formation.
In the negative-going sweep and after the reactivation of the surface, currents are
higher than those measured in the positive-going scan, since the surface is now free from
COads and for E>0.6 V, the possible COads formed in the process is immediately oxidized.
This fact leads to a hysteresis between both scan directions, which is proportional to the
amount of COads formed at low potentials. The decrease at E<0.6 V is a consequence of the
COads re-poisoning of the surface and the diminution of oxidation rates as the electrode
potential diminishes [38, 39]. However, this process depends on the surface structure and
on the pH of the electrolyte.
At pH=0.3, (100)Pt nanoparticles (Fig. 3.2a) present a more prominent peak at 0.8 V,
which is a characteristic of 100 surfaces. As it has been previously shown in single
crystal electrode studies, Pt(100) is more active for the formation of CO than the Pt(111)
electrode, leading to a complete blockage of the surface at low potentials [5]. The
subsequent oxidation of CO with the concomitant reactivation of the surface gives rise to
the peak at 0.8 V on the Pt(100) electrode [5, 8]. This preference for CO formation at low
Chapter 3: Ethanol oxidation on shape-controlled platinum nanoparticles at different pHs: a combined in situ IR spectroscopy and online mass spectrometry study
108
potentials is also the cause of a more pronounced hysteresis between positive and negative-
going sweeps for the (100)Pt nanoparticles than for the (111)Pt ones. However, by
increasing the pH, this hysteresis decreases for both nanoparticle samples, probably due to
a lower COads formation rate, as will be shown later.
In terms of maximum current densities, (100)Pt nanoparticles (Fig. 3.2a) display a
similar peak current density for the two pH values, which means that, despite different CO
formation and probably different CO2 current efficiencies, the overall activity for the
reaction, under non-stationary conditions, is maintained. On the other hand, (111)Pt
nanoparticles (Fig. 3.2b) show a lower hysteresis and higher peak current as the pH
increases, suggesting that cleavage of the C-C bond is disfavored and acetaldehyde/acetic
acid products are preferred instead of CO2 formation. This fact seems to be in good
agreement with what was observed for surfaces with large 111 ordered domains in
strongly alkaline solutions [7, 40], where only the incomplete oxidation is achieved and no
adsorbed CO is detected in the whole potential range. This discussion will be continued in
the next sections with data obtained from DEMS experiments.
To evaluate the adsorbed species present on the Pt surface during ethanol oxidation
at these pHs, FTIR experiments were carried out. Fig. 3.3 displays ATR measurements at
0.4 V vs RHE, using spectra taken at 0.9 V, where CO is completely oxidized to CO2, as
reference spectra. All spectra were recorded under almost stationary conditions. At 0.4 V,
the fragments formed from ethanol oxidation poison the active surface.
In the IR experiments, the main band observed corresponds to linearly adsorbed CO
in the spectral range between 2030 and 2070 cm-1. In the two samples studied, (100)Pt and
(111)Pt nanoparticles (Fig. 3.3a and 3.3b respectively), the CO bands diminish with
increasing pH, as it was predicted from the hysteresis in the voltammetric experiments.
Comparing the two experiments, it seems that the CO bands are higher for 100 domains
than for 111 sites in agreement with our previous findings [8]. Unfortunately, the direct
comparison done in this paper cannot be done due to the different experimental conditions
for each electrode and the no appearance of the adsorbed acetate band, which is used for
normalize the amount of CO formed.
Results and discussion
109
Fig. 3.3. ATR spectra obtained at E=0.4 V vs RHE for (a) (100)Pt and (b) (111)Pt nanoparticles in 0.05
M CH3CH2OH + 0.5 M SO42- at different pHs (reference spectra at 0.9 V).
This absence of the adsorbed acetate band is due to the fact that these experiments
are performed under flow cell conditions, where the acetic acid formed in the reaction is
readily removed from the vicinity of the electrode, thus preventing its adsorption as weakly
bound acetate. Thus, in this way, its accumulation on the surface is minimized, thus
allowing a better approach to the understanding of the reaction mechanism.
3.3.3 DEMS experiments
For obtaining new quantitative data about the formation of acetate, CO2, CHx or
other intermediates or products during ethanol oxidation, DEMS experiments were carried
out. Fig. 3.4 and Fig. 3.5 display cyclic voltammetric experiments and the corresponding
mass spectrometric currents (m/z=44 and m/z=29) obtained at different pH values using
(100)Pt and (111)Pt nanoparticles, respectively.
2400 2200 2000 1800 2400 2200 2000 1800υ/cm-1
pH=0,3 pH=2,5 pH=3,7
1E-4 a.u.
COL b)
υ/cm-1
pH=0,3 pH=2,4 pH=3,4
1E-4 a.u.
COLa)
E=0.4 V vs RHE
Chapter 3: Ethanol oxidation on shape-controlled platinum nanoparticles at different pHs: a combined in situ IR spectroscopy and online mass spectrometry study
110
Fig. 3.4. Cyclic voltammetry (top) and mass spectrometric cyclic voltammograms for m/z=44 and
m/z=29 (bottom) for the 2nd cycle during ethanol electroxidation in 0.05 M CH3CH2OH + 0.5 M SO42- on
(100)Pt nanoparticles. Scan rate: 0.005 V s-1.
The scan rate used during the experiments was 5 mV s-1 and the flow rate was around
10 μL s-1. In the figures, the 2nd cycle in DEMS experiments is presented, because this
profile is a very good approximation to the steady-state behavior. As described in the
experimental section, the m/z=44 current includes contributions from acetaldehyde
(CH3CHO+) and CO2, whereas the m/z=29 signal only includes contributions from the
acetaldehyde (CHO+) fragment.
In the case of (100)Pt nanoparticles (Fig. 3.4), the shape of the mass spectrometric
voltammogram for I29 is similar to that observed for the Faradaic current, which suggests
that ethanol oxidation proceeds mainly via acetaldehyde formation. However, the I44 mass
spectrometric voltammogram shows some slight differences in the region at 0.7-0.8 V,
probably due to the formation of CO2 from the oxidation of COads generated at lower
potentials. On the other hand, for (111)Pt nanoparticles (Fig. 3.5), the shape of the I29 and
I44 mass spectrometric voltammograms are almost identical, confirming that COads
formation/COads oxidation is less than in the previous case. For both nanoparticle samples,
0.0
0.2
0.4
0.6
0.8
1.0
1.2
0.0 0.2 0.4 0.6 0.8 1.0
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.0 0.2 0.4 0.6 0.8 1.0
0.0
0.2
0.4
0.6
0.8
1.0
0.0
0.1
0.2
0.3
0.4
0.5
0.0 0.2 0.4 0.6 0.8 1.0
0.0
0.2
0.4
0.6
0.8
1.0
1.2
pH=3.7pH=0.3
I F / m
ApH=2.5
I MS /
nA
E vs RHE/V
I (m/z=44) I (m/z=29)
I F / m
A
I MS /
nA
E vs RHE/V
I (m/z=44) I (m/z=29)
I F / m
A
I MS /
nA
E vs RHE/V
I (m/z=44) I (m/z=29)
Results and discussion
111
I29 and I44 come only from acetaldehyde formation at higher potentials than 0.9 V, where
COads formed at lower potentials has been completely oxidized to CO2 [36].
Fig. 3.5. Cyclic voltammetry (top) and mass spectrometric cyclic voltammograms for m/z=44 and
m/z=29 (bottom) for the 2nd cycle during ethanol electroxidation in 0.05 M CH3CH2OH + 0.5 M SO42- on
(111)Pt nanoparticles. Scan rate: 0.005 V s-1.
Considering the current peaks in the mass spectrometric signals for the negative-
going potential scan, the ratio between I44 and I29 is around 60%, independent of the pH or
the Pt sample. This is the same relative intensity as obtained in the steady-state oxidation
process at 0.9 V. This ratio will be used later for calculating the CO2 efficiency.
Comparing the peak potentials measured for the three different pH values studied, the peak
potential is shifted positively with increasing pH for (100)Pt nanoparticles, while for the
(111)Pt nanoparticles no significant change is observed. Since the peak for the (100)Pt
nanoparticles is mainly related to the oxidation of the adsorbed CO, this would mean that
COads oxidation is shifted toward more positive values as the pH increases due to the
different COads coverages observed in this sample. This effect is not observed for (111)Pt
nanoparticles, presumably due to the lower amount of COads formed at low potentials [5,
19].
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.0 0.2 0.4 0.6 0.8 1.00.0
0.2
0.4
0.6
0.8
0.00
0.04
0.08
0.12
0.16
0.0 0.2 0.4 0.6 0.8 1.0
0.00
0.05
0.10
0.15
0.20
0.25
0.0
0.1
0.2
0.3
0.4
0.0 0.2 0.4 0.6 0.8 1.0
0.0
0.1
0.2
0.3
0.4
0.5
I F / m
A
I MS /
nA
E vs RHE/V
I (m/z=44) I (m/z=29)
I F / m
A
I MS /
nA
E vs RHE/V
I (m/z=44) I (m/z=29)
I F / m
A
pH=3.4pH=2.4
I MS /
nA
E vs RHE/V
I (m/z=44) I (m/z=29)
pH=0.3
Chapter 3: Ethanol oxidation on shape-controlled platinum nanoparticles at different pHs: a combined in situ IR spectroscopy and online mass spectrometry study
112
Fig. 3.6. CO2 formation currents using data from Fig. 3.4 and Fig. 3.5 for 0.05 M CH3CH2OH + 0.5 M
SO42- (see text for more details).
Fig. 3.6 displays CO2 Faradaic currents for the two samples studied during this work,
calculated using Eqs. (3.3) and (3.4). The data used to calculate these currents were
obtained from Fig. 3.4 and Fig. 3.5. These experiments were done to clarify the preference
of 100 sites for complete oxidation as compared to 111 domains.
The shape of the CO2 Faradaic current vs. E curve is similar to the voltammogram
measured during a COads stripping experiment, showing a peak at around 0.7 V vs RHE,
which corresponds to the oxidation of adsorbed CO to CO2. The shape of this CO2 current
trace agrees well with previous findings [41]. Also, the peak potential for the CO2 Faradaic
current shifts toward higher values with increasing pH, especially for the (100)Pt
0.00
0.01
0.02
0.03
0.04
0.05
0.06
0.00
0.01
0.02
0.03
0.04
0.05
0.0 0.2 0.4 0.6 0.8 1.0
0.00
0.01
0.02
0.03
0.000
0.005
0.010
0.015
-0.002
0.000
0.002
0.004
0.006
0.0 0.2 0.4 0.6 0.8 1.0
0.000
0.005
0.010
pH=0.3
I fara
daic C
O 2 / m
A
pH=2.5
I fara
daic C
O 2 / mA
pH=3.7
I fara
daic C
O 2 / mA
E vs RHE/V
pH=0.3
I fara
daic C
O 2 / mA
pH=2.4
I fara
daic C
O 2 / mA
pH=3.4
Pt (111) nanoparticles
I fara
daic C
O 2 / mA
E vs RHE/V
Pt (100) nanoparticles
Results and discussion
113
nanoparticles, corroborating that the peak potential shift in the voltammogram is mainly
related to the oxidation of adsorbed CO. The absence of currents in the negative scan
direction clearly indicates that the cleavage of the C-C bond occurs only at low potentials,
below 0.5 V. At those potentials, the cleavage produces adsorbed CO, which is only
oxidized in the subsequent positive-going scan at higher potentials. If the cleavage of the
C-C bond had taken place at high potentials, some Faradaic current for CO2 formation
would have been detected in the negative scan direction.
In order to better compare the CO2 efficiency of the two samples, the current
efficiencies for CO2 at pH=0.3 calculated using Eq. (3.5) are displayed in Fig. 3.7 for the
positive scan direction.
Fig. 3.7. CO2 current efficiency vs potential for (100)Pt nanoparticles and (111)Pt nanoparticles in the
ethanol oxidation reaction (0.05 M) in 0.5 M H2SO4 (pH=0.3).
Maximum efficiencies are obtained at ca. 0.65 V for both samples. This potential is
lower than the peak potential for the Faradaic CO2 current, due to the competition between
the oxidation of ethanol to acetaldehyde and acetic acid and that of adsorbed CO. As the
COads stripping process takes place, ethanol oxidation current becomes higher due to the
0.5 0.6 0.7 0.8 0.9 1.00
2
4
6
8
10
12
Effic
iency
/ %
E vs RHE/V
(100) Pt nanoparticles (111) Pt nanoparticles
Chapter 3: Ethanol oxidation on shape-controlled platinum nanoparticles at different pHs: a combined in situ IR spectroscopy and online mass spectrometry study
114
potential increase and also due to the rise in the number of free sites on the surface, where
the partial oxidation of ethanol can occur. It should be highlighted that both curves have a
very similar shape, indicating that the same type of sites are active for the C-C bond
cleavage on both samples. The only difference between them is their relative number on
the samples.
3.3.4 Ethanol stripping experiments
From the FTIR-DEMS results it is clear that the cleavage of the C-C bond is the key
process to achieve the complete oxidation of ethanol. This process takes place at potentials
below 0.4 V [42]. Results with single crystal electrodes have shown that once the C-C
bond is broken, the carbon containing the alcohol group immediately evolves to give
adsorbed CO, whereas the CHx fragment only yields adsorbed CO at E>0.4-0.5 V [43]. To
obtain additional information on this process, ethanol stripping experiments were done. In
this experiment, an ethanol solution is flown through the cell at 0.4 V for two minutes, to
allow the cleavage of ethanol molecules and adsorption of fragments. After that, the
solution is changed to a solution containing only the supporting electrolyte at the same pH
and then the electrode is cycled between 0.04 and 0.95 V vs RHE at v=5 mVs-1, registering
simultaneously the Faradic and mass spectrometric ion currents [39, 44].
Fig. 3.8 displays ethanol stripping experiments for the (100)Pt nanoparticles,
studying ion currents m/z=15 and m/z=44. I15 provides information about the CHx
fragment in its reduction to CH4 at low potentials [36, 45] whereas I44 in this particular
case only gives information about CO2 formed, since ethanol has been removed from the
solution. Some authors have also evaluated the mass current m/z=61, which corresponds to
a fragment of ethyl acetate (CH3COOH2+), to follow the acetic acid formation, whose
volatility is low and cannot be detected in DEMS experiments [46, 47]. However, as
shown in these papers, the intensity of this mass current signal is very low and,
consequently, it was not measured in the present contribution.
Results and discussion
115
Fig. 3.8. Ethanol stripping experiments after adsorption for 2 minutes in 0.05 M ethanol + 0.5 M SO42-
at 0.4 V vs RHE on (100)Pt nanoparticles: Voltammetric response at 0.005 V s-1 (a) and mass spectrometric
current densities of m/z=15 (b) and m/z=44 (c).
Fig. 3.8a shows the voltammetric profile after ethanol adsorption for (100)Pt
nanoparticles. As expected, in the 1st cycle, active sites of platinum nanoparticles are
blocked due to COads formation. At higher potentials, COads is oxidized to CO2 and the
voltammogram recovers the characteristic features of the (100)Pt nanoparticles in the so-
called hydrogen region. Fig. 3.8b shows mass currents at m/z=15 simultaneously recorded
with the voltammogram. At low potentials (around 0.1 V), a small peak is detected due to
CH4 formation from the reduction of the CHx fragment. This signal increases with the pH.
At higher potentials, adsorbed CO is oxidized to CO2, as it can be seen in Fig. 3.8c. For
this type of nanoparticles, I44 peak does not significantly change with the pH.
Chapter 3: Ethanol oxidation on shape-controlled platinum nanoparticles at different pHs: a combined in situ IR spectroscopy and online mass spectrometry study
116
Fig. 3.9. Ethanol stripping experiments after adsorption for 2 minutes in 0.05 M ethanol + 0.5 M SO42-
at 0.4 V vs RHE on (111)Pt nanoparticles: Voltammetric response at 0.005 V s-1 (a) and mass spectrometric
current densities of m/z=15 (b) and m/z=44 (c).
Fig. 3.9 shows the same experiments as done in Fig. 3.8, but using (111)Pt
nanoparticles. From the evolution of the I15 and I44 currents with the pH it can be seen that
both signals decrease significantly with pH. In order to quantitatively analyze the results of
both samples, the normalized charges under mass signals m/z=15 and m/z=44 have been
calculated (Fig. 3.10).
Results and discussion
117
Fig. 3.10. a) CHx and b) CO2 charge vs pH. Data obtained from Fig. 3.8 and 3.9.
As stated before, at 0.4 V, ethanol molecules can dissociate, giving rise to two single
carbon containing fragments, the one containing the oxygen group, which immediately
reacts to adsorbed CO, and the CHx fragment, which is more difficult to oxidize to form
adsorbed CO. The CHx fragment can also interact with the surface and be reduced at low
potentials. Depending on the cleavage rate and the rate for the oxidation of the CHx
fragment to COads. and how these rates evolve with the pH, several situations can be found.
For the (100)Pt nanoparticles, the amount of COads is independent of the pH, which
indicates that the COads coverage has reached a value where further C-C bond cleavage is
fully inhibited. Probably only isolated sites remain free and, on those sites, this process
cannot take place. This means that the C-C bond cleavage is fast enough to produce a
saturated adlayer of CO during the time (2 min.) at 0.4 V. Since the oxidation of the CHx
fragment is very slow at 0.4 V, the increase of the signal for CH4 production as the pH
increases indicates that the oxidation of this fragment to yield adsorbed CO is even slower.
406080
100120140160180
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
600800
100012001400160018002000
(100) Pt nanoparticles (111) Pt nanoparticles
b)
Q j(m/z)
=15 /
pC
cm-2
a)
Q j(m/z)
=44 /
pC
cm-2
pH
Chapter 3: Ethanol oxidation on shape-controlled platinum nanoparticles at different pHs: a combined in situ IR spectroscopy and online mass spectrometry study
118
At lower pHs, the saturated CO adlayer formed contains a higher fraction of COads
molecules coming from the CHx fragment and for this reason the signal is small. As the pH
increases, the oxidation rate of this fragment to COads diminishes at a higher rate than that
of the C-C bond cleavage, resulting in a higher number of unreacted CHx fragments on the
electrode surface, thus producing a higher current for CH4 production.
On the other hand, for the (111)Pt nanoparticles, the rate for the C-C cleavage is
slower, because of the lower fraction of 100 sites on the sample. Thus, lower CO
coverages are obtained as revealed in Fig. 3.10. These coverages are below the saturation
value. On the other hand, the charge for CH4 production at pH=0.3 is similar to that
measured for the (100)Pt nanoparticles, which indicates that also the oxidation rate of CHx
to CO is low for these nanoparticles. As the pH increases, C-C bond cleavage rate
diminishes, resulting in lower COads coverages and lower CH4 formation. The diminution
in the CH4 signal is proportionally smaller than that of the CO2 due to a two effects. The C-
C bond cleavage rate is slower but also the transformation of the CHx fragment to CO,
resulting in a compensating effect in which the diminution of unreacted CHx fragments is
smaller. The lower reactivity of surfaces for the cleavage of the C-C bond as the pH
increases is in agreement with the results obtained in alkaline medium. In the latter
environment, only acetate bands are detected in FTIR experiments for ethanol oxidation
[7]. Bands related to CHx,ads have only been seen in wide 111 ordered domains by SERS
in these media [25], whereas these bands were not detected in the case of Pt polyoriented
surfaces [43], in agreement with our results.
Conclusions
119
3.4 Conclusions
Ethanol oxidation experiments with Pt nanoparticles were performed using
voltammetric, ATR and DEMS experiments, studying the acidic pH range below 4 to
avoid carbonate formation and using always 0.5 M SO42- to discard anion effects. As a
summary of the data obtained, the next scheme shows the preferred path for each site
taking into account the pH effect in acidic solutions:
(3.6)
The results presented clearly show structure effects related to the 100 and 111
domains, in agreement with studies done with single crystal electrodes. In spite of the fact
that the incomplete ethanol oxidation was established as the preferred route for both
samples, a higher activity for the formation of C1-fragments (COads, CHx,ads) as
intermediates was observed for 100 domains. The maximum CO2 efficiency calculated
from DEMS data corroborated this behavior, as it is higher for (100)Pt nanoparticles
(around 10%) than for (111)Pt nanoparticles (around 5%). When the pH is increased,
CHx,ads was also detected, in addition to COads. CHx,ads formation is favored at lower
potentials on preferentially oriented (100)Pt nanoparticles and decreasing CO formation.
For (111)Pt nanoparticles, COads formation is hindered and also the splitting of the C-C
bond, promoting acetaldehyde/acetic acid formation up to quasi-negligible CO2 formation
at higher pHs.
Chapter 3: Ethanol oxidation on shape-controlled platinum nanoparticles at different pHs: a combined in situ IR spectroscopy and online mass spectrometry study
120
3.5 References
[1] M. T. M. Koper, ''Fuel Cell Catalysis: A Surface Science Approach'', Electrocatalysis and Electrochemistry A. Wieckowski (Ed.), John Wiley & Sons, Hoboken, New Jersey, 2009.
[2] C. Rice, R. I. Ha, R. I. Masel, P. Waszczuk, A. Wieckowski and T. Barnard, ''Direct formic acid fuel cells'' Journal of Power Sources 2002, 111, 83-89.
[3] T. Iwasita, ''Electrocatalysis of methanol oxidation'' Electrochimica Acta 2002, 47, 3663-3674.
[4] E. Antolini, ''Catalysts for direct ethanol fuel cells'' Journal of Power Sources 2007, 170, 1-12.
[5] F. Colmati, G. Tremiliosi-Filho, E. R. Gonzalez, A. Berná, E. Herrero and J. M. Feliu, ''Surface structure effects on the electrochemical oxidation of ethanol on platinum single crystal electrodes'' Faraday Discussions 2008, 140, 379-397.
[6] F. Colmati, G. Tremiliosi-Filho, E. R. Gonzalez, A. Berná, E. Herrero and J. M. Feliu, ''The role of the steps in the cleavage of the C-C bond during ethanol oxidation on platinum electrodes'' Physical Chemistry Chemical Physics 2009, 11, 9114-9123.
[7] C. Busó-Rogero, E. Herrero and J. M. Feliu, ''Ethanol Oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium'' ChemPhysChem 2014, 15, 2019-2028.
[8] C. Busó-Rogero, V. Grozovski, F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero and J. M. Feliu, ''Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles'' Journal of Materials Chemistry A 2013, 1, 7068-7076.
[9] J. Hernández, J. Solla-Gullón and E. Herrero, ''Gold nanoparticles synthesized in a water-in-oil microemulsion: electrochemical characterization and effect of the surface structure on the oxygen reduction reaction'' Journal of Electroanalytical Chemistry 2004, 574, 185-196.
[10] J. Solla-Gullón, F. J. Vidal-Iglesias, A. López-Cudero, E. Garnier, J. M. Feliu and A. Aldaz, ''Shape-dependent electrocatalysis: methanol and formic acid electrooxidation on preferentially oriented Pt nanoparticles'' Physical Chemistry Chemical Physics 2008, 10, 3689-3698.
[11] F. J. Vidal-Iglesias, J. Solla-Gullón, V. Montiel, J. M. Feliu and A. Aldaz, ''Ammonia selective oxidation on Pt(100) sites in an alkaline medium'' Journal of Physical Chemistry B 2005, 109, 12914-12919.
[12] V. Grozovski, J. Solla-Gullón, V. Climent, E. Herrero and J. M. Feliu, ''Formic Acid Oxidation on Shape-Controlled Pt Nanoparticles Studied by Pulsed Voltammetry'' Journal of Physical Chemistry C 2010, 114, 13802-13812.
[13] F. J. Vidal-Iglesias, R. M. Arán-Ais, J. Solla-Gullón, E. Garnier, E. Herrero, A. Aldaz and J. M. Feliu, ''Shape-dependent electrocatalysis: formic acid electrooxidation on cubic Pd nanoparticles'' Physical Chemistry Chemical Physics 2012, 14, 10258-10265.
[14] F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero, A. Aldaz and J. M. Feliu, ''Pd Adatom Decorated (100) Preferentially Oriented Pt Nanoparticles for Formic Acid Electrooxidation'' Angewandte Chemie-International Edition 2010, 49, 6998-7001.
[15] C. Busó-Rogero, J. V. Perales-Rondón, M. J. S. Farias, F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero and J. M. Feliu, ''Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity'' Physical Chemistry Chemical Physics 2014, 16, 13616-13624.
[16] C. Lamy, S. Rousseau, E. M. Belgsir, C. Coutanceau and J. M. Léger, ''Recent progress in the direct ethanol fuel cell: development of new platinum-tin electrocatalysts'' Electrochimica Acta 2004, 49, 3901-3908.
[17] A. O. Neto, R. R. Dias, M. M. Tusi, M. Linardi and E. V. Spinacé, ''Electro-oxidation of methanol and ethanol using PtRu/C, PtSn/C and PtSnRu/C electrocatalysts prepared by an alcohol-reduction process'' Journal of Power Sources 2007, 166, 87-91.
References
121
[18] J. P. I. de Souza, S. L. Queiroz, K. Bergamaski, E. R. Gonzalez and F. C. Nart, ''Electro-oxidation of ethanol on Pt, Rh, and PtRh electrodes. A study using DEMS and in-situ FTIR techniques'' Journal of Physical Chemistry B 2002, 106, 9825-9830.
[19] S. C. S. Lai and M. T. M. Koper, ''Electro-oxidation of ethanol and acetaldehyde on platinum single-crystal electrodes'' Faraday Discussions 2008, 140, 399-416.
[20] V. Del Colle, J. Souza-Garcia, G. Tremiliosi-Filho, E. Herrero and J. M. Feliu, ''Electrochemical and spectroscopic studies of ethanol oxidation on Pt stepped surfaces modified by tin adatoms'' Physical Chemistry Chemical Physics 2011, 13, 12163-12172.
[21] J. Souza-Garcia, E. Herrero and J. M. Feliu, ''Breaking the C-C Bond in the Ethanol Oxidation Reaction on Platinum Electrodes: Effect of Steps and Ruthenium Adatoms'' ChemPhysChem 2010, 11, 1391-1394.
[22] V. Del Colle, A. Berná, G. Tremiliosi-Filho, E. Herrero and J. M. Feliu, ''Ethanol electrooxidation onto stepped surfaces modified by Ru deposition: electrochemical and spectroscopic studies'' Physical Chemistry Chemical Physics 2008, 10, 3766-3773.
[23] J. R. Varcoe, R. C. T. Slade, E. L. H. Yee, S. D. Poynton, D. J. Driscoll and D. C. Apperley, ''Poly(ethylene-co-tetrafluoroethylene)-derived radiation-grafted anion-exchange membrane with properties specifically tailored for application in metal-cation-free alkaline polymer electrolyte fuel cells'' Chemistry of Materials 2007, 19, 2686-2693.
[24] C. Coutanceau, L. Demarconnay, C. Lamy and J. M. Léger, ''Development of electrocatalysts for solid alkaline fuel cell (SAFC)'' Journal of Power Sources 2006, 156, 14-19.
[25] S. C. S. Lai and M. T. M. Koper, ''Ethanol electro-oxidation on platinum in alkaline media'' Physical Chemistry Chemical Physics 2009, 11, 10446-10456.
[26] P. A. Christensen, S. W. M. Jones and A. Hamnett, ''In Situ FTIR Studies of Ethanol Oxidation at Polycrystalline Pt in Alkaline Solution'' Journal of Physical Chemistry C 2012, 116, 24681-24689.
[27] T. S. Ahmadi, Z. L. Wang, T. C. Green, A. Henglein and M. A. El-Sayed, ''Shape-controlled synthesis of colloidal platinum nanoparticles'' Science 1996, 272, 1924-1926.
[28] T. S. Ahmadi, Z. L. Wang, A. Henglein and M. A. El-Sayed, ''"Cubic" colloidal platinum nanoparticles'' Chemistry of Materials 1996, 8, 1161-1163.
[29] J. Solla-Gullón, P. Rodríguez, E. Herrero, A. Aldaz and J. M. Feliu, ''Surface characterization of platinum electrodes'' Physical Chemistry Chemical Physics 2008, 10, 1359-1373.
[30] Q. S. Chen, J. Solla-Gullón, S. G. Sun and J. M. Feliu, ''The potential of zero total charge of Pt nanoparticles and polycrystalline electrodes with different surface structure: The role of anion adsorption in fundamental electrocatalysis'' Electrochimica Acta 2010, 55, 7982-7994.
[31] M. Heinen, Y. X. Chen, Z. Jusys and R. J. Behm, ''In situ ATR-FTIRS coupled with on-line DEMS under controlled mass transport conditions - A novel tool for electrocatalytic reaction studies'' Electrochimica Acta 2007, 52, 5634-5643.
[32] S. Brimaud, Z. Jusys and R. J. Behm, ''Shape-selected nanocrystals for in situ spectro-electrochemistry studies on structurally well defined surfaces under controlled electrolyte transport: A combined in situ ATR-FTIR/online DEMS investigation of CO electrooxidation on Pt'' Beilstein Journal of Nanotechnology 2014, 5, 735-746.
[33] H. Miyake, S. Ye and M. Osawa, ''Electroless deposition of gold thin films on silicon for surface-enhanced infrared spectroelectrochemistry'' Electrochemistry Communications 2002, 4, 973-977.
[34] S. Brimaud, Z. Jusys and R. J. Behm, ''Controlled Surface Structure for In Situ ATR-FTIRS Studies Using Preferentially Shaped Pt Nanocrystals'' Electrocatalysis 2011, 2, 69-74.
[35] Z. Jusys and R. J. Behm, ''Methanol oxidation on a carbon-supported Pt fuel cell catalyst - A kinetic and mechanistic study by differential electrochemical mass spectrometry'' Journal of Physical Chemistry B 2001, 105, 10874-10883.
[36] A. A. Abd-El-Latif, E. Mostafa, S. Huxter, G. Attard and H. Baltruschat, ''Electrooxidation of ethanol at polycrystalline and platinum stepped single crystals A study by differential electrochemical mass spectrometry'' Electrochimica Acta 2010, 55, 7951-7960.
Chapter 3: Ethanol oxidation on shape-controlled platinum nanoparticles at different pHs: a combined in situ IR spectroscopy and online mass spectrometry study
122
[37] S. Chumillas, C. Busó-Rogero, J. Solla-Gullón, F. J. Vidal-Iglesias, E. Herrero and J. M. Feliu, ''Size and diffusion effects on the oxidation of formic acid and ethanol on platinum nanoparticles'' Electrochemistry Communications 2011, 13, 1194-1197.
[38] H. Wang, Z. Jusys and R. J. Behm, ''Ethanol electrooxidation on a carbon-supported Pt catalyst: Reaction kinetics and product yields'' Journal of Physical Chemistry B 2004, 108, 19413-19424.
[39] E. Mostafa, A. A. Abd-El-Latif, R. Ilsley, G. Attard and H. Baltruschat, ''Quantitative DEMS study of ethanol oxidation: effect of surface structure and Sn surface modification'' Physical Chemistry Chemical Physics 2012, 14, 16115-16129.
[40] C. Busó-Rogero, J. Solla-Gullón, F. J. Vidal-Iglesias, E. Herrero and J. M. Feliu, ''Oxidation of ethanol on platinum nanoparticles: surface structure and aggregation effects in alkaline medium'' Journal of Solid State Electrochemistry 2016, 20, 1095-1106.
[41] J. F. Gomes, D. Profeti and L. J. Deiner, ''Influence of the Particle Size Distribution on the Activity and Selectivity of Carbon-Supported Platinum Nanoparticle Catalysts for Ethanol Electrooxidation'' ChemElectroChem 2014, 1, 655-662.
[42] C. Lamy and C. Coutanceau, ''Electrocatalysis of Alcohol Oxidation Reactions at Platinum Group Metals'', in Catalysts for Alcohol-Fuelled Direct Oxidation Fuel Cells, vol. 6, Z.-X. Liang and T. S. Zhao (Eds.) RSC Energy and Enviroment Series 2012.
[43] S. C. S. Lai, S. E. F. Kleijn, F. T. Z. Öztürk, V. C. van Rees Vellinga, J. Koning, P. Rodriguez and M. T. M. Koper, ''Effects of electrolyte pH and composition on the ethanol electro-oxidation reaction'' Catalysis Today 2010, 154, 92-104.
[44] M. Heinen, Z. Jusys and R. J. Behm, ''Ethanol, Acetaldehyde and Acetic Acid Adsorption/Electrooxidation on a Pt Thin Film Electrode under Continuous Electrolyte Flow: An in Situ ATR-FTIRS Flow Cell Study'' Journal of Physical Chemistry C 2010, 114, 9850-9864.
[45] T. Iwasita and E. Pastor, ''A DEMS and FTIR spectroscopic investigation of adsorbed ethanol on polycrystalline platinum'' Electrochimica Acta 1994, 39, 531-537.
[46] T. Herranz, M. Ibañez, J. L. G. de la Fuente, F. J. Pérez-Alonso, M. A. Pena, A. Cabot and S. Rojas, ''In Situ Study of Ethanol Electrooxidation on Monodispersed Pt3Sn Nanoparticles'' ChemElectroChem 2014, 1, 885-895.
[47] S. C. S. Lai and M. T. M. Koper, ''The Influence of Surface Structure on Selectivity in the Ethanol Electro-oxidation Reaction on Platinum'' Journal of Physical Chemistry Letters 2010, 1, 1122-1125.
Capítulo 4: Oxidación de etanol en electrodos monocristalinos de Pt:
efecto de la estructura superficial en medio alcalino
125
Capítulo 4: Oxidación de etanol en electrodos
monocristalinos de Pt: efecto de la estructura superficial en
medio alcalino
RESUMEN
La investigación sobre la oxidación de pequeñas moléculas orgánicas a pHs básicos
tiene un gran interés en la actualidad debido al desarrollo de las membranas aniónicas.
Sobre el platino, la oxidación de etanol en estas condiciones tiene mayor actividad que en
medio ácido. Sin embargo, no existen demasiados estudios acerca del efecto de la
estructura superficial en medio alcalino, el principal objetivo de este capítulo. Para su
estudio, se usan electrodos monocristalinos de platino con estructura superficial
perfectamente conocida, empleando técnicas de voltametría cíclica y espectroscópicas.
En primer lugar, se muestra la caracterización electroquímica para los planos de base
del platino en medio 0.1 M NaOH, las cuales muestran algunas diferencias con respecto a
la caracterización habitual en medio ácido, sobre todo en los potenciales en los que aparece
la adsorción del OH, que en medio alcalino se solapa con la adsorción de hidrógeno en los
electrodos de Pt(100) y Pt(110).
La reacción de oxidación de etanol en electrodos de platino presenta una gran
actividad que, en algunas ocasiones, como en el estudio de la oxidación de etanol en
Pt(111), requiere una corrección de caída óhmica para la correcta realización de la
voltametría, como se indica en la Fig. 4.2. A continuación se muestran las voltametrías
cíclicas con la correspondiente desactivación para cada plano basal del Pt conforme pasan
los ciclos de oxidación-reducción. La dependencia del orden de actividad total con la
reactividad en los planes base del platino es Pt(111) > Pt(110) > Pt(100), la misma
tendencia que sigue el umbral de potencial necesario para iniciar la oxidación de etanol. La
histéresis entre el barrido positivo y negativo de potenciales es menor en el caso del
Capítulo 4: Oxidación de etanol en electrodos monocristalinos de Pt: efecto de la estructura superficial en medio alcalino
126
electrodo de Pt(111) y un poco mayor para el electrodo de Pt(100), aunque ésta no es
asignada a la presencia de CO adsorbido sobre el electrodo, debido a que la histéresis es
mucho menor que en los casos descritos en los capítulos anteriores. En cuanto a la
desactivación, cuanta más corriente de oxidación se observa, mayor es la desactivación,
como se observa en el electrodo de Pt(111), donde en el ciclo 25 la corriente es un 5% de
la inicial. Las cronoamperometrías a 0.6 V muestran la variación de la actividad con el
tiempo. Las corrientes a tiempos largos concuerdan con las voltametrías cíclicas anteriores,
siendo el Pt(110) el electrodo más activo y menos inhibido, y, por tanto, el que menos
potencial requiere para el inicio de oxidación de etanol.
Por otra parte, se estudia el efecto de introducir escalones de simetría 100 y 110
sobre terrazas 111 en la oxidación de etanol en medio alcalino. Al contrario que en
medio ácido, las voltametrías cíclicas indican una única mejora en el potencial de inicio de
la oxidación, decreciendo cada vez más la actividad total y aumentando la histéresis entre
el barrido positivo y el barrido negativo de potenciales, observándose más corriente para
las superficies con escalones 100 que las que presentan escalones 111. Al realizar
cronoamperometrías a 0.6 V, similares a las realizadas con los planos basales, se corrobora
la mayor reactividad inducida por la presencia de sitios 100 vista en la voltametría
cíclica, al contrario que en medio ácido, donde los escalones 110 son mucho más
activos.
Previamente a los experimentos espectroelectroquímicos con electrodos de platino,
se registraron los espectros de transmisión de los posibles productos en la oxidación de
etanol, para conocer sus bandas características. Concretamente, se asigna que las bandas
observadas a 1550 y 1415 cm-1 pertenecen al acetato, mientras que una banda a 1390 cm-1
es debida al carbonato, como se muestra en la Fig. 4.7, que contiene los espectros de
transmisión y su comparación con espectros de IRRAS realizados con el Pt(111). Dichos
espectros, realizados para los tres planos base del platino, muestran bandas de acetato
como producto mayoritario, independientemente del electrodo utilizado. Sin embargo, no
es descartable la formación de carbonato, cuya banda se puede solapar con la señal de
acetato, debido a que aparecen a frecuencias similares. Para intentar aclarar la proporción
entre el acetato y el carbonato formado, se ajustaron los espectros experimentales a 0.8 V
con los espectros de transmisión del carbonato y el acetato, buscando averiguar la
Resumen
127
contribución de cada especie al espectro en cada electrodo. En todos los casos la cantidad
de carbonato estimada resulta ser muy baja.
Retornando a las voltametrías de los planos base del platino observados en la Fig. 4.3
y comparándolas con las obtenidas en medio ácido, la principal diferencia es la mayor
actividad obtenida para el electrodo de Pt(111). La oxidación de etanol en este electrodo
únicamente tiene lugar a través de la ruta de oxidación incompleta hasta ácido acético
(acetato a pHs más elevados), por lo que la razón de estas altas corrientes es la de la no
adsorción de acetato, debido a que el potencial al cual se trabaja (en torno a 0.7 V frente a
RHE) es más negativo en la escala absoluta. En cuanto al potencial de inicio de la
oxidación de etanol, éste se desplaza hacia valores más positivos (sobre 0.6 V en escala
RHE), sugiriendo que es necesaria la adsorción de OH para iniciar la oxidación en medio
alcalino, al contrario que en medio ácido donde la especie dadora de oxígeno puede variar
debido al potencial absoluto más positivo. En los electrodos de Pt(100) y Pt(110), la
oxidación de etanol en 0.1 M NaOH también es desencadenada por la adsorción del OH,
que hace que el potencial al cual se inicia la oxidación de etanol sea menor.
En cuanto a la razón por la cual se produce la histéresis entre el barrido positivo y
negativo de la voltametría cíclica, sobre todo en el caso del Pt(100) y el Pt(110), no se debe
a la adsorción de CO, como en medio ácido. Es difícil asegurar cual es el intermedio que se
adsorbe e inhibe la reacción de oxidación de etanol. En la bibliografía se propone la
especie CHx como causante de la inhibición, aunque este hecho no puede asegurarse a
partir de los resultados espectroscópicos de la literatura. Otra posibilidad es la del
incremento en la irreversibilidad en la adsorción de OH al realizar la oxidación de etanol.
La fuerte desactivación de la superficie de platino es muy elevada y probablemente
es también causada por la misma especie inhibidora. La Fig. 4.9 muestra el efecto en la
voltametría registrada en 0.1 M NaOH, de las especies inhibidoras sobre un electrodo de
Pt(111) tras realizar 5 ciclos de oxidación-reducción de etanol. Como se ve, la carga de
adsorción de hidrógeno es menor que en el blanco original. Al volver a la oxidación de
etanol, la actividad sigue mostrándose pequeña debido a la desactivación de la superficie.
Por el contrario, un simple enjuague del electrodo con agua destilada provoca una
recuperación de la actividad inicial (Fig. 4.10), mostrando como la especie inhibidora es
Capítulo 4: Oxidación de etanol en electrodos monocristalinos de Pt: efecto de la estructura superficial en medio alcalino
128
estable a pHs alcalinos pero no en medio neutro. Si se realiza el mismo experimento con
acetaldehído, se observa que esta especie no se oxida en medio alcalino y produce un
bloqueo prácticamente instantáneo de la superficie. Por tanto, se puede pensar que la
especie inhibidora está relacionada con la producción de acetaldehído y a su posible
dimerización, que probablemente pueda dar lugar a la presencia de especies CHx en
superficie, como se propone en otros trabajos relacionados. El grado de desactivación entre
los tres planos bases es Pt(111) > Pt(110) > Pt(100), relacionado directamente con la
cantidad de acetaldehído formado en cada electrodo.
129
Chapter 4
This chapter has been adapted and formatted from ChemPhysChem 2014, 15, 2019-2028.
Corresponding author: [email protected]
Chapter 4: Ethanol oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium
130
4.1 Introduction
In the research of possible new fuels for developing fuel cell technology, the
oxidation of small organic molecules on pure platinum and alloys has been widely
examined in recent years [1]. In particular, ethanol is one of the most studied molecules
due to its advantages [2-5]. It is considered to be a ‘green’ chemical because it can be
obtained directly from biomass after distillation, it can be easily introduced in the current
fuel distribution system and it has a high energy density in the complete oxidation to CO2.
In this process 12 electrons are exchanged:
(4.1)
The thermodynamic standard potential of this reaction is 0.085 V, which yields a
standard cell potential for an ethanol/oxygen fuel cell of 1.145 V. However, there are some
problems which should be solved prior to practical use. These problems are related with
the slow kinetics of ethanol oxidation reaction that produce large overpotentials and
diminish the operational potential, and to the incomplete oxidation to acetic acid.
With platinum as a catalyst, studies clearly show that the surface structure is an
important parameter that significantly changes the reactivity for the oxidation of small
molecules [6-8]. This is the case of ethanol [5, 9]. In acid solutions, the proposed oxidation
mechanism has a dual route:
(4.2)
Reaction steps (1) and (2) represent the route for the incomplete oxidation of ethanol,
which produces acetaldehyde with two electrons transferred, and acetic acid by transferring
two additional electrons. This route should be avoided because acetic acid cannot be
oxidized at room temperature. Thus, only four electrons are exchanged and 2/3 of the
formal energy density of ethanol is not used. To give CO2 as the final product, it is
necessary to break the C-C bond through steps (3) and (4). The cleavage is followed by the
transformation of the fragments into adsorbed CO in step (5). CO is considered to be a
poison intermediate in many reactions because it is adsorbed strongly on the catalyst
Introduction
131
surface and is difficult to oxidize. For that reason, it inhibits further reactions. However,
for ethanol oxidation, it can be considered as a previous step in the complete oxidation to
CO2. In acid media and on Pt(111) electrodes, the reaction proceeds exclusively through
the route that gives acetic acid, whereas Pt(100) electrodes and the stepped surfaces with
110 steps and 111 terraces favor cleavage of C-C bond and the formation of CO [5, 9,
10]. In addition, foreign adatoms are used to promote complete oxidation to CO2, for
example, ruthenium, rhodium or tin [11-13].
Nowadays, research into alkaline fuel cells (AFCs) has regained momentum and the
alkaline environment has some advantages. Higher electrocatalytic currents are obtained in
comparison with acidic media and it has lower corrosive properties, which opens up the
possibility of using less expensive electrocatalysts [14]. However, the technology of AFCs
has to overcome two main problems: the carbonation of the system due to CO2 retention
and the difficulty of finding membranes that can sustain operation in alkaline conditions
over long periods of time. Nevertheless, new anion-exchange membranes have been
developed in recent years to solve these problems [15-17].
To understand the behavior of the possible electrocatalysts, fundamental studies are
required. However, there are few studies of ethanol oxidation in alkaline media on
platinum electrodes. In only a small number of papers, single-crystal electrodes [18, 19]
and polycrystalline surfaces [20, 21] have been used. In these investigations, it is clearly
stated that the preferred route for the oxidation is the one that leads to acetaldehyde-acetate
production. Additionally, there are some controversies with the oxidation mechanism
presented. Koper and Lai [19] observed the presence of COads on the platinum surface by
using Raman spectroscopy. Conversely, Christensen et.al [21] state that no COads occurs
during ethanol oxidation in this environment and they propose that the observed signals for
COads in FTIR are due to a pH changes in the thin layer, which shifts to neutral or acidic
values.
Herein, we report the influence of the surface structure of Pt single crystals for
ethanol oxidation in alkaline media. We used voltammetric and chronoamperometric
techniques to study the reactivity of the system and FTIR experiments to find intermediate
Chapter 4: Ethanol oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium
132
and final species formed during ethanol oxidation. These results were used to understand
the oxidation mechanism on the Pt surfaces.
Experimental section
133
4.2 Experimental Section
Platinum single-crystal electrodes were oriented, cut and polished from small single
crystal beads (≈2 mm in diameter for the voltammetric experiments and ≈4.5 mm for the
spectroelectrochemical measurements) by following the procedure described by Clavilier
and co-workers [22, 23]. The electrodes were cleaned by flame annealing for 30 s in an
oxygen/gas flame, cooled in a H2/Ar atmosphere and protected with water in equilibrium
with this gas mixture to prevent contamination before immersion in the electrochemical
cell, as described in detail elsewhere [23, 24]. The voltammetric profiles and, therefore, the
surface structure of the electrodes is stable upon cycling provided that oxide formation is
avoided.
Voltammetric and chronoamperometric measurements were carried out by using a
waveform generator (EG&EG PARC 175), together with a potentiostat (Amel Model
2053) equipped with ohmic drop compensation and a digital recorder (eDAQ ED401). For
the spectroelectrochemical measurements, a Nicolet 8700 spectrometer equipped with a
mercury cadmium telluride (MCT) detector was used. The spetroelectrochemical cell was
equipped with a CaF2 prism beveled at 60º [25, 26]. IR spectra were collected with a
resolution of 8 cm-1 and 100 interferograms for increasing the signal-to-noise ratio. A
p-polarized light was used in all FTIR experiments. The spectra are presented as
absorbance measurements (A=-log (R1-R2)/R1), where R2 and R1 are the reflectance values
for the single-beam spectra recorded at the sample and the reference potential, respectively.
Positive bands in the spectra correspond to species formed at the sample potential, whereas
negative bands are assigned to species consumed. The sample spectra were collected after
applying successive potential steps of 100 mV between 0.10 and 0.95 V. A reference
spectrum was always recorded at 0.10 V.
Ethanol oxidation experiments were performed in a 0.1 M NaOH + 0.2 M
CH3CH2OH solution, prepared by using ethanol absolute (Merck p.a.), NaOH (NaOH
monohydrate 99.99% Merck Suprapur) and ultrapure water (Elga Purelab Ultra 18.2 MΩ
cm). Ar (N50, Air Liquide) was used for deoxygenating the solutions. All the experiments
were carried out at RT in a three-electrode electrochemical cell. A platinum wire was used
Chapter 4: Ethanol oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium
134
as a counter-electrode and a reversible hydrogen (N50, Air Liquide) electrode was used as
the reference electrode (RHE).
Results
135
4.3 Results
4.3.1 Ethanol oxidation on Pt basal planes
Fig. 4.1 shows cyclic voltammetric profiles of Pt single-crystal electrodes with basal
orientation in alkaline medium, which are in agreement with previous results [27-32]. For
these surfaces, the signals appearing in the voltammograms are related to the hydrogen and
OH adsorption/desorption processes, in addition to double-layer contributions. These
processes are well separated for the Pt(111) electrode and the signals that correspond to
hydrogen adsorption can be found at potentials below 0.4 V, whereas OH adsorption
occurs at potentials above 0.6 V.
Fig. 4.1.Voltammetric profiles of the Pt(111), Pt(110) and Pt(100) electrodes in 0.1 M NaOH. Scan
rate: 0.05 V s-1.
-50
0
50
1000.0 0.2 0.4 0.6 0.8 1.0
-200
-100
0
100
200
0.0 0.2 0.4 0.6 0.8 1.0-100
-50
0
50
E/V
j/µA
cm-2
Pt(111)
j/µA
cm-2
Pt(110)
j/µA
cm-2
E/V
Pt(100)
Chapter 4: Ethanol oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium
136
For the other two basal planes, both processes overlap and competitive adsorption
between hydrogen and OH takes place. For the Pt(100) electrode, signals at potentials
below 0.4 V correspond mainly to the hydrogen adsorption processes, whereas OH
adsorption occurs mainly above this potential [29]. For the Pt(110) electrode, the peak at
0.27 V in the positive scan direction corresponds to the desorption of a monolayer of
hydrogen and the simultaneous adsorption of OH. Of course, the peak in the negative scan
direction at 0.25 V corresponds to the opposite process. When compared with acidic
solutions in absence of specific adsorption, that is, in perchloric acid solutions, OH and
hydrogen adsorption processes appear in a similar potential range in the RHE scale.
However, the detailed shape of the votammograms is markedly affected by the pH.
With ethanol oxidation in 0.1 M NaOH was studied, the measured oxidation currents
for the Pt(111) electrode were much higher than those recorded in acidic media (Fig 4.2).
The upper potential limit was adjusted to 0.95 V to avoid significant changes in the surface
structure due to oxide formation [33, 34].
Fig. 4.2. Voltammetric profiles of the Pt(111) electrode (1st cycle) in 0.1 M NaOH + 0.2 M EtOH with
(solid line) and without (dotted line) ohmic drop correction at 0.05 V s-1
When the initial voltammogram recorded without ohmic drop compensation (Fig.
4.2, dotted line) was compared with those presented in the literature, some differences
were found [18, 19]. Maximum currents and peak potentials were different depending on
the data source. Due to the large currents and the lower conductivity of the alkaline
solutions in comparison with acidic solutions, the ohmic drop in the electrolyte can affect
0.0 0.2 0.4 0.6 0.8 1.00
5
10
15
20
25
30
35
40
j/mA
cm-2
E/V
Results
137
the results. The total resistance of the present cell configuration is approximately 200 Ω
and the maximum current is around 1 mA. Thus, it is clear that the IR should be corrected
to obtain the right voltammogram [35]. It should be noted that resistance in the meniscus
can account for more than 80 % of the total resistance due to the small section of liquid in
this part. The resistance in the meniscus depends on the electrode area and the meniscus
high. Fig. 4.2 clearly shows the effect of ohmic drop correction in the ethanol voltammetric
profile on Pt(111) in alkaline medium. A well-defined peak at 0.82 V is observed and peak
currents as high as 37 mA cm-2 were recorded, significantly higher than those previously
reported in the literature [18, 19].
The voltammetric profile for the Pt(111) electrode presents two main characteristics:
it has low hysteresis between the positive and negative scan directions and the activity
diminishes drastically upon cycling (Fig. 4.3).
Fig. 4.3. Evolution of the voltammetric profile of the Pt(111), Pt(110) and Pt(100) electrodes upon
cycling in 0.1 M NaOH + 0.2 M EtOH at a scan rate of 0.05 V s-1.
0
20
400.0 0.2 0.4 0.6 0.8 1.0
E/V
j/mA
cm-2
1st cycle 2nd cycle 5th cycle 15th cycle 25th cycle
Pt(111)
0
5
10 Pt(110) 1st cycle 3rd cycle 5th cycle 7th cycle 10th cycle
j/mA
cm-2
0.0 0.2 0.4 0.6 0.8 1.0
0
1
2Pt(100) 1st cycle
3rd cycle 5th cycle 7th cycle 10th cycle
j/mA
cm-2
E/V
Chapter 4: Ethanol oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium
138
In the oxidation of small organic molecules, the hysteresis is normally related to the
formation and adsorption of CO at low potentials, which is only oxidized above 0.7 V [36].
The small hysteresis would then indicate that the total amount of CO formed and
accumulated on the surface is very small. However, the deactivation is very significant and
after 25 cycles the peak current is only a 20th of that measured in the first cycle. It should
be remarked that the deactivation depends on the upper potential limit. When the upper
potential limit is set below 0.7 V, the activity remains almost constant upon cycling (not
shown).
For the other two basal planes, the activity is much lower (Fig. 4.3). For the Pt(110)
electrode, the maximum current is approximately 10 mA cm-2, whereas only 2 mA cm-2
was measured for the Pt(100) electrode. In both cases, there is a clear hysteresis in the
currents and peak potentials. However, this hysteresis is not the typical one associated with
the formation and adsorption of CO at low potentials. When CO is accumulated on the
surface, as occurs during the oxidation of ethanol or methanol in acid media [5, 37], the
currents in the positive scan direction are significantly smaller than those measured in the
negative scan direction. Here, peak currents in the positive scan direction are at least as
high as those in the negative scan direction. Nevertheless, there is a significant shift in the
region were currents are recorded. This is clearly the case for the Pt(100) electrode; in the
positive scan direction, the activity for the oxidation of ethanol is obtained between 0.6 and
0.9 V and the peak current is located at 0.75 V, whereas currents for the negative scan
direction are measured between 0.8 and 0.45 V with a peak potential at 0.53 V.
Additionally, the deactivation upon cycling is negligible for the Pt(100) electrode.
However, a significant deactivation is observed for the Pt(110) electrode, although to a
lesser extent than that for the aforementioned Pt(111) electrode.
It should be highlighted that the activity order for the low index planes is just the
opposite of that observed in acidic media. In this media, the order of peak currents is
Pt(100) > Pt(110) > Pt(111) whereas in alkaline solutions the order is Pt(111) > Pt(110) >
Pt(100). Another important difference is onset potential. In acid solution, the lower onset
for the oxidation is observed for the Pt(111) electrode, whereas in alkaline media the lower
onset is for the Pt(110) electrode.
Results
139
To obtain more information the ethanol-oxidation reaction on those electrodes,
chronoamperometric experiments were carried out. Fig. 4.4 shows the transients measured
at 0.6 V for the basal planes for 10 minutes. This potential was chosen because it is a
potential where ethanol oxidation has started but currents are low and are not controlled by
the transport limitations of ethanol. The decay in the transients should be related to the
presence of adsorbed species blocking the catalytic surface. The currents measured at 0.6
V follow the expected behavior from the currents measured in the voltammetric profiles at
0.6 V. Thus, the largest currents were measured for the Pt(110) electrode and the lowest for
the Pt(111) electrode. For all the electrodes, a decrease in the currents was observed and is
proportionally larger for the Pt(110) electrode. As aforementioned, this decay is not related
to diffusion problems because the expected limiting diffusion current is more than 10 times
larger than that measured here. Additionally, the transient for the Pt(100) electrode shows a
small increase in the currents at short times. This process is related to the hysteresis
observed in the voltammogram. At 0.6 V, currents in the negative scan direction are larger
than those in the positive scan direction. Because the transients were recorded after
stepping the electrode from 0.1 V, the initial currents are close to those measured in the
positive scan direction at this potential. The current increase is then related to the
difference with the negative scan direction. In fact, if the potential is halted at 0.6 V in the
positive scan direction during the recording of a voltammogram, the currents increase to
reach values close to those measured in the negative scan direction.
Fig. 4.4. Chronoamperometric transient at 0.6 V for ethanol oxidation on the Pt(111), Pt(110) and
Pt(100) electrodes in 0.1 M NaOH + 0.2 M EtOH.
0 100 200 300 400 500 6000
1000
2000
3000
4000
5000
400 500 6000
100
200
300
400
500
j/µA
cm-2
t/s
j/µA
cm-2
t/s
Pt(111) Pt(110) Pt(100)
Chapter 4: Ethanol oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium
140
In acidic solutions, it has been found that the presence of steps in the 111
symmetry terrace catalyze the cleavage of the C-C bond [9-12], which is the key step in the
mechanism for the oxidation of ethanol to CO2 (or carbonate in alkaline solutions) and
higher currents are measured for those electrodes. For that reason, it is interesting to study
the effects of steps on the reactivity of the 111 terraces for ethanol oxidation. Fig. 4.5
shows voltammetric profiles for Pt stepped electrodes.
Fig. 4.5. Voltammetric profiles (1st cycle) for Pt stepped electrodes Pt(n,n,n-2) and Pt(n+1,n-1,n-1) in
0.1 M NaOH + 0.2 M EtOH at 0.05 V s-1.
Two series of stepped surfaces that contained 111 terraces and 110 or 100
steps were studied. These surfaces are named Pt(s) [(n-1) (111)×(110)]= Pt(n,n,n-2) for the
surfaces with (110) steps and Pt(s)[n(111)×(100)]= Pt(n+1, n-1, n-1), for the surfaces with
100 steps. In these notations, n represents the number of rows in the 111 terrace. For
both series, the presence of steps on the 111 terrace does not improve peak current
densities, as can be observed in Fig. 4.5. However, the onset potential for the oxidation is
0
5
10
15
20
25
30
35
400.0 0.2 0.4 0.6 0.8 1.0
E/V
j/mA
cm-2
Pt (111) Pt (15 15 14) Pt (554) Pt (775) Pt (553)
0.0 0.2 0.4 0.6 0.8 1.00
5
10
15
20
25
30
35
j/mA
cm-2
E/V
Pt (111) Pt (15 14 14) Pt (544) Pt (755) Pt (533)
Results
141
displaced towards more negative potentials and the hysteresis between positive and
negative scan directions increases. In fact, the behavior of the surfaces with high step
density, namely, Pt(553) and Pt(533) electrodes, begin to resemble that of the 110 and
100 surfaces, respectively. In fact, the Pt(533) electrode shows, in the negative scan
direction, significant currents up to 0.35 V.
From these results, it is clear that the activity of these stepped surfaces at high
potentials (E>0.6 V) is dominated by the presence of the 111 terraces, whereas the
activity at low potentials is dominated by the presence of the steps. In this sense, it can be
said that the activity of the 100 step is higher than that of the 110 step because
currents for comparable step densities in this region are larger in the negative scan
direction. To demonstrate this effect, chronoamperometric transients for these series of
surfaces were also recorded at 0.6 V (Fig. 4.6).
Fig. 4.6. Chronoamperometric transient at 0.6 V for Pt stepped electrodes Pt(n,n,n-2) and Pt(n+1,n-
1,n-1) in 0.1 M NaOH + 0.2 M EtOH.
As can be seen, the initial current for the series with 110 steps is larger but the
current density decays very fast. On the other hand, for the surfaces with 100 steps, the
initial current is smaller but the decay is also smaller and, in some cases, an increase in the
0
1000
2000
3000
4000
5000
6000
400 500 600
100
200
300
400
500
j/µA
s-1
t/s
j/µA
cm-2
Pt (111) Pt (15 15 14) Pt (554) Pt (775) Pt (553)
0 100 200 300 400 500 6000
1000
2000
3000
4000
400 500 6000
100
200
300
400
500
j/µA
s-1
t/s
j/µA
cm-2
t/s
Pt (111) Pt (15 14 14) Pt (544) Pt (755) Pt (533)
Chapter 4: Ethanol oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium
142
currents is observed. This current increase is especially important for surfaces with a high
100 step density, that is, the Pt(533) surface. As in the case of the Pt(100) surface, the
increase has the same origin as the hysteresis observed for the cyclic voltammogram
between the positive and negative scan directions. When the activity of the 110 and
100 steps is compared with that of the low-index planes, it can be said that the activity of
the (100) step is larger than that measured for the Pt(100) electrode at this potential, as Fig.
4.6 demonstrates. On the other hand, the activity of the 110 step is similar to that of the
Pt(110) low-index plane. Thus, the activity order at long times at 0.6 V is the following
100 step > 110 terrace – 110 step > 100 terrace > 111 terrace. The order of
reactivity for the steps is also the opposite to that found in acidic media because 110
steps are more reactive in this reaction than 100 steps [9].
4.3.2 FTIR experiments of ethanol oxidation
To find information about the adsorbates and final products formed during the
ethanol-oxidation reaction in alkaline medium, FTIR experiments were carried out. Fig.
4.7 shows reference spectra in alkaline solutions for acetate and carbonate, two of the
possible final products.
Fig. 4.7. Transmission spectra of 0.2 M acetate and 0.2 M carbonate in 0.1 M NaOH. The spectra of
the Pt(111) electrode at 0.8 V in 0.2 M EtOH + 0.1 M NaOH is also shown with its adjusted spectra by using
a linear combination of the carbonate and acetate spectra.
2400 2200 2000 1800 1600 1400 1200
2400 2200 2000 1800 1600 1400 1200
υ/cm-1
A: Sodium carbonate
B: Sodium acetate
0.25 A + 1.53 B
Spectra 'in situ' Pt (111)
Results
143
It should be mentioned that it is not possible to measure the spectra of acetaldehyde
(another possible product) in alkaline solutions because acetaldehyde readily polymerizes
through an aldol condensation in this medium. According to the literature [5, 21, 38], the
bands at 1550 and 1415 cm-1 for acetate correspond to the O-C-O asymmetric and
symmetric stretching vibrational modes, respectively. The band at 1390 cm-1 for carbonate
is also related to the O-C-O vibrational mode.
For the different electrodes, the spectra at different electrode potentials are shown in
Fig. 4.8.
Fig. 4.8. FTIR spectra at different potentials for the Pt(111), Pt(110) and Pt(100) electrodes in 0,2 M
EtOH + 0.1 M NaOH. Reference spectra taken at 0.1 V.
2400 2200 2000 1800 1600 1400 1200
2400 2200 2000 1800 1600 1400 1200
2400 2200 2000 1800 1600 1400 1200
2400 2200 2000 1800 1600 1400 1200
2400 2200 2000 1800 1600 1400 1200
2400 2200 2000 1800 1600 1400 1200
Pt (100)
Pt (110)
0,6 V0,7 V0,8 V0,9 V
0,95 V
0,2 V0,3 V0,4 V0,5 V
Pt (111)
0,6 V0,7 V0,8 V
0,9 V
0,95 V
0,2 V0,3 V0,4 V0,5 V
υ/cm-1
0,6 V0,7 V0,8 V
0,9 V
0,95 V
0,2 V0,3 V0,4 V0,5 V
Chapter 4: Ethanol oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium
144
As can be seen, only acetate bands are visible. It should be highlighted that the band
related to adsorbed CO at low potentials cannot be detected. Adsorbed CO on Pt electrodes
in alkaline media shows strong bands at approximately 2030 cm-1 [39], and this band is not
visible in the spectra of all the studied electrodes, even stepped electrodes. As mentioned,
110 steps are very active for the cleavage of the C-C bond at low potentials, which
produces adsorbed CO in acid solutions [9, 10]. At high potentials, a very small band at
2340 cm-1 associated to CO2 can be observed. The presence of this band is indicative of a
large shift in the pH of the thin layer used for the spectra acquisition, due to the oxidation
of ethanol trough the reactions of Eq. (4.2). Finally, the small band present at 1350 cm-1 is
assigned to also the acetate group, in accordance with experiments by Zhou et al. [38].
In these spectra, the presence of carbonate cannot be discarded a priori because the
carbonate band at 1390 cm-1 overlaps with the band of acetate at 1415 cm-1 [29, 40], which
makes it difficult to correctly determine the CO2/acetate ratio. For this reason, the
reference spectra of carbonate and acetate (Fig. 4.7) were used to fit the measured spectra
for the different electrodes [38]. The fitting was done in the spectral region between 1260
and 1615 cm-1 by using the spectra for acetate and carbonate as input functions and two
adjustable parameters in the following expression:
ν ν ν= ⋅ + ⋅f( ) g( ) h( )a b (4.3)
in which g(ν) and h(ν) are the spectra of acetate and carbonate, respectively, a and b two
adjustable parameters and f(ν) is the fitting function, which is compared with the
experimental spectra for the different electrodes. A least-squares method was used to
determine the two adjustable parameters. The spectra for the Pt(111) at 0.8 V and the
calculated fitting are also shown in Fig. 4.7. The results for the fittings are presented in
Table 4.1. As can be seen, the amount of carbonate produced in all cases is low, even for
the stepped surfaces that are quite active for the formation of CO2 in acidic solutions. Only
for the Pt(111) electrode can some carbonate be detected (≈14%). This carbonate has been
formed above 0.6 V because no CO is detected below this potential. Thus, it can be
concluded that the main products of the oxidation in this medium are acetate and
acetaldehyde. These results are in agreement with the absence of CO adsorption bands at
low potentials and the results obtained by Christensen et. al. [21] with polycrystalline
electrodes, and suggest that the presence of CO and CO2 bands are due to depletion of OH-
Results
145
in the thin layer, which causes a variation of pH. Thus the preferred route is the incomplete
oxidation to acetate.
Electrode Acetate Carbonate
Pt(111) 1.53 0.25
Pt(110) 1.22 0.05
Pt(100) 1.39 0.00
Table 4.1. Adjust parameters for the acetate and carbonate spectra for the fitting of the spectra of the
different electrodes at 0.8 V.
Chapter 4: Ethanol oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium
146
4.4 Discussion
From the results reported above, it is clear that the main product of ethanol oxidation
in alkaline solutions is acetate (and possibly acetaldehyde), although the cleavage of the C-
C bond to give CO and CO2 cannot be completely discarded. Thus, it is important to
understand the origin of the significant differences when the behavior of these electrodes is
compared to that observed in acidic solutions. First, the high activity of the Pt(111)
electrode in alkaline media is clearly associated with a large production of acetic acid. In
perchloric acid solutions, chronoamperometric results also indicate that the activity for
acetic acid production is very high at very short times [5]. However, the newly formed
acetic acid molecules adsorb immediately on the electrode surface as acetate and inhibit
the reaction. In fact, it can be considered a self-poisoned reaction [5]. In alkaline media,
the activity is also very high, but acetate adsorption does not occur because the absolute
potential is approximately 0.7 V more negative. Thus, the reaction can proceed at a high
rate without any obstacle.
Although the reaction on the Pt(111) electrode follows the same mechanism in both
media and gives mainly acetic acid (or acetate, depending on the pH) at a very high rate,
there is an important difference in the onset potential on the RHE scale. In acidic media,
the recorded onset for ethanol oxidation is as low as 0.4 V [5], but in alkaline solutions it is
above 0.6 V, the region at which OH adsorption on the 111 terrace occurs. In the
oxidation of ethanol to acetic acid, an oxygen group should be transferred to the ethanol
molecule to give rise to the carboxylic group. This fact suggests that the oxidation process
in alkaline solutions is triggered by the adsorption of OH on the surface, which is
transferred to the ethanol molecule. However, in acidic solutions, adsorbed OH is not
required because the onset for oxidation is at potentials below OH adsorption. In these later
media, adsorbed water should then transfer the oxygen group to the ethanol molecule.
These changes point to significant differences in the interfacial water properties (and/or
adsorbed OH) between acidic and alkaline interfaces, which are probably related to the
different absolute potential. Similar conclusions have been obtained when the reactivity of
the single-crystal electrodes for the oxygen reduction reaction was studied in acidic and
alkaline solutions [41]. For this reaction, the reactivity order in acidic and alkaline media
are also completely different. Thus, it can be concluded that the different water structure at
Discussion
147
different pH values and/or the absolute electrode potential significantly affect the reactivity
of the species in the interfacial region.
With acetate as the major product, the effect of adsorbed OH can also explain the
lower onset for ethanol oxidation for the other basal planes and stepped surfaces in 0.1 M
NaOH. The onset for OH adsorption on the Pt(100) and Pt(110) is well below 0.6 V and,
therefore, the effective transfer of OH to the ethanol molecule can occur at lower
potentials. For Pt(100), the onset in the negative scan direction is at approximately 0.4 V,
which coincides with the initial potential for OH adsorption on this plane. For the (110)
surface, the onset is even lower in the negative scan direction and in this plane, OH
adsorption occurs at potentials as low as 0.26 V.
Another important characteristic of the voltammetric profiles of all the electrodes
studied here (except the Pt(111) electrode) is that the large hysteresis is not related to the
formation of CO, as mentioned earlier. By using Raman spectra and polycrystalline
electrodes Koper and co-worker proposed that CHx species are adsorbed on the electrode
surface [19] and these species could be the origin of the hysteresis. They are formed at low
potential and partially block the surface, which inhibits the oxidation, and are oxidized at
high potentials. However, spectroscopic signals for these adsorbed species are not
accessible in infrared due to the interference of the window material in the spectral region
of interest. For that reason, it is not possible to validate this hypothesis, although the
possible origin of signals corresponding to CHx species will be discussed below. However,
if the oxidation is linked to the presence of OH on the surface, it is also possible that the
hysteresis could be related to some irreversibility in the OH adsorption. In acid media, OH
adsorption processes are completely reversible at 50 mV/s, which gives rise to a
symmetrical voltammetric profile. In alkaline solutions, some irreversibility is observed
because the peak potentials for OH adsorption on the Pt(100) and Pt(110) electrodes is not
same in both scan directions. Thus, it is possible that the presence of ethanol increases the
irreversibility of this process and gives rise to a large hysteresis.
Another problem in the oxidation of ethanol in alkaline media is the fast deactivation
of the surface. This process cannot be linked to the formation of CO because it has not
been detected on the surface and would have been completely oxidized at the upper
Chapter 4: Ethanol oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium
148
potential limit. Thus, another species, which could not be detected by IR, is responsible for
the deactivation of the surface. It should be borne in mind that the spectrum for
acetaldehyde could not be measured in alkaline solutions due to its reactivity, and for that
reason acetaldehyde formation cannot be detected. However, during the oxidation of
ethanol to acetic acid in acidic media, acetaldehyde is always formed. Therefore, in
alkaline media, it can be proposed that acetaldehyde is also produced, and this molecule
could be the cause of the deactivation after polymerization.
To determine the electrochemical properties of this blocking species, and the role of
ethanol and acetaldehyde in this process, different voltammetric experiments with ethanol
and acetaldehyde were carried out. In the first experiment, four voltammetric cycles for
ethanol oxidation were recorded for the Pt(111) electrode (which has the highest
deactivation rate) in 0.1 M NaOH + 0.2 M EtOH (Fig. 4.9A, dashed lines). After the fourth
cycle, a clear deactivation of the surface was observed. Then the electrode was transferred
to a cell containing only 0.1 M NaOH and the voltammetric profile was recorded and
compared with that obtained for a newly prepared Pt(111) surface (Fig. 4.9B). As can be
seen, after recording the ethanol oxidation curves, the surface is partially blocked by some
species, because the hydrogen and OH adsorption charges are smaller than those measured
for a clean Pt(111) electrode.
In the initial cycle, there is still some ethanol close to the interface and the extra
current recorded at E>0.6 V in the first cycle is due to the oxidation of trace ethanol.
However, the voltammogram is stable upon cycling and the blocking species cannot be
removed if the electrode is cycled up to 0.9 V, even if the lower potential limit is set in the
hydrogen evolution region (not shown). Once the profiles in the blank electrolyte were
recorded, the electrode was transferred back to the solution that contained ethanol (Fig.
4.9A, solid line). As can be seen, the voltammetric profile corresponds to the one that
would have been obtained without the transfer experiment, that is, the profile corresponds
to the fifth cycle. Taking into account that the deactivation is linked to the oxidation of
ethanol, the species responsible for this deactivation is stable on the surface and does not
suffer any oxidation or reduction process at E < 0.95 V.
Discussion
149
Fig. 4.9. A) Voltammetric profile of a Pt(111) electrode in 0.1 M NaOH + 0.2 M EtOH: Black and red
dashed lines: 1st and 4th cycle. Solid line: initial cycle after recording experiment in panel B. B) Voltammetric
profile of a Pt(111) electrode in 0.1 M NaOH after recording the 4th cycle in A). The voltammetric profile of
a clean Pt(111) electrode is also shown for comparison (green line). Scan rate 0.05 V s-1.
If the experiment is repeated but includes a rinsing step with water after recording
the ethanol-oxidation cycles, the curves shown in Fig. 4.10 are obtained. As can be seen,
after rinsing the electrode with water, the blocking species were completely removed and
the voltammogram of a clean Pt(111) electrode is immediately recovered. Moreover, the
initial activity of the electrode for ethanol oxidation is also recovered, as demonstrated by
the voltammetric profile of the electrode after re-immersion of the electrode in the ethanol-
containing solution. This experiment indicates that the blocking species does not survive at
neutral pH values.
0
5
10
15
20
25
30
35
400.0 0.2 0.4 0.6 0.8 1.0
j/mA
cm-2
1st cycle 4th cycle After transfer experiment
A
0.0 0.2 0.4 0.6 0.8 1.0
-100
-50
0
50
100 B 1st cycle 5th cycle Clean Pt(111)
j/µA
cm-2
E/V
Chapter 4: Ethanol oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium
150
Fig. 4.10. A) Voltammetric profile of a Pt(111) electrode in 0.1 M NaOH + 0.2 M EtOH: Black and
red dashed lines: 1st and 4th cycle. Full line, initial cycle after recording experiment in panel B. B)
Voltammetric profile of a Pt(111) electrode in 0.1 M NaOH after recording the 4th cycle in A) and rinsing the
electrode with water. The voltammetric profile of a clean Pt(111) electrode is also shown for comparison
(green line). Scan rate 0.05 V s-1.
To determine the role of acetaldehyde, the same experiments as in Fig. 4.9 and Fig.
4.10 were performed, but by using a 0.1 M NaOH + 0.2 M acetaldehyde solution. As can
be seen in Fig. 4.11, acetaldehyde is not oxidized in this medium and the surface becomes
instantly blocked by adsorbed species. When the electrode is transferred to the cell that
contained 0.1 M NaOH, the surface was almost completely deactivated and the adsorbed
species were not oxidized or reduced. Only rinsing the electrode with water removed the
blocking species, in the same way as observed in Fig. 4.10. Thus, it is clear that the
decrease in activity is linked to the production of acetaldehyde. Probably, as soon
0
5
10
15
20
25
30
35
400.0 0.2 0.4 0.6 0.8 1.0
j/mA
cm-2
1st cycle 4th cycle After transfer experiment
A
0.0 0.2 0.4 0.6 0.8 1.0
-50
0
50
B 1st cycle 2nd cycle Clean Pt(111)
j/µA
cm-2
E/V
Discussion
151
acetaldehyde is produced, it readily dimerizes and adsorbs on the surface and hinders the
ethanol-oxidation reaction.
Fig. 4.11. A) Voltammetric profile of a Pt(111) electrode in 0.1 M NaOH after recording the
voltammetric profiles in the inset. Inset: Voltammetric profile of a Pt(111) electrode in 0.1 M NaOH + 0.2 M
acetaldehyde. B) As for A), but the electrode was rinsed prior to immersion in the cell that contained 0.1 M
NaOH.
This blocking mechanism also explains why the decrease of current upon cycling
follows the order Pt(111) > Pt(110) > Pt(100). This order is also the order of maximum
currents. If the inhibition is linked to the formation of acetaldehyde, the higher the currents
for the oxidation of ethanol are, the higher the amounts of acetaldehyde that are formed.
Thus, when the Pt(111) electrode is cycled up to 0.65 V, with low oxidation currents, the
poisoning of the electrode is very small and no poisoning is recorded. Also, it is in
-50
0
50
100
0.0 0.2 0.4 0.6 0.8 1.0
B
E/V
j/µA
cm-2
1st cycle 5th cycle 10th cycle 16th cycle
A
0.0 0.2 0.4 0.6 0.8 1.0
-50
0
50
100
j/µA
cm-2
E/V
1st cycle 2nd cycle 5th cycle
0.0 0.5 1.0
-50
0
50
1st cycle 7th cycle
j/µA
cm-2
E/V
0.0 0.2 0.4 0.6 0.8 1.0
-50
0
50
1st cycle 5th cyclej/µ
A cm
-2
E/V
Chapter 4: Ethanol oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium
152
agreement with the Raman experiments [19], from which adsorbed CHx is proposed as the
inhibiting species. The CHx is clearly present in acetaldehyde or any polymerization
product and can adsorb on the electrode surface. This fact also explains why it has been
proposed that the adsorption of CHx occurs particularly in the 111 domains, because that
domain has higher oxidation currents. As has been shown by using both voltammetry and
chronoamperometry, the higher the currents are, the faster the deactivation is observed.
Conclusions
153
4.5 Conclusions
The results presented here clearly show that the reactivity of platinum electrodes for
ethanol oxidation is affected by the solution pH. The solution pH alters the water structure
of the interfacial region and also the absolute potential range in which the oxidation occurs.
Both factors clearly change the reactivity of platinum. In alkaline solutions, higher peak
currents are measured, although the selectivity for CO2 production is much lower.
Additionally, the surfaces deactivate fast due to the production of acetaldehyde, which
readily polymerizes in this medium, adsorbs on the electrode surface, and prevents further
reaction.
Chapter 4: Ethanol oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium
154
4.6 References
[1] M. T. M. Koper, ''Fuel Cell Catalysis: A Surface Science Approach'', Electrocatalysis and Electrochemistry A. Wieckowski (Ed.), John Wiley & Sons, Hoboken, New Jersey, 2009.
[2] E. Antolini, ''Catalysts for direct ethanol fuel cells'' Journal of Power Sources 2007, 170, 1-12.
[3] W. Zhou, Z. Zhou, S. Song, W. Li, G. Sun, P. Tsiakaras and Q. Xin, ''Pt based anode catalysts for direct ethanol fuel cells'' Applied Catalysis B: Environmental 2003, 46, 273-285.
[4] C. Lamy, S. Rousseau, E. M. Belgsir, C. Coutanceau and J. M. Léger, ''Recent progress in the direct ethanol fuel cell: development of new platinum-tin electrocatalysts'' Electrochimica Acta 2004, 49, 3901-3908.
[5] F. Colmati, G. Tremiliosi-Filho, E. R. Gonzalez, A. Berná, E. Herrero and J. M. Feliu, ''Surface structure effects on the electrochemical oxidation of ethanol on platinum single crystal electrodes'' Faraday Discussions 2008, 140, 379-397.
[6] N. M. Markovic and P. N. Ross, ''Surface science studies of model fuel cell electrocatalysts'' Surface Science Reports 2002, 45, 117-229.
[7] V. Grozovski, V. Climent, E. Herrero and J. M. Feliu, ''The role of the surface structure in the oxidation mechanism of methanol'' Journal of Electroanalytical Chemistry 2011, 662, 43-51.
[8] C. Lamy, J. M. Léger, J. Clavilier and R. Parsons, ''Structural effects in electrocatalysis: A comparative study of the oxidation of CO, HCOOH and CH3OH on single crystal Pt electrodes'' Journal of Electroanalytical Chemistry 1983, 150, 71-77.
[9] F. Colmati, G. Tremiliosi-Filho, E. R. Gonzalez, A. Berná, E. Herrero and J. M. Feliu, ''The role of the steps in the cleavage of the C-C bond during ethanol oxidation on platinum electrodes'' Physical Chemistry Chemical Physics 2009, 11, 9114-9123.
[10] J. Souza-Garcia, E. Herrero and J. M. Feliu, ''Breaking the C-C Bond in the Ethanol Oxidation Reaction on Platinum Electrodes: Effect of Steps and Ruthenium Adatoms'' ChemPhysChem 2010, 11, 1391-1394.
[11] V. Del Colle, A. Berná, G. Tremiliosi-Filho, E. Herrero and J. M. Feliu, ''Ethanol electrooxidation onto stepped surfaces modified by Ru deposition: electrochemical and spectroscopic studies'' Physical Chemistry Chemical Physics 2008, 10, 3766-3773.
[12] V. Del Colle, J. Souza-Garcia, G. Tremiliosi-Filho, E. Herrero and J. M. Feliu, ''Electrochemical and spectroscopic studies of ethanol oxidation on Pt stepped surfaces modified by tin adatoms'' Physical Chemistry Chemical Physics 2011, 13, 12163-12172.
[13] J. P. I. de Souza, S. L. Queiroz, K. Bergamaski, E. R. Gonzalez and F. C. Nart, ''Electro-oxidation of ethanol on Pt, Rh, and PtRh electrodes. A study using DEMS and in-situ FTIR techniques'' Journal of Physical Chemistry B 2002, 106, 9825-9830.
[14] E. Antolini and E. R. Gonzalez, ''Alkaline direct alcohol fuel cells'' Journal of Power Sources 2010, 195, 3431-3450.
[15] J. S. Spendelow and A. Wieckowski, ''Electrocatalysis of oxygen reduction and small alcohol oxidation in alkaline media'' Physical Chemistry Chemical Physics 2007, 9, 2654-2675.
[16] J. R. Varcoe, R. C. T. Slade, E. L. H. Yee, S. D. Poynton, D. J. Driscoll and D. C. Apperley, ''Poly(ethylene-co-tetrafluoroethylene)-derived radiation-grafted anion-exchange membrane with properties specifically tailored for application in metal-cation-free alkaline polymer electrolyte fuel cells'' Chemistry of Materials 2007, 19, 2686-2693.
[17] C. Coutanceau, L. Demarconnay, C. Lamy and J. M. Léger, ''Development of electrocatalysts for solid alkaline fuel cell (SAFC)'' Journal of Power Sources 2006, 156, 14-19.
[18] M. López-Atalaya, E. Morallón, F. Cases, J. L. Vázquez and J. M. Pérez, ''Electrochemical oxidation of ethanol on Pt(hkl) basal surfaces in NaOH and Na2CO3 media'' Journal of Power Sources 1994, 52, 109-117.
References
155
[19] S. C. S. Lai and M. T. M. Koper, ''Ethanol electro-oxidation on platinum in alkaline media'' Physical Chemistry Chemical Physics 2009, 11, 10446-10456.
[20] B. Pierozynski, ''On the Ethanol Electrooxidation Reaction on Catalytic Surfaces of Pt in 0.1 M NaOH'' International Journal of Electrochemical Science 2012, 7, 4261-4271.
[21] P. A. Christensen, S. W. M. Jones and A. Hamnett, ''In Situ FTIR Studies of Ethanol Oxidation at Polycrystalline Pt in Alkaline Solution'' Journal of Physical Chemistry C 2012, 116, 24681-24689.
[22] J. Clavilier, D. Armand, S. G. Sun and M. Petit, ''Electrochemical adsorption behaviour of platinum stepped surfaces in sulphuric acid solutions'' Journal of Electroanalytical Chemistry 1986, 205, 267-277.
[23] C. Korzeniewski, V. Climent and J. M. Feliu, ''Electrochemistry at Platinum Single Crystal Electrodes'', in Electroanalytical Chemistry: A Series of Advances, vol. 24, A. J. Bard and C. Zoski (Eds.) CRC Press, Boca Ratón, 2012, pp. 75-169.
[24] A. Rodes, K. El Achi, M. A. Zamakhchari and J. Clavilier, ''Hydrogen probing of step and terrace sites on Pt(S)-[n(111) × (100)]'' Journal of Electroanalytical Chemistry 1990, 284, 245-253.
[25] T. Iwasita, F. C. Nart and W. Vielstich, ''An FTIR study of the catalytic activity of a 85:15 Pt:Ru alloy for methanol oxidation'' Berichte der Bunsen-Gesellschaft fuer Physikalische Chemie 1990, 94, 1030-1034.
[26] A. Rodes, J. M. Pérez and A. Aldaz, ''Vibrational spectroscopy'', in Handbook of Fuel Cells - Fundamentals, Technology and Applications, vol. 2, W. Vielstich, A. Lamm and H. A. Gasteiger (Eds.) Wiley, Chichester, 2003, pp. 191-219.
[27] F. J. Vidal-Iglesias, N. García-Aráez, V. Montiel, J. M. Feliu and A. Aldaz, ''Selective electrocatalysis of ammonia oxidation on Pt(100) sites in alkaline medium'' Electrochemistry Communications 2003, 5, 22-26.
[28] J. S. Spendelow, J. D. Goodpaster, P. J. A. Kenis and A. Wieckowski, ''Mechanism of CO oxidation on Pt(111) in alkaline media'' Journal of Physical Chemistry B 2006, 110, 9545-9555.
[29] R. M. Arán-Ais, M. C. Figueiredo, F. J. Vidal-Iglesias, V. Climent, E. Herrero and J. M. Feliu, ''On the behavior of the Pt(100) and vicinal surfaces in alkaline media'' Electrochimica Acta 2011, 58, 184-192.
[30] P. Rodríguez, G. García, E. Herrero, J. Feliu and M. Koper, ''Effect of the Surface Structure of Pt(100) and Pt(110) on the Oxidation of Carbon Monoxide in Alkaline Solution: an FTIR and Electrochemical Study'' Electrocatalysis 2011, 2, 242-253.
[31] E. Morallón, J. L. Vázquez and A. Aldaz, ''Electrochemical-Behavior of Basal Single-Crystal Pt Electrodes in Alkaline-Medium'' Journal of Electroanalytical Chemistry 1990, 288, 217-228.
[32] N. S. Marinkovic, N. M. Markovic and R. R. Adzic, ''Hydrogen Adsorption on Single-Crystal Platinum-Electrodes in Alkaline-Solutions'' Journal of Electroanalytical Chemistry 1992, 330, 433-452.
[33] A. Björling, E. Herrero and J. M. Feliu, ''Electrochemical Oxidation of Pt(111) Vicinal Surfaces: Effects of Surface Structure and Specific Anion Adsorption'' Journal of Physical Chemistry C 2011, 115, 15509-15515.
[34] A. Björling and J. M. Feliu, ''Electrochemical surface reordering of Pt(111): A quantification of the place-exchange process'' Journal of Electroanalytical Chemistry 2011, 662, 17-24.
[35] I. Z. Kiss, E. Sitta and H. Varela, ''On the Limit of Frequency of Electrochemical Oscillators and Its Relationship to Kinetic Parameters'' Journal of Physical Chemistry C 2012, 116, 9561-9567.
[36] M. T. M. Koper, S. C. S. Lai and E. Herrero, ''Mechanisms of the Oxidation of Carbon Monoxide and Small Organic Molecules at Metal Electrodes'', in Fuel Cell Catalysis, A Surface Science Approach, M. T. M. Koper (Ed.) John Wiley & Sons, Inc, Hoboken, NJ, 2009, pp. 159-208.
[37] E. Herrero, K. Franaszczuk and A. Wieckowski, ''Electrochemistry of Methanol at Low Index Crystal Planes of Platinum: An Integrated Voltammetric and Chronoamperometric Study'' Journal of Physical Chemistry 1994, 98, 5074-5083.
Chapter 4: Ethanol oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium
156
[38] Z.-Y. Zhou, Q. Wang, J.-L. Lin, N. Tian and S.-G. Sun, ''In situ FTIR spectroscopic studies of electrooxidation of ethanol on Pd electrode in alkaline media'' Electrochimica Acta 2010, 55, 7995-7999.
[39] M. J. S. Farias, C. Busó-Rogero, R. Gisbert, E. Herrero and J. M. Feliu, ''Influence of the CO Adsorption Environment on Its Reactivity with (111) Terrace Sites in Stepped Pt Electrodes under Alkaline Media'' The Journal of Physical Chemistry C 2013, 118, 1925-1934.
[40] T. Iwasita, A. Rodes and E. Pastor, ''Vibrational Spectroscopy of Carbonate Adsorbed on Pt(111) and Pt(110) Single-Crystal Electrodes'' Journal of Electroanalytical Chemistry 1995, 383, 181-189.
[41] R. Rizo, E. Herrero and J. M. Feliu, ''Oxygen reduction reaction on stepped platinum surfaces in alkaline media'' Physical Chemistry Chemical Physics 2013, 15, 15416-15425.
Capítulo 5: Oxidación de etanol en nanopartículas de platino: efecto de
la estructura superficial y de la agregación en medio alcalino
159
Capítulo 5: Oxidación de etanol en nanopartículas de
platino: efecto de la estructura superficial y de la
agregación en medio alcalino
RESUMEN
El objetivo de este capítulo es estudiar la oxidación de etanol en 0.1 M NaOH con
nanopartículas de platino, un sistema más útil desde un punto de vista aplicado, incidiendo
en el efecto de la estructura superficial (empleando las mismas muestras del capítulo 2),
además de un estudio de la aglomeración de partículas esféricas soportadas en carbón, que
provocan dificultades en la difusión del etanol sobre el catalizador.
Primero de todo, se realiza la habitual caracterización electroquímica in-situ con
voltametría cíclica, además de una caracterización física ex situ mediante TEM, para
obtener las formas predominantes en cada muestra de nanopartículas junto a su tamaño
promedio. Posteriormente, se realizan las voltametrías cíclicas para la oxidación de 0.2 M
CH3CH2OH + 0.1 M NaOH con las nanopartículas de platino de diferentes formas. Los
resultados concuerdan con los obtenidos en el capítulo 4 con superficies monocristalinas de
platino, siendo el orden de reactividad, determinado por la corriente de pico: (111)Pt >
(100-111)Pt > (100)Pt > (poly)Pt. Los dominios con orientación 111 son los que
presentan las mayores corrientes de oxidación, aunque el potencial de inicio de oxidación
de etanol se desplaza a potenciales más positivos. La explicación a esta elevada actividad
es la nula adsorción del anión acetato en medio alcalino, mientras que las diferencias en el
potencial de inicio de la oxidación entre las distintas muestras de nanopartículas de platino
se debe a que la adsorción del OH (necesaria para iniciar la oxidación de etanol) varía,
dependiendo de la orientación cristalográfica de la superficie de platino.
Las cronoamperometrías realizadas con estas mismas muestras tienen como objetivo
comprobar la estabilidad temporal del catalizador a un potencial de 0.6 V, donde la
Capítulo 5: Oxidación de etanol en nanopartículas de platino: efecto de la estructura superficial y de agregación de partículas
160
oxidación de etanol ha comenzado pero las corrientes no son demasiado grandes como
para tener dificultades en cuanto al transporte del etanol hacia la superficie del electrodo.
Las corrientes medidas también siguen la tendencia esperada según las voltametrías
cíclicas anteriores. La causa de la caída de corriente con el paso del tiempo se asocia con la
formación de acetaldehído y su posterior dimerización. De los experimentos de FTIR,
únicamente se puede corroborar la formación mayoritaria de acetato, independientemente
de la muestra de nanopartículas empleada. Además, se confirman los menores potenciales
necesarios para la aparición de las bandas en el caso de las muestras (100)Pt y (poly)Pt.
En cuanto al efecto de la aglomeración de nanopartículas, previo a su estudio en la
oxidación de etanol, la misma caracterización realizada anteriormente se efectuó en las
muestras de nanopartículas soportadas en carbón. La microscopía TEM muestra una mayor
dispersión de partículas en la muestra de Pt(10%) y mayores aglomerados en muestras
como la de Pt(50%), además de tamaños similares para todos los casos estudiados,
descartando problemas de sinterización durante el depósito de mayor cantidad de
nanopartículas. La caracterización electroquímica muestra picos de adsorción de hidrógeno
parecidos a los de una superficie de platino poliorientada. Al normalizar al área
electroactiva de platino, el aumento en la cantidad de Pt en las muestras provoca que la
contribución aparente de la doble capa propia del carbón vaya disminuyendo. La relación
lineal observada en el cociente entre las corrientes de pico debidos al platino y la de la
doble capa asociada al carbón vítreo frente a la cantidad de platino presente en la muestra
indica que todo el depósito de nanopartículas contribuye a la reacción electroquímica de
adsorción de hidrógeno, además de confirmar que el área de la carga de adsorción de
hidrógeno se puede utilizar para calcular el área activa del platino.
Posteriormente, se estudia el efecto de la aglomeración de estas nanopartículas
esféricas para la oxidación de etanol en medio alcalino. Conforme aumenta la cantidad de
Pt en las muestras, la densidad de corriente para la oxidación de etanol va decreciendo a
causa del difícil acceso de las moléculas de etanol hacia el depósito entero de
nanopartículas, siendo solamente activa la parte más externa del depósito de catalizador. Se
considera la oxidación de etanol sobre la muestra de Pt(10%) como la corriente que se
obtiene en ausencia de limitaciones de difusión, como se demuestra al comparar con un
electrodo de Pt poliorientado ciclado, ya que se obtienen corrientes parecidas. Con el
Resumen
161
propósito de evitar los problemas de aglomeración de nanopartículas de platino, se realiza
el secado del depósito de las nanopartículas mientras se rota el depósito de carbón vítreo a
una velocidad de 700 rpm. Con esto, es más uniforme la distribución de las partículas
después de la rotación del soporte de carbón vítreo. El resultado positivo sobre la
oxidación de etanol se demuestra en la Fig. 5.12: a bajos potenciales las densidades de
corriente siguen siendo similares mientras que a altos potenciales las densidades de
corriente son mayores cuando el depósito es uniforme, corroborando la mejora en la
actividad después de preparar el depósito secando a la vez que se rota el electrodo y su
mejor comportamiento para la electrooxidación de etanol.
163
Chapter 5
This chapter has been adapted and formatted from Journal of Solid State Electrochemistry 2016, 20, 1095-1106.
Corresponding authors: [email protected] and [email protected]
Chapter 5: Oxidation of ethanol on platinum nanoparticles: Surface structure and aggregation effects in alkaline medium
164
5.1 Introduction
Platinum is one on the most studied materials for its use as anode and/or cathode in
the fuel cell technology [1, 2]. Most of the electrochemical reactions occurring in fuel cells
are structure sensitive, that is, depending on the crystallographic orientation of the atoms
on the catalyst surface, the electrocatalytic activity changes. With the aim of understanding
this effect, platinum single crystal electrodes with a well-known surface structure are used
for fundamental studies of reactions with practical use in fuel cells [3-9]. However, single
crystal electrodes are not very useful from an applied point of view, and electrocatalysts
are usually presented in the form of nanoparticles. The effects of surface structure are still
important in nanoparticles, so it is necessary to control the atom arrangement on the
catalyst surface. With this aim, nanoparticles with different shapes, that is, with different
distribution of well-ordered crystallographic domains, have been synthesized. These
different nanoparticles have previously allowed extending the correlations between surface
structure and reactivity observed with single crystal electrodes for several reactions such as
the oxidations of formic acid, methanol, ethanol or ammonia [10-13] or the reduction of
oxygen [14]. Additionally, in some cases, the behavior of the nanoparticle electrodes
differs from that observed with single crystal electrodes [15, 16].
Among the molecules reacting in the anode of fuel cells, ethanol presents some
advantages: it is possible to be obtained directly from biomass, it is easy to store and it has
a higher energy density in the complete oxidation to CO2. In this reaction, 12 e- are
exchanged:
(5.1)
The thermodynamic standard potential is 0.085 V vs SHE, giving a standard
potential of 1.145 V for ethanol-oxygen fuel cell [17]. Nevertheless, the formation of many
undesired products and by-products due to its complex oxidation process, in addition to the
difficulty for breaking the C-C bond of ethanol at low temperatures, cause a decrease in the
efficiency of the ethanol fuel cell.
As observed for other fuels, ethanol oxidation is a structure sensitive reaction on
platinum electrodes [18]. The oxidation mechanism in acidic solutions has a dual-path
mechanism:
Introduction
165
(5.2)
Steps (1) and (2) correspond to the incomplete oxidation route to acetic acid. Step (1)
presents the formation of acetaldehyde, exchanging two electrons for this process, whereas
step (2) displays the final acetic acid formation with the exchange of two additional
electrons. Acetic acid is considered as a final product, because it is very difficult to oxidize
at room temperature [19]. Steps (3) and (4) represent the reaction steps that lead to the C-C
bond scission necessary for achieving the complete oxidation to CO2, forming one-carbon
fragments from ethanol or acetaldehyde [20, 21]. Behm’s group [22, 23] have proposed
acetyl species as the active intermediate for these CHx and one carbon oxygenated
fragments, which is quickly transformed in CO through the reaction step (5). CO is
strongly adsorbed on the Pt surface and hinders the electrocatalytic response of the
electrode. The final oxidation to CO2 is presented in the step (6). On Pt(111) electrodes,
only the incomplete oxidation to acetic acid is observed in acidic medium, whereas on
Pt(110) and, mainly, on Pt(100), the breakage of the C-C bond and, consequently, CO
formation is favored in the same medium [18]. The strategies to improve the
electrocatalysis of this reaction seek electrode materials that increase the rate of the C-C
bond cleavage and catalyze step (6) at lower potentials. Some alternatives for platinum are
the use of 110 stepped surfaces on 111 terraces [24] or the presence of foreign atoms
adsorbed on the Pt surface [25-29].
A change in the reactivity in the electrooxidation of small organic molecules such as
C1-C2 alcohols is normally observed in alkaline solutions showing higher activities than in
acidic solutions [30]. This fact, together with other advantages of the alkaline medium,
such as the lower corrosive properties (allowing the use of cheaper catalysts) [31], have
triggered fundamental studies in the electrocatalysis of these systems for alkaline fuel cells
(AFCs). However, there are mainly two problems when working at higher pH values: the
carbonation of the system due to the CO2 trapping and the necessity of finding membranes
capable of working in these pH values. Fortunately, new membranes have been developed
recently [32, 33] for overcoming this problem. Some positive results have been obtained
for the complete oxidation of ethanol working in alkaline solutions [34] with membrane
Chapter 5: Oxidation of ethanol on platinum nanoparticles: Surface structure and aggregation effects in alkaline medium
166
electrode assemblies (MEAs), obtaining efficiency values of 55% for CO2 at 60ºC,
improving the efficiency of 2% observed in the same conditions for acidic solutions.
Ethanol oxidation mechanism on platinum is also structure sensitive in alkaline
medium, but the ratio between the products is different from that in acid medium. A
previous work done by our group with single crystal electrodes using electrochemical and
FTIR techniques at room temperature [35] showed the preference for the acetate formation
independently of the surface structure of the electrodes. In this medium, CO2 formation
bands in FTIR were almost negligible and mainly related to pH changes in the thin layer
configuration. These results agree with infrared experiments done by Christensen et al.
with polycrystalline electrodes [36] or older results with single crystal electrodes [37].
However, Lai et al. proposed, according with Raman experiments, the adsorption of CO
and CHx species on 111 platinum sites during ethanol oxidation [38]. Finally, as in
acidic solutions, some studies try to achieve the complete oxidation in alkaline media by
adding foreign atoms adsorbed on the platinum surface, as for example, modifying Pt
single crystal electrodes with Pb [39].
On the other hand, and in addition to the surface structure effect, the dispersion of the
catalytic material on the supporting material is of paramount importance for the correct
evaluation of the electrocatalyst properties. Nanoparticle agglomeration causes different
effects on the studied reaction. A typical example of this is the CO electrooxidation
reaction on platinum nanoparticles [15, 40]. These studies have shown that peak
multiplicity and lower onset for CO oxidation are related to the nanoparticle
agglomeration. In the case of formic acid or ethanol oxidation reactions, studies with
different loadings of Pt nanoparticles supported on carbon in acidic medium show a
decrease in current densities when the Pt loading is increased [16], due to diffusional
problems of the reactant species in the platinum nanoparticle layer.
In the present manuscript, the effect of the surface structure/shape of platinum
nanoparticles for ethanol oxidation has been studied in alkaline solutions, trying to
establish a relationship with previous studies with Pt single crystal electrodes. In addition,
agglomeration effects have also been examined in this medium, to determine the role of
ethanol diffusion into the Pt nanoparticle catalyst layer by using disperse and non-disperse
Introduction
167
deposits. For both objectives, voltammetric and chronoamperometric techniques were used
for analyzing the reactivity of the Pt surfaces and spectroelectrochemical experiments were
carried out for determining the species adsorbed and formed during ethanol oxidation on
platinum nanoparticles.
Chapter 5: Oxidation of ethanol on platinum nanoparticles: Surface structure and aggregation effects in alkaline medium
168
5.2 Experimental
Four different Pt nanoparticle samples with different shapes were used. Polyoriented
nanoparticles, denoted as (poly)Pt, were synthesized with the water-in-oil microemulsion
method [41, 42] (water/polyethylene glycol dodecyl ether (Brij®30)/n-heptane) using 0.1
M H2PtCl6 as platinum precursor. Reduction was done directly by adding NaBH4 (ten
times the stoichiometric amount) to the micellar solution. After reduction, nanoparticles
were precipitated by adding NaOH, and then cleaned using acetone and ultrapure water. Pt
nanoparticles with preferential surface orientation were prepared using the colloidal
method [43, 44]. They present predominant 100, 111 and a mixture of 100 and
111 domains, denoted through the paper as (100)Pt, (111)Pt and (100-111)Pt
nanoparticles, respectively. For synthesizing them, 0.5 mL of 0.1 M sodium polyacrilate
solution (Mw = 2100) were added to 100 mL of an aged solution with the platinum
precursor (10-4 M), K2PtCl4 for (100)Pt nanoparticles and H2PtCl6 for (111)Pt and (100-
111)Pt nanoparticles. The ratio between the sodium polyacrilate and the Pt precursor was
5:1. The pH was adjusted to 7 with 0.1 M HCl for (100)-(111)Pt and (111)Pt nanoparticles,
whereas for the (100)Pt nanoparticles, pH was not adjusted. After that, the solutions were
deaerated with Ar for 20 min and Pt ions were reduced by bubbling H2 during 5 minutes,
except for the (111)Pt sample, which was purged for only 5 minutes whereas reduction
time with H2 was limited to 1 min. At this point, the reaction container was left overnight
for complete the reduction (12-14 h). After this, two NaOH pellets were added to induce
precipitation of nanoparticles. Finally, samples were cleaned three to four times with
ultrapure water.
To analyze possible diffusional problems of ethanol to the catalyst surface during
ethanol oxidation, polyoriented platinum nanoparticles supported on carbon were
synthesized using the citrate method [15, 45] with different metal loadings. In brief,
sodium citrate, which acts as stabilizer, and H2PtCl6 (the platinum precursor) were mixed
in the same concentration (2.5× 10-4 M) with ice-cold sodium borohydride, which is the
reducing agent. Once the platinum was reduced, carbon vulcan XC-72R was added under
stirring conditions. Magnetic and ultrasonic stirring was alternated for two hours with the
aim of dispersing the carbon in the water solution and favoring the adsorption of the
nanoparticles on the carbon surface. The different Pt loadings were obtained by varying the
Experimental
169
ratio between the amount of Pt and carbon vulcan. After the adsorption of nanoparticles on
carbon, two NaOH pellets were added to precipitate the catalysts overnight. Then, they
were washed and filtered with ultrapure water-NaOH four to five times. These Pt
nanoparticles supported on carbon are denoted as Pt(10%), Pt(20%), Pt(30%), Pt(40%) and
Pt(50%) depending on the Pt loading of the sample, and Pt(100%) for the unsupported Pt
nanoparticles.
For the studies with the preferentially oriented Pt nanoparticles, hemispherical
polycrystalline gold was used as a support (ca. 3 mm2) and the amount of nanoparticles
was adjusted so that the platinum active area was between 0.05-0.1 cm2, in order to avoid
transport problems of the reactant species to the catalyst surface. This effect is studied with
the nanoparticles supported in carbon. Therefore, for these nanoparticles, a fix amount of 4
µL was deposited on a commercial glassy carbon support with a 3 mm diameter. All the Pt
nanoparticles were cleaned using CO adsorption and stripping in 0.5 M H2SO4, following
the procedure of refs. [41, 46]. Before each experiment, a blank voltammogram was
recorded in 0.5 M H2SO4. The active area was calculated using the charge of the hydrogen
adsorption/desorption region after the apparent double layer subtraction, considering a
charge density of 0.23 mC cm-2 up to 0.6 V [47]. The upper potential limit in all the
voltammograms is set always below 0.95 V to assure the stability of the surface structure
of the nanoparticles. Additionally, a blank voltammogram is also recorded after the ethanol
oxidation experiments to verify that the nanoparticles samples have not suffered any
modification.
In situ FTIR spectra were acquired using a Nicolet (Model 8700) spectrometer,
equipped with a MCT (Mercury-Cadmium-Telluride) detector. The spectroelectrochemical
cell was coupled in a CaF2 window beveled at 60º as described previously [48]. The
spectra were obtained from the average of 100 interferograms with a resolution of 8 cm-1
using p-polarized light and are presented with absorbance units, A=-log[(R1-R2)/R1], where
R2 and R1 are the reflectance values corresponding to the single-beam spectra recorded at
the sample at any potential and at the reference potential, respectively. The reference
spectra were taken at 0.1 V, whereas the sample spectra were acquired doing different
steps between 0.1 V and 0.95 V vs. reversible hydrogen electrode (RHE). Positive bands
Chapter 5: Oxidation of ethanol on platinum nanoparticles: Surface structure and aggregation effects in alkaline medium
170
correspond to species that have increased their concentration with respect to the reference
potential and negative bands indicate species consumed.
The experiments were performed at room temperature conditions and in a three-
electrode electrochemical cell. A reversible hydrogen (N50, Air liquide) electrode was
used as a reference and a gold or platinum wire was used as a counter-electrode depending
on the support used (gold or glassy carbon respectively). Solutions were prepared with
NaOH (NaOH monohydrate 99.99%, Merck Suprapur), ethanol absolute (Merck p.a.) and
ultrapure water (Elga Purelab Ultra 18.2 MΩcm), whereas Ar (N50, Air Liquide) was used
for deoxygenating the solutions. The electrode potential was controlled with a µAutolab
type III. All the potentials presented in this paper are referred to the RHE. Finally, in order
to study the agglomeration effect, different drying procedures were evaluated. To perform
them, an EDI101 rotating disc electrode from Radiometer analytical with a commercial
glassy carbon tip (ca. 3 mm) was used.
Results and discussion
171
5.3 Results and discussion
5.3.1 Characterization of shape-controlled Pt nanoparticles
Fig. 5.1 shows some representative transmission electron microscopy (TEM) images
of the four preferentially oriented Pt nanoparticles samples studied in this work to evaluate
the surface structure effect of ethanol electrooxidation. As can be seen, each sample has
different shape and size characteristics that are summarized in Table 5.1. In this table, the
predominant are ordered domains on the surface are also given.
Fig. 5.1. TEM pictures for: a) (poly)Pt, b) (100)Pt, c) (100-111)Pt and d) (111)Pt nanoparticles.
Average size/nm
Preferential shape Preferential ordered domains
(poly)Pt 4.0 ± 0.6 Sphere none
(100)Pt 8.2 ± 1.6 Cube (100)
(100-111)Pt 11.5 ± 1.7 Truncated cube (100) & (111)
(111)Pt 8.6 ± 1.4 Octahedron (111)
Table 5.1. Physical characteristics of the preferentially ordered nanoparticles used in the work.
Chapter 5: Oxidation of ethanol on platinum nanoparticles: Surface structure and aggregation effects in alkaline medium
172
In addition to the TEM images of the nanoparticles, a voltammetric characterization
is needed to corroborate the presence of the ordered Pt domains suggested with the TEM
images. The voltammetric profile of a Pt sample in H2SO4 can be considered as a
fingerprint of its surface structure, which allows assessing the type and ratio of the
different domains present on the surface [46]. Fig. 5.2 displays the voltammograms
obtained in 0.5 M H2SO4, highlighting the hydrogen adsorption region for the four samples
studied.
Fig. 5.2. Voltammetric profiles in 0.5 M H2SO4 for the different nanoparticle samples. Scan rate: 0.05
Vs-1.
The (poly)Pt nanoparticles present the typical features of a polyoriented platinum
electrode, with two main peaks at 0.125 and 0.265 V. The peak at 0.125 V is assigned to
110 sites, whereas the peak at 0.265 V corresponds to 100 defects on 111 domains
or 100 short domains. In the other samples, characteristic peaks for ordered domains can
be observed in addition to those present in a polyoriented sample. The (100)Pt
nanoparticles present a peak at 0.370 V, related to the presence of long-range 100
ordered domains. This peak is also observed in the (100-111)Pt nanoparticles in addition to
the wide signal around 0.500 V assigned to sulfate adsorption on 111 ordered domains.
This latter signal is very prominent for the (100-111) and especially for the (111)Pt
nanoparticles sample. The voltammetric profile of these samples is perfectly symmetrical,
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.70.00
0.02
0.04
0.06
0.08
0.10
0.12
j/mA
cm-2
E/V vs. RHE
(poly)Pt (100)Pt (100-111)Pt (111)Pt
Results and discussion
173
corroborating the cleanliness of the surface of the nanoparticle and the success in the
removal of the chemicals used during the synthesis. A more detailed study of the
voltammetric profiles depending on the different preferential surface structure of the
nanoparticles and the electrolyte has been previously published by our group [46, 47, 49].
5.3.2 Ethanol oxidation on preferentially shaped Pt nanoparticles
Ethanol oxidation experiments were carried out with the preferentially oriented Pt
nanoparticles in alkaline medium (Fig. 5.3) to study the surface structure effect and to
establish correlations with previous results with single crystal electrodes [35]. In addition,
the behavior could be compared with that of the same Pt nanoparticles in acidic solutions
[12]. In all the experiments, the upper potential limit was set to 0.95 V to avoid changes on
the surface structure of the Pt nanoparticles due to oxide formation. The first cycle is
presented in all the figures because a large deactivation process is observed in this medium
upon cycling.
Fig. 5.3. Ethanol oxidation (1st cycle): a) (poly)Pt, b) (100)Pt, c) (100-111)Pt and d) (111)Pt
nanoparticles. Test solution: 0.2 M CH3CH2OH + 0.1 M NaOH. Sweep rate: 0.02 Vs-1.
0
5
10
15
20
25
30
0.0 0.2 0.4 0.6 0.8 0.2 0.4 0.6 0.8 1.0
0
5
10
15
20
25
30
0.0 0.2 0.4 0.6 0.80
5
10
15
20
25
30
0.2 0.4 0.6 0.8 1.00
5
10
15
20
25
30d)c)
b)j/m
A cm
-2j/m
A cm
-2
j/mA
cm-2
a)
E vs. RHE/VE vs. RHE/V
j/mA
cm-2
E vs. RHE/V
E vs. RHE/V
Chapter 5: Oxidation of ethanol on platinum nanoparticles: Surface structure and aggregation effects in alkaline medium
174
The voltammetric profiles shown in Fig. 5.3 clearly illustrate the surface structure
effect observed for this reaction in alkaline medium, and follow the same trends observed
with single crystal electrodes [35]. Among the Pt basal planes, it is the Pt(111) electrode
that exhibits the highest peak current density and also the highest onset potential. Thus, the
nanoparticle sample with long range 111 domains, namely (111)Pt and (100-111)Pt
nanoparticles, present higher currents and a higher onset potential, whereas the (100)Pt and
(poly)Pt nanoparticles show a lower onset potential. The maximum activity (maximum
peak current density) for the four prepared samples follows the expected order obtained
from the reactivity of single crystal electrodes [35], that is, (111)Pt > (100-111)Pt >
(100)Pt > (poly)Pt. On the other hand, the onset potential is associated with the adsorption
of OH on the Pt surface, because it has been proposed that, in alkaline solutions, these
species provides the oxygen group necessary for the oxidation of ethanol, in a different
way to that taking place in acidic solutions, where water molecules act as the oxygen donor
to the ethanol molecule. Thus, the OH adsorption is the key for triggering the ethanol
oxidation, offering a lower onset potential in surfaces with 100 domains, as OH
adsorption occurs at potentials more negative than those observed for the 111 domains
[50].
When compared with the results obtained in acidic solutions, the voltammetric
profile in alkaline medium is significantly different, showing higher currents and lower
hysteresis, independently of the Pt nanoparticles sample used. In acidic conditions, anion
adsorption plays a significant role in the process, since specific adsorption of anions hinder
ethanol oxidation, giving rise to lower currents. In perchloric acid solutions, the adsorption
of acetate coming from the acetic acid formed during the oxidation adsorbs strongly on the
electrode surface and inhibits the oxidation [18]. When sulfuric acid solutions are
employed, adsorbed sulfate is detected in the potential window where ethanol oxidation
takes place. However, in alkaline medium, the absolute potential is more negative and
acetate (or any other anion) adsorption does not take place, favoring the ethanol oxidation.
This fact explains the high activity for platinum electrodes in alkaline solutions, especially
in 111 domains, the most active electrode for acetate formation comparing with the other
basal planes, as is also observed in perchloric acid solutions with the currents at very short
times prior to the adsorption of acetate [18].
Results and discussion
175
Regarding the different hysteresis observed depending on the nanoparticle sample
used, this phenomenon is normally related in acidic pH values to the CO formation at low
potentials and its posterior oxidation at potentials above 0.5-0.6 V. According with the low
hysteresis observed in Fig. 5.3 and using previous results with Pt single crystal and Pt
polyoriented electrodes [35, 36, 38], a change in the oxidation mechanism is proposed,
with a low CO formation rate at low potentials and acetate formation as the main product
of the oxidation. Another important difference for ethanol oxidation on Pt nanoparticles in
alkaline solutions observed also in Pt single crystal electrodes [35] is the huge deactivation
of the Pt surface (not shown) when the electrode is cycled several times, especially when
111 domains are present at the surface. This deactivation is due to acetaldehyde
formation, the previous step before acetate formation. Acetaldehyde can dimerize and
produce inhibiting species that adsorb on the surface through CHx groups [38] and cause
the deactivation.
In order to gain insight into the stability of the electrocatalytic process at low
potentials and the importance of this deactivation process, chronoamperometric currents
were recorded at 0.6 V. This potential was selected because ethanol oxidation has already
started but currents are not very high so that there are no transport limitations of ethanol to
the electrode surface.
Fig. 5.4. Current transients recorded at 0.6 V for ethanol oxidation on the different Pt nanoparticles.
Test solution: 0.2 M CH3CH2OH + 0.1 M NaOH.
0 200 400 600 800 10000
1
2
3
4
5
j/mA
cm-2
t/s
(poly)Pt (100)Pt (100-111)Pt (111)Pt
Chapter 5: Oxidation of ethanol on platinum nanoparticles: Surface structure and aggregation effects in alkaline medium
176
Fig. 5.4 shows the transient currents registered for 15 min after two successive steps:
first from 0.1 V to 0.9 V, for removing the possible poison species formed at lower
potentials during 5 s, and then to 0.6 V for recording the transient. The measured currents
follow the trend observed for the currents recorded in the voltammetric profile of Fig. 5.3
at 0.6 V, displaying the largest current for the (100)Pt nanoparticles, and lower activities
for the nanoparticles with a larger amount of 111 domains, (100-111)Pt and (111)Pt
nanoparticles.
Nevertheless, in similar experiments performed for single crystal electrodes in acidic
medium [18], currents of the three platinum basal planes decay much faster at 0.6 V due to
CO formed which poisons the surface in the case of Pt(100) and Pt(110) and to adsorbed
anions as acetate or sulfate for Pt(111). However, in alkaline solutions, the effect of acetate
adsorption can be discarded due to the displacement of the absolute potential towards
negative values, and CO formation is negligible, suggesting that the differences in the
transient currents come from the adsorption of the acetaldehyde and its polymerization
[35]. In connection with this, a slight reactivation is observed at short times for all samples
except for (111)Pt nanoparticles sample at 0.6 V. This feature is assigned to 100
domains [35], promoting a current increase due to the OH adsorption at the beginning of
the transient measurements. At 0.6 V, OH adsorption occurs on these domains and favors
the ethanol oxidation until the formation of the species coming from acetaldehyde, which
inhibits the platinum surface.
5.3.3 FTIR experiments for ethanol oxidation
Fig. 5.5 and Fig. 5.6 show the FTIR experiments carried out with the four
preferentially oriented Pt nanoparticles with the aim of finding out the species adsorbed or
produced during ethanol oxidation. The spectra obtained are very similar to those obtained
for single crystal electrodes [35], with two main bands at 1550 and 1415 cm-1 assigned to
the O-C-O asymmetrical and symmetrical vibrational modes of acetate respectively,
according to previous works [36, 51]. Acetate bands appear at around 0.3 V for the (100)Pt
and 0.4 V for (poly)Pt nanoparticles, which are lower potentials in comparison with the
Results and discussion
177
(111)Pt and (100-111)Pt nanoparticles, where the bands appear at 0.5 V, although small
signals are observed for (111)Pt at 0.4 V. These data are in agreement with the onset
potentials for ethanol oxidation, as it is shown in the voltammetric profiles of Fig. 5.3, that
is, ethanol oxidation starts at lower potentials for (100)Pt and (poly)Pt nanoparticles.
Fig. 5.5. In situ FTIR spectra for ethanol oxidation on a) (poly)Pt and b) (100)Pt nanoparticles, using
spectra at 0.1 V as a reference. Test solution: 0.2 M CH3CH2OH + 0.1 M NaOH.
Additionally, a poor affinity of the nanoparticles for the C-C bond scission for
ethanol oxidation at higher pHs is observed, with very weak bands of adsorbed CO at
around 2030 cm-1 detected at low potentials [35] independently of the preferential surface
structure of the Pt nanoparticles. These very weak bands support the proposed change in
the oxidation mechanism with respect to acidic medium. The appearance of small CO2
bands at 2340 cm-1, atypical at these higher pHs, suggests a large shift in the interfacial pH,
due to the depletion of the OH- in the thin layer during ethanol oxidation [52, 53]. In this
2400 2200 2000 1800 1600 1400 1200
b)
0.95 V0.9 V0.85 V0.8 V0.7 V0.6 V0.5 V0.4 V0.3 V
0.2 V
0.01 a.u.a)
υ/cm-1
0.95 V0.9 V0.85 V0.8 V0.7 V0.6 V0.5 V0.4 V0.3 V
0.2 V
0.01 a.u.
Chapter 5: Oxidation of ethanol on platinum nanoparticles: Surface structure and aggregation effects in alkaline medium
178
sense, the presence of carbonate cannot be discarded, which shows a main band at 1390
cm-1, which overlaps with the acetate bands. However, according to the negligible CO
adsorption band, it can be confirmed that the main product in the ethanol oxidation is the
incomplete oxidation to acetate in the same way that it is observed for the single crystal
electrodes.
Fig. 5.6. In situ FTIR spectra for ethanol oxidation on a) (100-111)Pt and b) (111)Pt nanoparticles
using spectra at 0.1 V as a reference. Test solution: 0.2 M CH3CH2OH + 0.1 M NaOH.
5.3.4 Characterization of Pt nanoparticles supported on carbon
To further characterize the behavior of Pt nanoparticles in alkaline solution and
demonstrate the importance of a good dispersion of the catalyst in the reactive layer,
additional experiments were carried out with polyoriented nanoparticles supported on
carbon with different metal loadings. Fig. 5.7 displays the TEM images for these Pt
samples. As can be seen, the degree of agglomeration increases with the metal loading. For
the Pt(10%) sample, isolated nanoparticles can be distinguished throughout the carbon
2400 2200 2000 1800 1600 1400 1200
b)
0.95 V0.9 V0.85 V0.8 V0.7 V0.6 V0.5 V0.4 V0.3 V
0.2 V
0.01 a.u.a)
υ/cm-1
0.95 V0.9 V0.85 V0.8 V0.7 V0.6 V0.5 V0.4 V0.3 V
0.2 V
0.01 a.u.
Results and discussion
179
support, whereas large agglomerates can be observed for the Pt(50%) sample.
Nevertheless, it is important to highlight that the different samples are made with the same
synthesis method and the average size of the nanoparticles is practically the same for all
the samples (between 2.1 and 2.4 nm), implying that the individual nanoparticles are the
same in all the samples, and discarding any sintering process during the deposition of the
nanoparticles on the carbon support to produce larger nanoparticles.
Fig. 5.7. TEM pictures for a) Pt(10%), b) Pt(20%), c) Pt(30%), d) Pt(40%) and e) Pt(50%)
nanoparticles supported on carbon and f) Pt(100%), the unsupported Pt nanoparticles.
Following the same procedure observed in Fig. 5.2 for the electrochemical
characterization in 0.5 M H2SO4, Fig. 5.8 presents the results of the voltammetric profiles
for the Pt nanoparticles supported on carbon performed in the same electrolyte. Similarly
to the (poly)Pt nanoparticles of Fig. 5.2 (black line), all the carbon-supported samples
present the characteristic peaks in the hydrogen adsorption/desorption region of a
polyoriented surface without showing signals coming from large 111 or 100 ordered
Chapter 5: Oxidation of ethanol on platinum nanoparticles: Surface structure and aggregation effects in alkaline medium
180
domains, which are absent on these small nanoparticles. The symmetry and sharpness of
the hydrogen adsorption/desorption contributions prove the cleanliness of the surface. In
addition, when the voltammetric profiles are normalized to the platinum electroactive area,
the double layer contribution of the carbon in the voltammogram diminishes, leading to
lower current densities in the so-called double layer region of Pt.
Fig. 5.8. Voltammetric profile for: a) Pt(10%), b) Pt(20%), c) Pt(30%), d) Pt(40%), e) Pt(50%) and f)
Pt(100%) nanoparticles. Test solution: 0.5 M H2SO4. Scan rate: 0.05 V s-1.
In order to confirm that the agglomeration observed by TEM in the samples with a
high platinum loading does not affect their electrochemical activity, that is to say, that the
whole sample is contributing to the electrochemical signal registered in the
voltammograms, the ratio of the currents for hydrogen adsorption and for double layer was
analyzed for the different samples. Fig. 5.9 shows the ratio between the currents at 0.12 V,
which contains contributions from the platinum and carbon, and 0.42 V, where the current
mainly comprises double-layer contributions from carbon. As can be seen, a clear linear
dependence is observed, ensuring that the surface area of platinum is directly proportional
to the total amount of platinum. In addition, the intercept of the linear fit is 1, which
corroborates that the major contribution for the current at 0.42 V is the double layer current
-0.15
-0.10
-0.05
0.00
0.05
0.10
0.15
0.0 0.2 0.4 0.6 0.8 0.2 0.4 0.6 0.8 0.2 0.4 0.6 0.8
-0.15
-0.10
-0.05
0.00
0.05
0.10
0.15
0.0 0.2 0.4 0.6 0.8
-0.15
-0.10
-0.05
0.00
0.05
0.10
0.15
0.2 0.4 0.6 0.8 0.2 0.4 0.6 0.8
-0.15
-0.10
-0.05
0.00
0.05
0.10
0.15e)d) f)
b)a)
j/mA
cm-2
j/mA
cm-2
c)
j/mA
cm-2
E/V vs. RHE
j/mA
cm-2
E/V vs. RHE
E/V vs. RHE
E/V vs. RHE
E/V vs. RHE
E/V vs. RHE
Results and discussion
181
from the carbon support. Thus, from the results show in Fig. 5.9, it can be confirmed that
the entire surface of the platinum nanoparticles is available for the hydrogen adsorption-
desorption process.
Fig. 5.9. Ratio between current densities at 0.12 V and 0.42 V vs Pt loading of the nanoparticle
samples supported on carbon.
5.3.5 Aggregation effect in ethanol oxidation
The behavior for ethanol oxidation in alkaline medium was studied for these Pt
samples. Fig. 5.10 shows the results using the same potential window and conditions as in
Fig. 5.3. In spite of the different sizes and the presence of the vulcan support, the
voltammetric shape and peak currents are the same as those recorded in Fig. 5.3 for the
(poly)Pt nanoparticle sample, indicating that no significant size effects are observed for
this reaction for polyoriented Pt nanoparticles. Additionally, as the platinum loading
increases in the sample, current densities diminish. To calculate these current densities, the
hydrogen adsorption charge has been used, because Fig. 5.9 indicates that the whole
surface area is electrochemically active. However, the diminution of the current densities
with the Pt loading indicates that the whole Pt surface area is not active in the same extent
for ethanol oxidation. This diminution should be related to the increasing diffusional
0 10 20 30 40 50 600
1
2
3
4
5
6
7
j 0.12
V/j 0.
42 V
% Pt
R2 = 0.98171
Chapter 5: Oxidation of ethanol on platinum nanoparticles: Surface structure and aggregation effects in alkaline medium
182
problems of ethanol as the loading becomes higher, as happened also in sulfuric and
perchloric acid solutions [16]. Surely, the most external part of the nanoparticle deposit is
always contributing to the ethanol oxidation. However, the inner parts of this deposit for
high loadings are not contributing in the same way because all the ethanol flux coming
from the bulk solution is mainly consumed in the outer part of the layer.
Fig. 5.10. Voltammetric profiles (1st cycle) in 0.2 M CH3CH2OH + 0.1 M NaOH for Pt nanoparticles
supported on carbon with different metal loadings and for a cycled Pt poly electrode. Sweep rate: 0.02 V s-1.
Thus, an apparent decrease in the activity is observed when the Pt loading increases
due to diffusional problems of ethanol through the catalyst layer. It could be consider that
the 10% loading represents the currents that could be obtained in absence of diffusional
problems. To prove that, the voltammetric response of a bulk Pt electrode that has been
previously cycled in the oxide region to remove all the 111 and 100 ordered domains
[46], has been also incorporated in Fig. 5.10. This voltammogram represents the response
of a typical polycrystalline Pt electrode with no preferential orientation in the same
experimental conditions used in the nanoparticle tests. Due to the large limiting diffusion
current that could be obtained for ethanol oxidation if the electrode kinetics for the reaction
were fast (ca. 100 mA/cm2 for the employed concentration), the measured currents for the
bulk electrode are not affected by diffusion of ethanol and represent the intrinsic activity of
the bulk Pt for the reaction. The measured currents for the Pt(10%) are slightly higher than
0.0 0.2 0.4 0.6 0.8 1.0
0
2
4
6
8
10
j/mA
cm-2
E vs. RHE/V
Pt(10%) Pt(20%) Pt(30%) Pt(40%) Pt(50%) Pt(100%) Pt(poly)
Results and discussion
183
those for the Pt(poly), probably related to a small effect of the particular surface structure
of the nanoparticles. Thus, these currents represent the behavior of the nanoparticles in
absence of ethanol diffusion limitations.
From the results shown in Fig. 5.10, it can be said that the dispersion of Pt
nanoparticles on the carbon support is the key parameter for obtaining the true activity of
the nanoparticles. With the aim of avoiding the agglomeration of nanoparticles and
improving the quality of the deposit with better dispersion of the nanoparticles, Garsany
and co-workers [54-56] proposed a different procedure for preparing the Pt nanoparticle
deposit that gives reproducible Pt thin films with an increase in activity for the oxygen
reduction reaction. This method uses a RDE glassy carbon tip rotating at 700 rpm as
support for the deposit of the different samples of nanoparticles. The same procedure to
prepare the nanoparticles deposit was used here, using a commercial glassy carbon tip of a
RDE, which was rotated at 700 rpm while the solution containing the supported
nanoparticles was dried with Ar.
As expected, the dispersion of the layer is significantly improved when rotating
conditions are used during the drying step. Fig. 5.11 shows the effect of the rotation in the
dispersion of the catalyst layer. For improving the image contrast, a gold support was used
instead of a glassy carbon. As can be seen from the optical microscope images, the deposit
obtained with rotation (Fig. 5.11b) shows a uniform dispersion of the catalyst layer.
However, in the normal deposit, that obtained without rotation (Fig. 5.11a), the deposit is
non-uniform and a large fraction of the gold support is still visible.
Fig. 5.11. Images of the Pt(40%) nanoparticles deposited on a gold support for a: a) non-rotating and
b) rotating support (700 rpm) during the drying procedure.
Chapter 5: Oxidation of ethanol on platinum nanoparticles: Surface structure and aggregation effects in alkaline medium
184
The electrochemical response of two Pt(40%) nanoparticle layers prepared with and
without rotation is shown in Fig. 5.12.
Fig. 5.12. Voltammetric profile (1st cycle) for ethanol oxidation for Pt(40%) nanoparticles supported
on carbon with a static (black line) and rotating (red line) glassy carbon support (700 rpm) during the drying
deposit procedure. Test solution: 0.2 M CH3CH2OH + 0.1 M NaOH. Sweep rate: 0.02 V s-1. IR drop has been
corrected.
A significant increase in the activity for the sample prepared using rotation is
observed, which highlights the dependence of the electrocatalytic response with the film
morphology. Comparing the measured currents for both experiments, it can be seen that
the voltammograms almost overlap in the regions where small currents are recorded. In
this current region, the only difference between both samples is a small displacement of the
onset potential to lower values for the more dispersed sample, which can be related to
some minor effect in the local conditions that affect the onset potential in agglomerated
samples [15]. The almost constant currents in the low current regime is a clear indication
that for those currents there are no diffusional problems, and the whole nanoparticles’
surface is contributing in the same way to the ethanol electrooxidation. In the region where
high current densities are obtained, larger currents are also recorded for the uniform
deposit, corroborating its better performance for the ethanol electrooxidation.
0.0 0.2 0.4 0.6 0.8 1.0
0
1
2
3
4
5
j/mA
cm-2
E vs. RHE/V
Conclusions
185
5.4 Conclusions
The results presented here highlight the importance of controlling two parameters in
the platinum electrocatalysts for ethanol oxidation in alkaline solutions: the surface
structure and the dispersion of the nanoparticle electrocatalysts. The solution pH also
affects the reactivity of ethanol in platinum, showing an increasing in the total activity
when it becomes more alkaline and a change in potential range where the reaction occurs.
For this purpose, two types of samples were used. For studying the surface structure effect,
shape-controlled platinum nanoparticles were employed, whereas the effect of the
dispersion of the catalyst was studied with different loadings of polyoriented nanoparticles
supported on carbon.
Shape-controlled nanoparticles, namely, (poly)Pt, (100)Pt, (111)Pt and (100-111)Pt
nanoparticles, were tested for ethanol oxidation in alkaline solution using electrochemical
and IR techniques. The experiments show the preference for acetate formation
independently of the preferential shape of the Pt nanoparticles, while the amount of CO2
formed is always negligible. Additionally, (100) and (poly)Pt nanoparticles show lower
currents and a lower onset than the nanoparticles that have a significant fraction of 111
ordered domains. The differences in the reactivity have been ascribed to the different OH
adsorption potential of the different domains present on the surface.
The use of the polyoriented Pt nanoparticles supported on carbon has demonstrated
that the dispersion of the catalyst is important for the optimum performance of the deposit.
Lower activities have been reported in the case of more agglomerated and non-uniform
deposits. With the aim of increasing the uniformity of the catalyst film, a previously
reported methodology was used [54-56]. With this method the dispersion containing the
nanoparticles was dried while the electrode was rotated at 700 rpm for improving the
dispersion of the catalyst. A higher catalytic activity was obtained for the films obtained
using this procedure, stressing the importance of the dispersion of the catalyst on the
support for better performances.
Chapter 5: Oxidation of ethanol on platinum nanoparticles: Surface structure and aggregation effects in alkaline medium
186
5.5 References
[1] M. T. M. Koper, ''Fuel Cell Catalysis: A Surface Science Approach'', Electrocatalysis and Electrochemistry A. Wieckowski (Ed.), John Wiley & Sons, Hoboken, New Jersey, 2009.
[2] R. Parsons and T. VanderNoot, ''The oxidation of small organic molecules: A survey of recent fuel cell related research'' Journal of Electroanalytical Chemistry 1988, 257, 9-45.
[3] C. Lamy and J. M. Léger, ''Electrocatalytic oxidation of small organic molecules at platinum single crystals'' Journal de Chimie Physique et de Physico-Chimie Biologique 1991, 88, 1649-1671.
[4] J. M. Feliu and E. Herrero, ''Formic acid oxidation'', in Handbook of Fuel Cells - Fundamentals, Technology and Applications, vol. 2, W. Vielstich, H. Gasteiger and A. Lamm (Eds.) Wiley, Chichester, 2003, pp. 625-634.
[5] T. Iwasita, ''Electrocatalysis of methanol oxidation'' Electrochimica Acta 2002, 47, 3663-3674.
[6] J. M. Orts, A. Fernández-Vega, J. M. Feliu, A. Aldaz and J. Clavilier, ''Electrochemical Oxidation of Ethylene-Glycol on Pt Single-Crystal Electrodes with Basal Orientations in Acidic Medium'' Journal of Electroanalytical Chemistry 1990, 290, 119-133.
[7] N. M. Markovic, H. A. Gasteiger and P. N. Ross, ''Oxygen Reduction on Platinum Low-Index Single-Crystal Surfaces in Sulfuric-Acid-Solution - Rotating Ring-Pt(Hkl) Disk Studies'' Journal of Physical Chemistry 1995, 99, 3411-3415.
[8] A. Kuzume, E. Herrero and J. M. Feliu, ''Oxygen reduction on stepped platinum surfaces in acidic media'' Journal of Electroanalytical Chemistry 2007, 599, 333-343.
[9] R. Rizo, E. Herrero and J. M. Feliu, ''Oxygen reduction reaction on stepped platinum surfaces in alkaline media'' Physical Chemistry Chemical Physics 2013, 15, 15416-15425.
[10] J. Solla-Gullón, F. J. Vidal-Iglesias, A. López-Cudero, E. Garnier, J. M. Feliu and A. Aldaz, ''Shape-dependent electrocatalysis: methanol and formic acid electrooxidation on preferentially oriented Pt nanoparticles'' Physical Chemistry Chemical Physics 2008, 10, 3689-3698.
[11] V. Grozovski, J. Solla-Gullón, V. Climent, E. Herrero and J. M. Feliu, ''Formic Acid Oxidation on Shape-Controlled Pt Nanoparticles Studied by Pulsed Voltammetry'' Journal of Physical Chemistry C 2010, 114, 13802-13812.
[12] C. Busó-Rogero, V. Grozovski, F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero and J. M. Feliu, ''Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles'' Journal of Materials Chemistry A 2013, 1, 7068-7076.
[13] F. J. Vidal-Iglesias, J. Solla-Gullón, P. Rodríguez, E. Herrero, V. Montiel, J. M. Feliu and A. Aldaz, ''Shape-dependent electrocatalysis: ammonia oxidation on platinum nanoparticles with preferential (100) surfaces'' Electrochemistry Communications 2004, 6, 1080-1084.
[14] J. Hernández, J. Solla-Gullón, E. Herrero, A. Aldaz and J. M. Feliu, ''Electrochemistry of shape-controlled catalysts: Oxygen reduction reaction on cubic gold nanoparticles'' Journal of Physical Chemistry C 2007, 111, 14078-14083.
[15] A. López-Cudero, J. Solla-Gullón, E. Herrero, A. Aldaz and J. M. Feliu, ''CO electrooxidation on carbon supported platinum nanoparticles: Effect of aggregation'' Journal of Electroanalytical Chemistry 2010, 644, 117-126.
[16] S. Chumillas, C. Busó-Rogero, J. Solla-Gullón, F. J. Vidal-Iglesias, E. Herrero and J. M. Feliu, ''Size and diffusion effects on the oxidation of formic acid and ethanol on platinum nanoparticles'' Electrochemistry Communications 2011, 13, 1194-1197.
[17] C. Lamy and C. Coutanceau, ''Electrocatalysis of Alcohol Oxidation Reactions at Platinum Group Metals'', in Catalysts for Alcohol-Fuelled Direct Oxidation Fuel Cells, vol. 6, Z.-X. Liang and T. S. Zhao (Eds.) RSC Energy and Enviroment Series 2012.
[18] F. Colmati, G. Tremiliosi-Filho, E. R. Gonzalez, A. Berná, E. Herrero and J. M. Feliu, ''Surface structure effects on the electrochemical oxidation of ethanol on platinum single crystal electrodes'' Faraday Discussions 2008, 140, 379-397.
References
187
[19] A. Rodes, E. Pastor and T. Iwasita, ''An FTIR Study on the Adsorption of Acetate at the Basal Planes of Platinum Single-Crystal Electrodes'' Journal of Electroanalytical Chemistry 1994, 376, 109-118.
[20] T. Iwasita and E. Pastor, ''A DEMS and FTIR spectroscopic investigation of adsorbed ethanol on polycrystalline platinum'' Electrochimica Acta 1994, 39, 531-537.
[21] U. Schmiemann, U. Müller and H. Baltruschat, ''The Influence of the Surface-Structure on the Adsorption of Ethene, Ethanol and Cyclohexene as Studied by DEMS'' Electrochimica Acta 1995, 40, 99-107.
[22] H. Wang, Z. Jusys and R. J. Behm, ''Ethanol electrooxidation on a carbon-supported Pt catalyst: Reaction kinetics and product yields'' Journal of Physical Chemistry B 2004, 108, 19413-19424.
[23] M. Heinen, Z. Jusys and R. J. Behm, ''Ethanol, Acetaldehyde and Acetic Acid Adsorption/Electrooxidation on a Pt Thin Film Electrode under Continuous Electrolyte Flow: An in Situ ATR-FTIRS Flow Cell Study'' Journal of Physical Chemistry C 2010, 114, 9850-9864.
[24] F. Colmati, G. Tremiliosi-Filho, E. R. Gonzalez, A. Berná, E. Herrero and J. M. Feliu, ''The role of the steps in the cleavage of the C-C bond during ethanol oxidation on platinum electrodes'' Physical Chemistry Chemical Physics 2009, 11, 9114-9123.
[25] V. Del Colle, A. Berná, G. Tremiliosi-Filho, E. Herrero and J. M. Feliu, ''Ethanol electrooxidation onto stepped surfaces modified by Ru deposition: electrochemical and spectroscopic studies'' Physical Chemistry Chemical Physics 2008, 10, 3766-3773.
[26] V. Del Colle, V. Santos and G. Tremiliosi-Filho, ''Comparative Electrochemical and Spectroscopic Studies of Ethanol Oxidation on Pt(h,k,l) Modified by Osmium Nanoislands'' Electrocatalysis 2010, 1, 144-158.
[27] V. Del Colle, J. Souza-Garcia, G. Tremiliosi-Filho, E. Herrero and J. M. Feliu, ''Electrochemical and spectroscopic studies of ethanol oxidation on Pt stepped surfaces modified by tin adatoms'' Physical Chemistry Chemical Physics 2011, 13, 12163-12172.
[28] J. Souza-Garcia, E. Herrero and J. M. Feliu, ''Breaking the C-C Bond in the Ethanol Oxidation Reaction on Platinum Electrodes: Effect of Steps and Ruthenium Adatoms'' ChemPhysChem 2010, 11, 1391-1394.
[29] G. A. B. Mello, M. J. S. Farias, M. J. Giz and G. A. Camara, ''Oxidation of isotopically-labeled ethanol on platinum-tin-rhodium surfaces: Enhancing the production of CO2 from methyl groups'' Electrochemistry Communications 2014, 48, 160-163.
[30] A. V. Tripkovic, K. D. Popovic and J. D. Lovic, ''The influence of the oxygen-containing species on the electrooxidation of the C1-C4 alcohols at some platinum single crystal surfaces in alkaline solution'' Electrochimica Acta 2001, 46, 3163-3173.
[31] E. Antolini and E. R. Gonzalez, ''Alkaline direct alcohol fuel cells'' Journal of Power Sources 2010, 195, 3431-3450.
[32] J. S. Spendelow and A. Wieckowski, ''Electrocatalysis of oxygen reduction and small alcohol oxidation in alkaline media'' Physical Chemistry Chemical Physics 2007, 9, 2654-2675.
[33] C. Coutanceau, L. Demarconnay, C. Lamy and J. M. Léger, ''Development of electrocatalysts for solid alkaline fuel cell (SAFC)'' Journal of Power Sources 2006, 156, 14-19.
[34] V. Rao, Hariyanto, C. Cremers and U. Stimming, ''Investigation of the ethanol electro-oxidation in alkaline membrane electrode assembly by differential electrochemical mass spectrometry'' Fuel Cells 2007, 7, 417-423.
[35] C. Busó-Rogero, E. Herrero and J. M. Feliu, ''Ethanol Oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium'' ChemPhysChem 2014, 15, 2019-2028.
[36] P. A. Christensen, S. W. M. Jones and A. Hamnett, ''In Situ FTIR Studies of Ethanol Oxidation at Polycrystalline Pt in Alkaline Solution'' Journal of Physical Chemistry C 2012, 116, 24681-24689.
[37] M. López-Atalaya, E. Morallón, F. Cases, J. L. Vázquez and J. M. Pérez, ''Electrochemical oxidation of ethanol on Pt(hkl) basal surfaces in NaOH and Na2CO3 media'' Journal of Power Sources 1994, 52, 109-117.
Chapter 5: Oxidation of ethanol on platinum nanoparticles: Surface structure and aggregation effects in alkaline medium
188
[38] S. C. S. Lai and M. T. M. Koper, ''Ethanol electro-oxidation on platinum in alkaline media'' Physical Chemistry Chemical Physics 2009, 11, 10446-10456.
[39] P. A. Christensen, S. W. M. Jones and A. Hamnett, ''An in situ FTIR spectroscopic study of the electrochemical oxidation of ethanol at a Pb-modified polycrystalline Pt electrode immersed in aqueous KOH'' Physical Chemistry Chemical Physics 2013, 15, 17268-17276.
[40] O. V. Cherstiouk, P. A. Simonov, V. I. Zaikovskii and E. R. Savinova, ''CO monolayer oxidation at Pt nanoparticles supported on glassy carbon electrodes'' Journal of Electroanalytical Chemistry 2003, 554, 241-251.
[41] J. Solla-Gullón, V. Montiel, A. Aldaz and J. Clavilier, ''Electrochemical characterization of platinum nanoparticles prepared by microemulsion: How to clean them without loss of crystalline surface structure'' Journal of Electroanalytical Chemistry 2000, 491, 69-77.
[42] J. Solla-Gullón, V. Montiel, A. Aldaz and J. Clavilier, ''Synthesis and electrochemical decontamination of platinum-palladium nanoparticles prepared by water-in-oil microemulsion'' Journal of the Electrochemical Society 2003, 150, E104-E109.
[43] T. S. Ahmadi, Z. L. Wang, T. C. Green, A. Henglein and M. A. El-Sayed, ''Shape-controlled synthesis of colloidal platinum nanoparticles'' Science 1996, 272, 1924-1926.
[44] T. S. Ahmadi, Z. L. Wang, A. Henglein and M. A. El-Sayed, ''"Cubic" colloidal platinum nanoparticles'' Chemistry of Materials 1996, 8, 1161-1163.
[45] M.-C. Daniel and D. Astruc, ''Gold Nanoparticles: Assembly, Supramolecular Chemistry, Quantum-Size-Related Properties, and Applications toward Biology, Catalysis, and Nanotechnology'' Chemical Reviews 2003, 104, 293-346.
[46] J. Solla-Gullón, P. Rodríguez, E. Herrero, A. Aldaz and J. M. Feliu, ''Surface characterization of platinum electrodes'' Physical Chemistry Chemical Physics 2008, 10, 1359-1373.
[47] Q. S. Chen, J. Solla-Gullón, S. G. Sun and J. M. Feliu, ''The potential of zero total charge of Pt nanoparticles and polycrystalline electrodes with different surface structure: The role of anion adsorption in fundamental electrocatalysis'' Electrochimica Acta 2010, 55, 7982-7994.
[48] T. Iwasita and F. C. Nart, ''In situ infrared spectroscopy at electrochemical interfaces'' Progress in Surface Science 1997, 55, 271-340.
[49] F. J. Vidal-Iglesias, R. M. Arán-Ais, J. Solla-Gullón, E. Herrero and J. M. Feliu, ''Electrochemical Characterization of Shape-Controlled Pt Nanoparticles in Different Supporting Electrolytes'' ACS Catalysis 2012, 2, 901-910.
[50] R. M. Arán-Ais, M. C. Figueiredo, F. J. Vidal-Iglesias, V. Climent, E. Herrero and J. M. Feliu, ''On the behavior of the Pt(100) and vicinal surfaces in alkaline media'' Electrochimica Acta 2011, 58, 184-192.
[51] Z.-Y. Zhou, Q. Wang, J.-L. Lin, N. Tian and S.-G. Sun, ''In situ FTIR spectroscopic studies of electrooxidation of ethanol on Pd electrode in alkaline media'' Electrochimica Acta 2010, 55, 7995-7999.
[52] D. Z. Jeffery and G. A. Camara, ''The formation of carbon dioxide during glycerol electrooxidation in alkaline media: First spectroscopic evidences'' Electrochemistry Communications 2010, 12, 1129-1132.
[53] J. F. Gomes and G. Tremiliosi-Filho, ''Spectroscopic Studies of the Glycerol Electro-Oxidation on Polycrystalline Au and Pt Surfaces in Acidic and Alkaline Media'' Electrocatalysis 2011, 2, 96-105.
[54] Y. Garsany, I. L. Singer and K. E. Swider-Lyons, ''Impact of film drying procedures on RDE characterization of Pt/VC electrocatalysts'' Journal of Electroanalytical Chemistry 2011, 662, 396-406.
[55] Y. Garsany, J. Ge, J. St-Pierre, R. Rocheleau and K. E. Swider-Lyons, ''Standardizing thin-film Rotating disk electrode measurements of the oxygen reduction activity of Pt/C'' ECS Transactions 2013, 58, 3-14.
References
189
[56] Y. Garsany, O. A. Baturina, K. E. Swider-Lyons and S. S. Kocha, ''Experimental methods for quantifying the activity of platinum electrocatalysts for the oxygen reduction reaction'' Analytical Chemistry 2010, 82, 6321-6328.
Capítulo 6: Electrooxidación de ácido fórmico con nanopartículas de
platino de forma controlada decoradas con talio: mejora en
la actividad electrocatalítica
193
Capítulo 6: Electrooxidación de ácido fórmico con
nanopartículas de platino de forma controlada decoradas
con talio: mejora en la actividad electrocatalítica
RESUMEN
En este capítulo se estudia la mejora en la oxidación del ácido fórmico al adsorber
talio sobre las superficies de las nanopartículas de platino con diferente forma, con el
objetivo de evitar la formación de CO que envenene la superficie catalítica y facilitar la
completa oxidación hasta CO2, intentando imitar comportamientos similares a lo obtenido
trabajando con superficies monocristalinas de platino y depositando adátomos como Bi o
Sb.
En primer lugar, se muestra el efecto de la adsorción de Tl sobre superficies
monocristalinas de Pt(100) y Pt(111) en 0.5 M H2SO4, resaltando la disminución de los
picos característicos de cada electrodo y la presencia de nuevos picos después de
adsorberse el Tl, 0.15 V en el caso del Pt(100) y 0.43 V en el del Pt(111). A continuación,
se estudia la oxidación de 0.1 M HCOOH con los mismos electrodos de platino
modificados con talio. El Pt(100), más favorable a la formación de veneno en forma de CO
al disociar el ácido fórmico, muestra una clara mejora de la actividad a bajos potenciales.
Sin embargo, en el Pt(111), no se ve un incremento de las corrientes de oxidación a ningún
potencial. A partir de estos resultados, se admite que el Tl actúa como tercer cuerpo,
impidiendo la formación de CO y favoreciendo la ruta directa en la reacción de oxidación
de ácido fórmico. Esta mejora es despreciable en el Pt(111), donde la producción de
veneno es nula.
En cuanto al uso de las nanopartículas de platino, en primer lugar se presenta la
caracterización electroquímica habitual al trabajar con las mismas muestras que en
anteriores capítulos, junto al efecto de la adsorción de Tl sobre ellas. Se observa una
Capítulo 6: Electrooxidación de ácido fórmico con nanopartículas de platino de forma controlada decoradas con talio: mejora en la actividad electrocatalítica
194
disminución de la corriente en los picos de adsorción de hidrógeno conforme aumenta la
cantidad de Tl, que al llegar a altos recubrimientos provoca que solamente sea visible una
doble capa en los perfiles voltamétricos. En este caso, el recubrimiento es complicado de
calcular, por lo que se le denomina durante todo el capítulo como recubrimiento máximo.
Al estudiar la oxidación del ácido fórmico en las nanopartículas de platino
modificadas con talio, las voltametrías cíclicas corroboran el efecto positivo de la
adsorción de talio sobre todo con la disminución del potencial de inicio de oxidación del
ácido fórmico hasta valores tan bajos como 0.08 V vs RHE. Como era de esperar, la
mejora electrocatalítica es mayor en las nanopartículas (100)Pt que en las (111)Pt, debido a
la menor tendencia para la formación de CO en estas últimas superficies. Posteriormente se
compara la actividad de ambas muestras al introducir el máximo recubrimiento de talio,
confirmando el mayor factor de mejora para las nanopartículas de (100)Pt, que llega a ser
hasta de 1.5 veces mayor.
De manera similar a los estudios anteriores con nanopartículas, las
cronoamperometrías evalúan la estabilidad con el tiempo de los electrodos modificados
con Tl a un potencial de 0.2 V, donde la actividad aumenta debido al impedimento en la
formación de CO. Este mismo resultado se confirma con los experimentos de FTIR
realizados con la muestra de nanopartículas de (100)Pt, donde las bandas de CO a bajos
potenciales desaparecen cuando el electrodo es modificado con Tl hasta el recubrimiento
máximo, al contrario que las bandas de CO2, las cuales sí se observan a bajos potenciales.
Para los experimentos FTIR se trabajó con una concentración 0.05 M de ácido fórmico y
0.1 M de H2SO4, para evitar elevadas formaciones de CO2 que desestabilicen la
configuración de doble capa e impedir también daños en el prisma de CaF2.
En la parte final del capítulo, se estudia el efecto que tiene la concentración del ácido
fórmico en su oxidación para las dos muestras modificadas con un recubrimiento máximo
de Tl. En las voltametrías cíclicas se produce un aumento de la actividad con la
concentración de ácido fórmico. Se esperaría que las corrientes de oxidación fueran
directamente proporcionales a la concentración de ácido fórmico. Sin embargo, al realizar
la representación logarítmica log j vs log [HCOOH], la pendiente toma un valor de 0.75 en
lugar del esperado valor de 1, revelando la influencia de especies adicionales en el
Resumen
195
mecanismo de reacción. Las corrientes transitorias registradas a un potencial de 0.2 V,
muestran una mayor actividad conforme aumenta la concentración, al igual que en el caso
de las voltametrías cíclicas, sobre todo a partir de valores de 0.1 M. Por último, se resumen
los datos de corrientes obtenidas en las cronoamperometrías después de 10 min,
considerando que casi se ha alcanzado un estado estacionario y ratificando la mucha mayor
actividad para las nanopartículas de (100)Pt en el rango de concentraciones estudiado.
197
Chapter 6
This chapter has been adapted and formatted from Phys. Chem. Chem. Phys. 2014, 16, 13616-13624.
Corresponding author: [email protected]
Chapter 6: Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity
198
6.1 Introduction
Formic acid is among the most promising fuels for anodic reactions in
electrochemical energy conversion devices such as Polymer Electrolyte Membrane (PEM)
fuel cells [1, 2]. Assuming that the change in the Gibbs free energy for the reaction in the
fuel cell (HCOOH + 1/2O2 → CO2 + H2O) is ΔGo ≈ −285 kJ mol−1 [3], the standard
electrode potential for the formic acid/CO2 redox couple is ca. −0.25 V. However, formic
acid electro-oxidation takes place at potentials that are 0.6 V higher than the reversible
thermodynamic potential on platinum electrodes [4, 5]. From an electrocatalytic point of
view, this large overpotential is mainly due to the high resistance to the oxidation of
intermediate products that diminish the performance of platinum as an anode catalyst by
blocking surface sites [6]. In this sense, many studies on formic acid electro-oxidation
reaction aim at developing new electrocatalytic materials which present higher selectivity
than platinum electrodes for the formic acid dissociation. In this respect, the mechanism of
formic acid electro-oxidation occurs through two parallel routes on platinum electrodes [7-
11]. In one of these pathways, HCOOH is oxidized through an active intermediate, which
decomposes to yield CO2. In the other reaction pathway, i.e. the indirect one, the reaction
mechanism occurs through the non-faradaic dehydration reaction of formic acid yielding
COads and water molecules. The latter reaction also takes place at open circuit potential on
platinum [12] and requires more surface sites than the active intermediate reaction path
[13]. Since the oxidation of COads requires a large overpotential, this species is considered
to be a poisoning intermediate.
It is also known that the formic acid electro-oxidation reaction is very sensitive to the
local surface structure [5, 14, 15]. Concerning this point, it was shown that the Pt(100)
electrode was the most active among platinum basal planes, while the activity was
observed for Pt(111) for both routes [5]. To modify the electrocatalytic activity and/or
selectivity of bare substrates for the different routes, the presence of other species such as
foreign atoms is a powerful strategy. In fact, many studies on modified single crystal Pt
electrodes with Sb [16], Bi [17], Pb [18], Pd [19] and Te [20] show an improvement in the
catalytic performance of these materials towards formic acid oxidation. These
electrocatalytic improvements by foreign atoms are possible due to: (i) a third-body effect,
where adatoms block neighboring sites required for COads formation [13]; (ii) electronic
Introduction
199
effects, where the foreign adatoms modify the adsorption energy between the adsorbate
and the substrate facilitating the oxidation reaction [12, 13, 21]; and (iii) a bifunctional
mechanism, where, in this case, the presence of foreign atoms can reduce the overpotential
for COads oxidation providing easily activated oxygen-species at lower potentials than
those on the corresponding bare substrate [22].
From an applied point of view, the use of single crystal surfaces is not feasible and
nanomaterials with a much higher surface to volume ratio are required. Since the
development of methods to synthesize shape-controlled Pt nanoparticles [23] and their first
use in electrocatalysis [24], many studies have been focused on the evaluation of the
electrocatalytic properties of these shaped Pt particles for oxidation reactions of promising
fuels, such as formic acid [25, 26]. For this reaction, shape-controlled Pt nanoparticles
have confirmed the structural electrocatalytic dependence related to the presence of facets
with 100 and 111 symmetry. Thus, Pt nanoparticles rich in 100 facets are the most
electroactive applicable system towards formic acid oxidation. Unfortunately, shaped Pt
nanoparticles also show a high CO poisoning rate [26].
As has been done with platinum single crystals, in order to increase the activity
and/or to overcome the poisoning effect, Pt nanoparticles have been decorated with
adatoms such as Pd [27, 28], Bi [29, 30], or Sb [31]. In addition, Pt/Pd alloyed [32] and
PtBi intermetallic nanoparticles [33] have also been tested. Based on the reported results in
ref. [28] and [29] it can be proposed that the improvement in electrocatalytic activity seems
to be mainly related to the geometry of the surface atoms of the shaped nanoparticles and
the chemical nature of foreign adatoms.
Studies in the 1980s showed that thallium (Tl) UPD (under potential deposition) on
both polycrystalline platinum and gold increases the rate of formaldehyde electro-oxidation
[34, 35]. However, even considering these promising results, almost no studies have been
devoted to the impact of Tl in the electrocatalysis of formic acid [36]. For that reason, we
report in this paper an electrochemical and spectroscopic (in situ FTIR – Fourier
Transform Infrared) study on the electrocatalytic properties of Tl-decorated shape-
controlled Pt nanoparticles towards HCOOH electrooxidation.
Chapter 6: Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity
200
6.2 Experimental
Platinum single crystal surfaces were prepared following the method developed by
Clavilier et al. [37] from single crystal beads (ca. 2 mm in diameter). Before the
experiments, working electrodes were flame annealed during 30 s, cooled down in a H2/Ar
atmosphere and quenched in ultrapure water in equilibrium with this atmosphere before
they were transferred to the electrochemical cell [38]. Cubic and octahedral shape-
controlled Pt nanoparticles, denoted as (100)Pt and (111)Pt respectively, were employed.
The synthesis of these shape-controlled Pt nanoparticles was performed as previously
described in detail [39]. Transmission Electron Microscopy (TEM) measurements were
performed to estimate both particle size and morphology/shape [39].
For electrochemical and in situ FTIR measurements, the nanoparticles dispersed in
water were deposited on a polished gold disk and dried under argon atmosphere.
Thereafter, the nanoparticles were cleaned by CO (N47, Air Liquide) monolayer
adsorption and stripping treatment before the experiments, avoiding high potential
excursions to preserve surface order. The active area of platinum nanoparticles was
calculated by measuring the charge involved in the so-called hydrogen UPD region after
the subtraction of the conventional double-layer contribution in 0.5 M H2SO4 solution,
using a reference value of 0.23 mC cm−2 [40]. A small quantity of nanoparticles (with an
active area of ca. 0.05–0.1 cm2) was deposited in all the experiments in order to
avoid/minimize transport problems of the reactant species to the surface of the
nanoparticles [41].
The deposition of Tl on Pt was performed using dilute concentrations of 10−4–10−5 M
Tl2SO4 (Aldrich® 99.995%) in 0.5 M H2SO4 solution, cycling the electrode potential
between 0.06 V and 0.90 V at 0.05 V s−1. The Tl coverage was monitored through the
decrease of the hydrogen adsorption/desorption peaks, according to the equation:
θ𝑇𝑙 = 1 − θH = 𝑞𝐻0 − 𝑞𝐻𝑇𝑙
𝑞𝐻0
(6.1)
where q0H and qTl
H are the hydrogen adsorption charges of the clean and thallium modified
electrodes respectively, which were also calculated after the subtraction of the double layer
charging contribution. In the case of platinum single crystals, the electrodes were cycled in
Experimental
201
specific potential ranges to preserve the surface order and to avoid problems of Tl
desorption at higher potentials.
A platinum wire was used as a counter electrode, and a reversible hydrogen (N50,
Air Liquide) electrode (RHE) was employed as a reference electrode. All potentials used in
this paper are referenced to the RHE. Experiments were carried out in 0.5 M H2SO4
(Merck KGaA Suprapur® 96%), prepared in ultrapure water (Elga PureLab Ultra 18.2 MΩ
cm), and deareated with Ar (N50, Air Liquide). Formic acid (Merck KGaG 98%) oxidation
experiments were performed in 0.5 M H2SO4.
For electrochemical measurements, cyclic voltammetry and chronoamperometry
were employed using a waveform generator (EG&G PARC 175) together with a
potentiostat (eDAQ EA161) and a digital recorder (eDAQ ED401).
In situ FTIR spectra were acquired using a Nicolet (Model 8700) spectrometer,
equipped with an MCT (Mercury–Cadmium–Telluride) detector. The
spectroelectrochemical cell was fitted with a prismatic 60° CaF2 window, as described
previously [42]. The spectra, obtained from the average of 100 interferograms using a
resolution of 8 cm−1, were collected at intervals of 50 mV between 0.05 V to 0.90 V vs.
RHE. For all experiments, p-polarized light was employed, which allows detecting changes
in the concentration of active species on the electrode surface and electrolyte solution [42].
Spectra are presented in absorbance units A=-log[(R1-R2)/R1] in which R2 and R1 are
referred to as the reflectance values of the single beam spectra corresponding to the sample
and the reference potentials, respectively. Positive bands in the spectra are related to
species that have been formed at the sample potential whereas negative bands correspond
to species consumed. All the experiments were performed at room temperature.
Chapter 6: Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity
202
6.3 Results and discussion
6.3.1 Formic acid oxidation on Tl-modified Pt single crystal electrodes
Preliminary experiments with Pt(100) and Pt(111) single crystal electrodes were
performed to evaluate the effects of the Tl adsorption on these Pt model surfaces both in
the absence and presence of formic acid. Fig. 6.1 shows voltammetric results for Tl
modified Pt(100) and Pt(111) single crystal electrodes in a 0.5 M H2SO4 solution. The
effect of Tl deposition can be easily monitored by the changes in the cyclic voltammetric
profile. In addition, in order to avoid possible Tl dissolution, the upper potential limits
were set at 0.65 and 0.6 V for Pt(100) and Pt(111) electrodes, respectively.
Fig. 6.1. Evolution of the voltammetric profiles in 0.5 M H2SO4 with increasing amounts of Tl on (a)
Pt(100) and (b) Pt(111). Scan rate: 0.05 V s-1. Arrows indicate changes associated with increasing Tl amounts
at the surface.
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7-200
-100
0
100
200
300 Bare θTl= 0.20 θTl= 0.32 θTl= 0.40 θTl= 0.61 θTl= 0.78
E vs RHE / V
a
b
E vs RHE / V
j / µ
Acm
-2
0.0 0.2 0.4 0.6 0.8 1.0
-100
-50
0
50
100
Bare θTl= 0.16 θTl= 0.56 θTl= 0.63
Results and discussion
203
For the Pt(100) electrode (Fig. 6.1a), the adsorption/desorption states between 0.2
and 0.5 V (which are associated with the competitive adsorption between hydrogen and
anions) remarkably decrease during Tl deposition, whereas a small peak appears at about
0.15 V at Tl coverages close to the full blockage.
In the case of the Pt(111) electrode, Fig. 6.1b, similar effects are observed for the
diminution of the charge in the hydrogen adsorption/desorption region (between 0.06 and
0.35 V) and the (bi)sulfate adsorption (between 0.35 and 0.65 V). Again, a new small peak
for this electrode appears at about 0.43 V at high coverages of Tl. This peak is associated
with the adsorption of sulfate on the modified electrode, because it is absent in perchloric
acid solutions. Although it appears in the same potential region that the spike in sulfuric
acid solutions for the Pt(111) electrode, the origin is not the same. The spike at 0.45 V
diminishes upon Tl deposition and at a given Tl coverage the new peak appears. It is then
probably related to structural changes in the adlayer that changes the interaction of sulfate
with the electrode surface.
The positive going sweep voltammetric profiles of formic acid oxidation for the
same Tl-modified Pt single crystal electrodes from Fig. 6.1 are presented in Fig. 6.2, using
0.1 M HCOOH in 0.5 M H2SO4 as test solution. As expected, very low currents are
observed for the bare Pt(100) electrode as a consequence of the well-established CO
poisoning process coming from the dehydration of formic acid, which is favored on
Pt(100) [11]. With increasing amounts of Tl, the indirect path (through CO poisoning) is
hindered. Then formic acid oxidation can take place through the direct path and oxidation
currents increase very significantly. The results suggest an optimum Tl coverage at values
close to 0.4. At higher coverages, the onset potential increases and the current diminishes.
However, in the case of the Pt(111) electrode (Fig. 6.2b), for which it is well-
established that the CO poisoning is almost negligible [11], the addition of Tl does not
provide significant changes in the electrooxidation process. These results seem to indicate
that Tl acts as a third body preventing the dehydration reaction. For the Pt(111) electrode,
owing to the almost negligible CO formation rate [5], the presence of Tl does not improve
its catalytic activity. The current diminution for this electrode is just the result of the
diminution of the Pt free sites.
Chapter 6: Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity
204
Fig. 6.2. Positive sweep voltammetric profiles for 0.1 M formic acid oxidation in 0.5 M H2SO4 with
and without Tl for (a) Pt(100) and (b) Pt(111) single crystals. Scan rate: 0.02 V s-1.
On the other hand, the increase of activity for the Pt(100) electrode can be related to
the diminution of the COads coverage which leads to an increase of the oxidation through
the active intermediate reaction path. However, electronic effects cannot be discarded for
this electrode. It should be noted that the onset for the direct oxidation reaction in the
absence of poison on the Pt(100) electrode is 0.30 V (see ref. [43]), whereas in the
presence of Tl the onset is ca. 0.20 V. This diminution of the onset potential at a Tl
coverage of ca. 0.4 suggests the possible presence of an electronic effect. These results
also point out the importance of controlling the surface structure of the Pt substrate, the
Pt(100) square structure being much more convenient than the hexagonal Pt(111). Thus, in
terms of the particle shape, it would be preferable to use cubic Pt nanoparticles in which
the number of 100 surface sites is maximized [44].
0.0 0.2 0.4 0.6 0.8 1.00.00.51.01.52.02.53.03.54.0
Bare θTl= 0.20 θTl= 0.32 θTl= 0.40 θTl= 0.61 θTl= 0.78
a
b
0.0 0.2 0.4 0.6 0.8 1.00.0
0.5
1.0
1.5
2.0
2.5
Bare θTl= 0.16 θTl= 0.56 θTl= 0.63
j / m
Acm
-2
E vs RHE / V
E vs RHE / V
Results and discussion
205
6.3.2 Electrochemical characterization of Tl modified Pt nanoparticles
Fig. 6.3 displays the voltammetric profiles of the (100)Pt and (111)Pt nanoparticles
before and after Tl incorporation. Before the Tl decoration, the voltammetric profiles of the
cubic and octahedral Pt nanoparticles are those that are expected from their shape–surface
structure relationship [45]. Thus, the cubic Pt nanoparticles show the main features related
to a preferential 100 surface structure, that is, a sharp peak at ∼0.27 V related to 100
edge/corner sites and a signal around 0.37 V associated with wide 100 terrace sites. In
contrast, the octahedral nanoparticles show the characteristics of a preferential 111
surface structure, with a broad peak at about 0.52 V related to sulfate adsorption on
relatively wide two-dimensional 111 terrace sites. A detailed analysis of the
characteristic voltammetric features of similar shape-controlled Pt nanoparticles was
described in previous contributions [44].
Fig. 6.3. Voltammetric profiles for increasing amounts of Tl coverages on (a) (100)Pt and (b) (111)Pt
nanoparticles in 0.5 M H2SO4 + 10-4 ~ 10-5 M Tl2SO4. Scan rate: 0.05 Vs-1.
0.0 0.2 0.4 0.6 0.8 1.0
-100
-50
0
50
100a
θTl= 0 θTl= 0.34 θTl= 0.56 θTl maximum
j / µ
A cm
-2
b
0.0 0.2 0.4 0.6 0.8 1.0-150
-100
-50
0
50
100
150
E vs RHE / V
θTl= 0 θTl= 0.18 θTl= 0.42 θTl maximum
Chapter 6: Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity
206
Fig. 6.3 also shows the voltammetric responses of the (100)Pt and (111)Pt
nanoparticles after partial and maximum deposition of Tl. The evolution of the
voltammetric profiles is similar to those previously reported for Pd and Bi on shape-
controlled Pt nanoparticles [28, 29] or after deposition of Bi(III), Te(IV) and Se(IV) on
stepped Pt surfaces [46]. In addition, the Tl adsorption process does not produce
appreciable changes in the charge density on the so-called double layer region until high
thallium coverages are reached. As described in the experimental section, the Tl coverage
can be calculated considering the expression θTl = 1 − θH, where θTl and θH are the thallium
and hydrogen coverages, respectively. However, at the maximum thallium coverage on
both Pt nanoparticles, Fig. 6.3, an important increase of the double layer region is
observed. This fact prevents an accurate determination of the Tl coverage for highly
covered surfaces that cannot be properly calculated. For that reason, the maximum
coverage for each sample will be referred to as “maximum” and no numeric value will be
given. In addition, it is important to note the absence of additional voltammetric features at
high coverages and remark that only a small broad peak is visible at about 0.70 V,
particularly in the preferential (111)Pt nanoparticles. This feature can be linked to the
thallium desorption from (111) terrace sites, as pointed out for Tl UPD in Pt(111) reports
[47, 48].
6.3.3 Formic acid oxidation on Tl modified shape controlled Pt nanoparticles
After each particular Tl adsorption, the modified Pt nanoparticles were transferred to
a second electrochemical cell containing 0.1 M formic acid + 0.5 M H2SO4. Fig. 6.4
compares the positive going sweep voltammetric responses obtained for the bare and Tl
modified shaped nanoparticles. For the bare cubic (100)Pt nanoparticles (Fig. 6.4a, black
line), the positive going scan shows almost zero current density at potentials below 0.35 V,
due to CO poisoning effects. The HCOOH oxidation starts at around 0.35 V, and the
current density increases slowly until ∼0.80 V. Above this potential, the current density
starts to grow rapidly due to CO oxidation and therefore in the reverse scan the current
density would be much higher as the surface is CO-free. As before, these negative-going
results are not shown, because they are irrelevant in electrocatalytic studies [26, 39].
Results and discussion
207
Interestingly, for Tl modified cubic (100)Pt nanoparticles with θTl = 0.34 and 0.56, Fig.
6.4a (red and green lines, respectively), the onset potential of HCOOH oxidation
remarkably decreases to about 0.1 V. Moreover, at the maximum coverage (blue line), the
onset potential is even lower (about 0.08 V). This feature clearly evidences the positive
impact of thallium on the electro-oxidation of formic acid in the low potential region.
Fig. 6.4. Positive sweep voltammetric profiles for formic acid electro-oxidation with increasing
amounts of Tl coverages for (a) (100)Pt and (b) (111)Pt nanoparticles. Scan rate: 0.02 Vs-1. Test solution: 0.1
M formic acid in 0.5 M H2SO4.
For the (111)Pt nanoparticles, Fig. 6.4b, a similar effect on the onset potential is
observed after surface decoration with Tl. Taking into account that (i) the 111 domains
do not suffer the same strong CO poisoning effect as that observed with the 100 domains
[11] (see Fig. 6.2) and (ii) the 111 domains have a low catalytic activity for the direct
oxidation [5], the electrocatalytic enhancement observed is lower than that reported for the
Chapter 6: Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity
208
(100)Pt nanoparticles. Anyhow, the onset potential diminishes when θTl increases,
decreasing to around 0.1 V at the maximum coverage (blue line). Also, the onset for the
formic acid oxidation observed for the Tl modified nanoparticles at high coverages is ca.
0.2–0.3 V lower than the onset for the direct oxidation route in the unmodified
nanoparticles [26].
Finally, with the aim of comparing the activity of both samples in the whole potential
range, Fig. 6.5 displays the HCOOH activity ratio between the bare and Tl modified
(maximum coverage) Pt nanoparticles. From Fig. 6.5, it is evident that the “improvement
factor” due to the presence of Tl for the (100)Pt nanoparticles is larger than that obtained
with the (111)Pt nanoparticles in the entire potential range. In fact, the highest ratio
between both activities is observed at ca. 0.3 V, the potential at which the 100 domains
have the greatest activity, in agreement with the large catalytic activity of Tl on the 100
domains (Fig. 6.2a). In addition, in terms of maximum currents, the electrooxidation
activity of the Tl-modified (100)Pt nanoparticles is always higher (about 1.5 times) than
that of the (111)Pt nanoparticles, Fig. 6.6.
Fig. 6.5. Ratio between the HCOOH oxidation current densities obtained with the bare and Tl-
decorated (maximum coverage) shape-controlled Pt nanoparticles. Data taken from Fig. 6.4.
0.0 0.2 0.4 0.6 0.80
2
4
6
8
10
12
14
16
18
20
(100)Pt nanoparticles (111)Pt nanoparticles
E vs RHE / V
j θmax
Tl /
j Bare
Results and discussion
209
Fig. 6.6. Ratio between the HCOOH oxidation current densities obtained using Tl-modified
(maximum coverage) (100) and (111)Pt nanoparticles. Data taken from Fig. 6.4.
In order to better evaluate the activity as well as the stability of the Tl-modified
samples, current transient responses for each modified electrode were recorded at 0.2 V
(Fig. 6.7), a reasonably low potential value. In these experiments, a pretreatment consisting
of a potential step at 0.85 V for 10 s prior to the potential step at 0.2 V was performed in
order to oxidize all the possible CO blocking surface sites [26]. Current transients for the
bare nanoparticles are not reported, as current densities for both samples are almost zero.
This is due to the fact that the CO formation rate is very high and the surface is
immediately covered by CO after the cleaning step. For Tl modified (100)Pt nanoparticles
(Fig. 6.7a) the current densities after 600 s are 0.002, 0.010 and 0.014 mA cm−2 at Tl
coverages of 0.25, 0.48 and the maximum one, respectively. For Tl modified (111)Pt
nanoparticles (Fig. 6.7b), reactivity is lower and current densities of 0.002, 0.004 and 0.006
mA cm−2 were obtained at coverages of 0.43, 0.57 and the maximum one, respectively.
These results indicate that Tl adsorbed on the surface successfully hinders the CO
adsorption through the poisoning pathway, and this effect increases with the Tl coverage.
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.91.0
1.2
1.4
1.6
1.8
2.0
j (100
)Ptθ
max
Tl /
j (111
)Ptθ
max
Tl
E vs RHE / V
Chapter 6: Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity
210
Fig. 6.7. Current transients recorded at 0.2 V for formic acid electrooxidation for (a) (100)Pt and (b)
(111)Pt nanoparticles with different Tl coverages. Test solution: 0.1 M formic acid in 0.5 M H2SO4.
6.3.4 FTIR experiments of formic acid oxidation on Tl-decorated Pt
nanoparticles
In situ FTIR spectra were measured in order to better understand the role of Tl in the
enhancement of formic acid oxidation on the modified nanoparticles. Only the (100)Pt
nanoparticles were studied because these nanoparticles present more COads than the (111)Pt
nanoparticles [39, 49], and then, it is easier to determine the electrocatalytic effects
induced by the presence of Tl. Spectra were collected in 0.05 M formic acid in 0.1 M
H2SO4 on non-modified and Tl-modified electrodes (at maximum thallium coverage).
0 100 200 300 400 500 6000.00
0.01
0.02
0.03
0.04
0.05
0.06
0 100 200 300 400 500 6000.00
0.01
0.02
0.03
0.04
0.05
0.06
a Thallium coverage
j/mA
cm-2
θ=0.25 θ=0.48 θ maximum
b Thallium coverage
t/s
θ=0.43 θ=0.57 θ maximum
Results and discussion
211
Formic acid concentration was diminished with the aim of decreasing the huge amount of
CO2 formed during formic acid oxidation, which destabilizes the thin-layer configuration.
Sulfuric acid concentration was also reduced in order to avoid possible damage in the CaF2
prism. For all spectra presented, the spectrum acquired at 0.05 V was used as a reference.
Fig. 6.8. In situ FTIR spectra for formic acid electro-oxidation on (100)Pt nanoparticles: (a) bare Pt
and (b) maximum Tl coverage. Reference spectra were taken at 0.05 V. Test solution: 0.05 M formic acid in
0.1 M H2SO4.
Fig. 6.8a displays the spectra for formic acid oxidation on (100)Pt bare nanoparticles.
From 0.2 V to 0.6 V, the spectra show the linearly adsorbed CO band between 2050 and
2060 cm−1 [42]. At 0.2 V, the band frequency is around 2052 cm−1, whereas at 0.6 V the
frequency shifts to 2060 cm−1, likely due to the Stark effect [50]. Between 0.4 and 0.5 V,
the band shows a slightly bipolar character, meaning that adsorbed CO was present in the
reference potential (0.05 V) [42]. At around 0.2 V, a new band at 2343 cm−1 appears,
which is associated with the start of CO2 formation [42]. The spectra do not show any
signal band that could be attributed to bridge adsorbed CO, which should appear at around
1820 cm−1 as was observed for formic acid oxidation in ATR-SEIRA (Attenuated Total
2400 2200 2000 1800 2400 2200 2000 1800
a
CO2 formation
υ/cm-1
0.10 V0.20 V0.25 V0.30 V0.40 V
0.50 V
0.60 V
CO adsorbed
CO2 formationb0.01 a.u.
0.10 V0.15 V
0.20 V
0.30 V
0.40 V
0.50 V
0.60 V0.01 a.u.
Chapter 6: Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity
212
Reflection – Surface Enhanced Infra-Red Absorption) experiments on thin-film
polycrystalline platinum electrodes at 0.35 V vs. RHE [9].
Fig. 6.8b shows the spectra for formic acid oxidation on Tl-modified (100)Pt
nanoparticles. The band for CO2 can be clearly observed at 0.1 V, and the COads band is
absent for all the spectra, pointing out that Tl enhances the electrocatalytic activity (Fig.
6.4a) by hindering the poisoning pathway thus allowing formic acid oxidation to proceed
through the direct pathway, which also explains why CO2 is formed at low potentials.
6.3.5 Effect of formic acid concentration
Once the catalytic effect of Tl over Pt nanoparticles for formic acid oxidation has
been confirmed, experiments using different formic acid concentrations were also
performed with the maximum Tl coverage to evaluate its possible effect on the
electrocatalytic activity. The corresponding potentiodynamic responses are shown in Fig.
6.9, for both (100)Pt and (111)Pt nanoparticles. In the two cases, current densities increase
with the concentration of formic acid, especially at low potentials. In principle, it would be
expected that currents were directly proportional to the concentration of formic acid, that
is, j ∝ Co*. Thus, the representation of log(j) at a given potential vs. log(Co*) should be
linear with a slope of 1, the expected reaction order for the formic acid concentration. The
plots are linear in the range between 0.2 and 0.7 V in both scan directions (inset of Fig.
6.9b). However, the slope is 0.75 ± 0.03 in this potential range for both electrodes, which
would indicate that the reaction order is 0.75. This fact clearly suggests that the reaction
mechanism is complex. It could be argued that the complexity is due to the presence of the
two routes for the reaction. However, it is known that the CO formation reaction occurs in
the potential window lower than 0.5 V [26]. Thus, the oxidation reaction in the negative
scan at E > 0.5 V would take place on a clean surface and only through the active
intermediate. Moreover, the presence of Tl has suppressed the route through CO
significantly. The constant value for the reaction order in the whole range, then, suggests
that the complexity is not due to the CO route, but there is an intrinsic factor in the direct
Results and discussion
213
oxidation route. This fact would indicate that an additional species (not only formic acid) is
involved in the reaction mechanism.
Fig. 6.9. Positive sweep voltammetric profiles for (a) (100)Pt and (b) (111)Pt nanoparticles with
maximum Tl coverage in different concentrations of formic acid in 0.5 M H2SO4. Scan rate: 0.02 Vs-1. Inset:
double logarithmic plot of the current density at 0.5 V for the (111)Pt nanoparticles vs. formic acid
concentration.
Additional evidence on that is found in the chronoamperometric responses after 600
s of reaction at 0.2 V for both nanoparticles at maximum Tl coverage at different formic
acid concentrations (Fig. 6.10). In the case of (100)Pt nanoparticles (Fig. 6.10a), there is
0
5
10
15
20
0.0 0.2 0.4 0.6 0.8 1.0
a
E vs RHE/V
b
0.0 0.2 0.4 0.6 0.8 1.00
5
10
15
20
0.1 11
10
j/mAc
m-2
[HCOOH]/M
j / m
Acm
-2
E vs RHE/V
0.05 M 0.1 M 0.2 M 0.5 M 1 M
Chapter 6: Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity
214
nearly no clear difference between the final current density for 0.05 M and 0.1 M (around
0.015–0.020 mA cm−2), but for the other concentrations, current density increases with the
amount of formic acid in solution, increasing up to 0.145 mA cm−2 for 1 M formic acid
concentration. A similar behavior was observed for (111)Pt nanoparticles in Fig. 6.10b,
with a final current density of 0.049 mA cm−2 for 1 M formic acid. As for voltammetric
curves, chronoamperometric currents become higher when the concentration of formic acid
increases. Fig. 6.11 summarizes the differences observed for the final current density after
10 min at 0.2 V for both samples at maximum coverage, clearly indicating that the Tl-
modified (100)Pt nanoparticles are much more active than the (111)Pt nanoparticles in the
range of HCOOH concentration under study (0.05–1 M HCOOH). Currents recorded after
10 minutes reflect a nearly stationary situation. For the currents at 10 min the reaction
order is similar to that measured by voltammetry, which reinforces the fact that the
reaction mechanism through the active intermediate is complex.
Fig. 6.10. Current transients for (a) (100)Pt and (b) (111)Pt nanoparticles with maximum Tl coverage
recorded at 0.20 V for different formic acid concentrations in 0.5 M H2SO4.
0 100 200 300 400 500 6000.0
0.1
0.2
0.3
0.4
0.5a
j/mA
cm-2
0.05 M 0.1 M 0.2 M 0.5 M 1 M
b
0 100 200 300 400 500 6000.0
0.1
0.2
0.3
0.4
0.5
t/s
0.05 M 0.1 M 0.2 M 0.5 M 1 M
Results and discussion
215
Fig. 6.11. Comparison between formic acid concentrations and current densities obtained after 10
minutes at 0.20 V Data extracted from Fig. 6.10 for (a) (100)Pt and (b) (111)Pt nanoparticles.
0.0 0.2 0.4 0.6 0.8 1.00.00
0.05
0.10
0.15
0.20a
j 600
s/mA
cm-2
b
0.0 0.2 0.4 0.6 0.8 1.00.00
0.05
0.10
0.15
0.20
[HCOOH]/mol L-1
Chapter 6: Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity
216
6.4 Conclusions
The deposition of Tl on (100)Pt and (111)Pt nanoparticles remarkably improves their
electrocatalytic activity towards formic acid oxidation, especially in the low potential
region. The activity enhancement is also dependent on the surface structure of the Pt
substrate. In agreement with fundamental data from Pt single crystal studies, the use of
(100)Pt nanoparticles is clearly more beneficial than the use of (111)Pt nanoparticles.
Voltammetric and in situ FTIR data indicate that Tl decoration prevents the formation of
adsorbed COads. Consequently, it can be concluded that the enhancement of formic acid
oxidation with Tl-decorated platinum nanoparticles (especially with (100)Pt nanoparticles)
is due to the hindrance of the indirect pathway (third body effect). So, the reaction mainly
takes place through the direct pathway (via non-COads). However, electronic effects cannot
be discarded, due to the diminution of the onset potential for the formic acid oxidation
reaction.
References
217
6.5 References
[1] C. Rice, R. I. Ha, R. I. Masel, P. Waszczuk, A. Wieckowski and T. Barnard, ''Direct formic acid fuel cells'' Journal of Power Sources 2002, 111, 83-89.
[2] N. V. Rees and R. G. Compton, ''Sustainable energy: A review of formic acid electrochemical fuel cells'' Journal of Solid State Electrochemistry 2011, 15, 2095-2100.
[3] S. Uhm, H. J. Lee and J. Lee, ''Understanding underlying processes in formic acid fuel cells'' Physical Chemistry Chemical Physics 2009, 11, 9326-9336.
[4] G. Q. Lu, A. Crown and A. Wieckowski, ''Formic acid decomposition on polycrystalline platinum and palladized platinum electrodes'' Journal of Physical Chemistry B 1999, 103, 9700-9711.
[5] V. Grozovski, V. Climent, E. Herrero and J. M. Feliu, ''Intrinsic activity and poisoning rate for HCOOH oxidation on platinum stepped surfaces'' Physical Chemistry Chemical Physics 2010, 12, 8822-8831.
[6] C. Rice, S. Ha, R. I. Masel and A. Wieckowski, ''Catalysts for direct formic acid fuel cells'' Journal of Power Sources 2003, 115, 229-235.
[7] A. Capon and R. Parsons, ''The oxidation of formic acid at noble metal electrodes Part III. Intermediates and mechanism on platinum electrodes'' Journal of Electroanalytical Chemistry 1973, 45, 205-231.
[8] M. Osawa, K. Komatsu, G. Samjeske, T. Uchida, T. Ikeshoji, A. Cuesta and C. Gutiérrez, ''The Role of Bridge-Bonded Adsorbed Formate in the Electrocatalytic Oxidation of Formic Acid on Platinum'' Angewandte Chemie-International Edition 2011, 50, 1159-1163.
[9] A. Cuesta, G. Cabello, M. Osawa and C. Gutiérrez, ''Mechanism of the Electrocatalytic Oxidation of Formic Acid on Metals'' ACS Catalysis 2012, 2, 728-738.
[10] Y. X. Chen, M. Heinen, Z. Jusys and R. J. Behm, ''Bridge-bonded formate: Active intermediate or spectator species in formic acid oxidation on a Pt film electrode?'' Langmuir 2006, 22, 10399-10408.
[11] J. M. Feliu and E. Herrero, ''Formic acid oxidation'', in Handbook of Fuel Cells - Fundamentals, Technology and Applications, vol. 2, W. Vielstich, H. Gasteiger and A. Lamm (Eds.) Wiley, Chichester, 2003, pp. 625-634.
[12] E. Herrero, A. Fernández-Vega, J. M. Feliu and A. Aldaz, ''Poison formation reaction from formic acid and methanol on Pt(111) electrodes modified by irreversibly adsorbed Bi and As'' Journal of Electroanalytical Chemistry 1993, 350, 73-88.
[13] E. Leiva, T. Iwasita, E. Herrero and J. M. Feliu, ''Effect of adatoms in the electrocatalysis of HCOOH oxidation. A theoretical model'' Langmuir 1997, 13, 6287-6293.
[14] S. G. Sun and Y. Y. Yang, ''Studies of kinetics of HCOOH oxidation on Pt(100), Pt(110), Pt(111), Pt(510) and Pt(911) single crystal electrodes'' Journal of Electroanalytical Chemistry 1999, 467, 121-131.
[15] A. Cuesta, M. Escudero, B. Lanova and H. Baltruschat, ''Cyclic Voltammetry, FTIRS, and DEMS Study of the Electrooxidation of Carbon Monoxide, Formic Acid, and Methanol on Cyanide-Modified Pt(111) Electrodes'' Langmuir 2009, 25, 6500-6507.
[16] Y.-Y. Yang, S.-G. Sun, Y.-J. Gu, Z.-Y. Zhou and C.-H. Zhen, ''Surface modification and electrocatalytic properties of Pt(100), Pt(110), Pt(320) and Pt(331) electrodes with Sb towards HCOOH oxidation'' Electrochimica Acta 2001, 46, 4339-4348.
[17] S. P. E. Smith, K. F. Ben-Dor and H. D. Abruña, ''Structural effects on the oxidation of HCOOH by bismuth-modified Pt(111) electrodes with (100) monatomic steps'' Langmuir 1999, 15, 7325-7332.
[18] H. W. Lei, H. Hattori and H. Kita, ''Electrocatalysis by Pb adatoms of HCOOH oxidation at Pt(111) in acidic solution'' Electrochimica Acta 1996, 41, 1619-1628.
Chapter 6: Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity
218
[19] F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero, A. Aldaz and J. M. Feliu, ''Formic acid oxidation on Pd-modified Pt(100) and Pt(111) electrodes: A DEMS study'' Journal of Applied Electrochemistry 2006, 36, 1207-1214.
[20] E. Herrero, M. J. Llorca, J. M. Feliu and A. Aldaz, ''Oxidation of formic acid on Pt(100) electrodes modified by irreversibly adsorbed tellurium'' Journal of Electroanalytical Chemistry 1995, 383, 145-154.
[21] M. Shibata, N. Furuya, M. Watanabe and S. Motoo, ''Electrocatalysis by ad-atoms. Part XXIV. Effect of arrangement of Bi ad-atoms on formic acid oxidation'' Journal of Electroanalytical Chemistry 1989, 263, 97-108.
[22] M. Watanabe and S. Motoo, ''Electrocatalysis by ad-atoms: Part III. Enhancement of the oxidation of carbon monoxide on platinum by ruthenium ad-atoms'' Journal of Electroanalytical Chemistry 1975, 60, 275-283.
[23] T. S. Ahmadi, Z. L. Wang, T. C. Green, A. Henglein and M. A. El-Sayed, ''Shape-controlled synthesis of colloidal platinum nanoparticles'' Science 1996, 272, 1924-1926.
[24] F. J. Vidal-Iglesias, J. Solla-Gullón, P. Rodríguez, E. Herrero, V. Montiel, J. M. Feliu and A. Aldaz, ''Shape-dependent electrocatalysis: ammonia oxidation on platinum nanoparticles with preferential (100) surfaces'' Electrochemistry Communications 2004, 6, 1080-1084.
[25] N. Tian, Z.-Y. Zhou, S.-G. Sun, Y. Ding and Z. L. Wang, ''Synthesis of Tetrahexahedral Platinum Nanocrystals with High-Index Facets and High Electro-Oxidation Activity'' Science 2007, 316, 732-735.
[26] V. Grozovski, J. Solla-Gullón, V. Climent, E. Herrero and J. M. Feliu, ''Formic Acid Oxidation on Shape-Controlled Pt Nanoparticles Studied by Pulsed Voltammetry'' Journal of Physical Chemistry C 2010, 114, 13802-13812.
[27] P. Waszczuk, T. M. Barnard, C. Rice, R. I. Masel and A. Wieckowski, ''A nanoparticle catalyst with superior activity for electrooxidation of formic acid'' Electrochemistry Communications 2002, 4, 599-603.
[28] F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero, A. Aldaz and J. M. Feliu, ''Pd Adatom Decorated (100) Preferentially Oriented Pt Nanoparticles for Formic Acid Electrooxidation'' Angewandte Chemie-International Edition 2010, 49, 6998-7001.
[29] Q. S. Chen, Z. Y. Zhou, F. J. Vidal-Iglesias, J. Solla-Gullón, J. M. Feliu and S. G. Sun, ''Significantly Enhancing Catalytic Activity of Tetrahexahedral Pt Nanocrystals by Bi Adatom Decoration'' Journal of the American Chemical Society 2011, 133, 12930-12933.
[30] A. Sáez, E. Expósito, J. Solla-Gullón, V. Montiel and A. Aldaz, ''Bismuth-modified carbon supported Pt nanoparticles as electrocatalysts for direct formic acid fuel cells'' Electrochimica Acta 2012, 63, 105-111.
[31] F. J. Vidal-Iglesias, A. López-Cudero, J. Solla-Gullón and J. M. Feliu, ''Towards More Active and Stable Electrocatalysts for Formic Acid Electrooxidation: Antimony-Decorated Octahedral Platinum Nanoparticles'' Angewandte Chemie-International Edition 2013, 52, 964-967.
[32] H. Lee, S. E. Habas, G. A. Somorjai and P. Yang, ''Localized Pd overgrowth on cubic Pt nanocrystals for enhanced electrocatalytic oxidation of formic acid'' Journal of the American Chemical Society 2008, 130, 5406-5407.
[33] E. Casado-Rivera, Z. Gal, A. C. D. Angelo, C. Lind, F. J. DiSalvo and H. D. Abruña, ''Electrocatalytic oxidation of formic acid at an ordered intermetallic PtBi surface'' ChemPhysChem 2003, 4, 193-199.
[34] M. D. Spasojevic, R. R. Adzic and A. R. Despic, ''Electrocatalysis on surfaces modified by foreign metal adatoms: Oxidation of formaldehyde on platinum'' Journal of Electroanalytical Chemistry 1980, 109, 261-269.
[35] R. R. Adzic and M. L. Avramovivic, ''Improvements of the catalytic activity of gold by foreign metal ad-atoms: Oxidation of formaldehyde in alkaline solutions'' Journal of Electroanalytical Chemistry 1982, 134, 177-180.
References
219
[36] A. Kelaidopoulou, E. Abelidou and G. Kokkinidis, ''Electrocatalytic oxidation of methanol and formic acid on dispersed electrodes: Pt, Pt-Sn and Pt/M(upd) in poly(2-hydroxy-3-aminophenazine)'' Journal of Applied Electrochemistry 1999, 29, 1255-1261.
[37] J. Clavilier, D. Armand, S. G. Sun and M. Petit, ''Electrochemical adsorption behaviour of platinum stepped surfaces in sulphuric acid solutions'' Journal of Electroanalytical Chemistry 1986, 205, 267-277.
[38] J. Clavilier, K. El Achi, M. Petit, A. Rodes and M. A. Zamakhchari, ''Electrochemical Monitoring of the Thermal Reordering of Platinum Single-Crystal Surfaces after Metallographic Polishing from the Early Stage to the Equilibrium Surfaces'' Journal of Electroanalytical Chemistry 1990, 295, 333-356.
[39] J. Solla-Gullón, F. J. Vidal-Iglesias, A. López-Cudero, E. Garnier, J. M. Feliu and A. Aldaz, ''Shape-dependent electrocatalysis: methanol and formic acid electrooxidation on preferentially oriented Pt nanoparticles'' Physical Chemistry Chemical Physics 2008, 10, 3689-3698.
[40] Q. S. Chen, J. Solla-Gullón, S. G. Sun and J. M. Feliu, ''The potential of zero total charge of Pt nanoparticles and polycrystalline electrodes with different surface structure: The role of anion adsorption in fundamental electrocatalysis'' Electrochimica Acta 2010, 55, 7982-7994.
[41] S. Chumillas, C. Busó-Rogero, J. Solla-Gullón, F. J. Vidal-Iglesias, E. Herrero and J. M. Feliu, ''Size and diffusion effects on the oxidation of formic acid and ethanol on platinum nanoparticles'' Electrochemistry Communications 2011, 13, 1194-1197.
[42] T. Iwasita and F. C. Nart, ''In situ infrared spectroscopy at electrochemical interfaces'' Progress in Surface Science 1997, 55, 271-340.
[43] V. Grozovski, V. Climent, E. Herrero and J. M. Feliu, ''Intrinsic Activity and Poisoning Rate for HCOOH Oxidation at Pt(100) and Vicinal Surfaces Containing Monoatomic (111) Steps'' ChemPhysChem 2009, 10, 1922-1926.
[44] J. Solla-Gullón, P. Rodríguez, E. Herrero, A. Aldaz and J. M. Feliu, ''Surface characterization of platinum electrodes'' Physical Chemistry Chemical Physics 2008, 10, 1359-1373.
[45] Z. Y. Zhou, N. Tian, Z. Z. Huang, D. J. Chen and S. G. Sun, ''Nanoparticle catalysts with high energy surfaces and enhanced activity synthesized by electrochemical method'' Faraday Discussions 2008, 140, 81-92.
[46] E. Herrero, V. Climent and J. M. Feliu, ''On the different adsorption behavior of bismuth, sulfur, selenium and tellurium on a Pt(775) stepped surface'' Electrochemistry Communications 2000, 2, 636-640.
[47] J. Clavilier, J. P. Ganon and M. Petit, ''A comparative study of the underpotential deposition of two monovalent cations, Tl+ and H+, on Pt (111) as a way to the interpretation of the unusual adsorption states'' Journal of Electroanalytical Chemistry 1989, 265, 231-245.
[48] R. R. Adzic, J. X. Wang, O. M. Magnussen and B. M. Ocko, ''Structure of Tl adlayers on the Pt(111) electrode surface: Effects of solution pH and bisulfate coadsorption'' Journal of Physical Chemistry 1996, 100, 14721-14725.
[49] C. Busó-Rogero, V. Grozovski, F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero and J. M. Feliu, ''Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles'' Journal of Materials Chemistry A 2013, 1, 7068-7076.
[50] D. K. Lambert, ''Vibrational Stark effect of adsorbates at electrochemical interfaces'' Electrochimica Acta 1996, 41, 623-630.
Capítulo 7: Nanopartículas de platino de forma controlada modificada
con adátomos para la oxidación de etanol
223
Capítulo 7: Nanopartículas de platino de forma
controlada modificada con adátomos para la oxidación de
etanol
RESUMEN
El actual capítulo trata de encontrar algún catalizador bimetálico capaz de mejorar la
actividad en la oxidación de etanol, intentando beneficiar la formación de CO2 en
detrimento de la producción de ácido acético. Estos catalizadores son preparados a partir
de nanopartículas de platino a las cuales se le adsorbe algún átomo de un metal diferente
(Sn, Rh, Ru o Pb). La reactividad de las superficies modificadas para la oxidación de
etanol se estudia en medios ácido y alcalino, específicamente en 0.5 M H2SO4 y 0.1 M
NaOH, empleando las mismas muestras que en el capítulo 6, esto es, la (100)Pt y la
(111)Pt con el correspondiente átomo adsorbido.
La adsorción de los metales sobre las nanopartículas de platino se realiza utilizando
disoluciones diluidas (10-5-10-6 M) de los metales precursores, concretamente SnSO4,
RhCl3, RuCl3 y Pb(NO3)2 en 0.5 M H2SO4. Las bajas concentraciones de precursor
metálico permiten un depósito lento sobre las superficies de platino, el cual se controla
mediante una voltametría cíclica en H2SO4. El recubrimiento metálico se calcula mediante
la disminución de la carga de adsorción de hidrógeno característica del platino en el caso
del Sn, el Ru y el Pb, denotándose también como recubrimiento máximo cuando han
desaparecido los picos de adsorción de hidrógeno del Pt al igual que en el caso del capítulo
6. Sin embargo, en el caso del Rh, esa zona de adsorción de hidrógeno se solapa con la del
platino, por lo que no es adecuado usar este método para calcular el recubrimiento. En este
caso, se indica únicamente el incremento de la cantidad de Rh.
Al estudiar la oxidación de 0.2 M CH3CH2OH en medio 0.5 M H2SO4, la adsorción
de Rh sobre Pt ejerce un efecto negativo para la oxidación de etanol, mientras que las
Capítulo 7: Nanopartículas de platino de forma controlada modificada con adátomos para la oxidación de etanol
224
superficies modificadas Pt-Ru y Pt-Pb muestran ligeras mejoras. El Ru provoca un avance
en los potenciales a los cuales se inicia la reacción de oxidación, sobre todo en el caso de la
muestra (100)Pt, revelando la catálisis para la oxidación del CO adsorbido hasta CO2, pero
mostrando también un decrecimiento de las corrientes totales de oxidación, indicativo de
una disminución en la eficiencia respecto a las nanopartículas de platino sin modificar,
sobre todo para la formación de ácido acético. El Pb mejora ligeramente la actividad en la
oxidación de etanol, pero sin alterar drásticamente la distribución de productos, como se
observa en la poca alteración en la forma de las voltametrías cíclicas.
No obstante, de todos los adátomos estudiados en medio ácido, el más efectivo es el
Sn, como así indican las voltametrías cíclicas de la Fig. 7.3 y la Fig. 7.4. En este caso, el
potencial al cual se inicia la oxidación de etanol se desplaza hacia valores más negativos
independientemente de la muestra usada, ya sea (100)Pt o (111)Pt. Este comportamiento se
puede explicar mediante el denominado mecanismo bifuncional, donde moléculas OH
adsorbidas sobre los átomos de Sn favorecen la catálisis CO/CO2. El efecto del Sn sobre
las dos muestras es diferente dependiendo del potencial al cual se encuentre: a bajos
potenciales (hasta 0.6 V), se produce la mencionada catálisis del CO hasta CO2, mientras
que a potenciales más elevados se mejora la oxidación incompleta hasta ácido acético.
Además, resultados de cronoamperometría investigan la estabilidad con el tiempo de estas
superficies modificadas, asignando la caída de corriente al CO adsorbido durante la
reacción de oxidación de etanol. En el caso de la muestra (100)Pt, la actividad disminuye a
recubrimientos más bajos que en el caso de la muestra (111)Pt, debido al efecto
competitivo del Sn sobre las nanopartículas de platino para la oxidación del CO adsorbido
o la formación de ácido acético dependiendo del potencial.
En el caso de las superficies modificadas en medio alcalino 0.1 M NaOH, se efectúan
estudios exclusivamente de voltametría cíclica, prestando únicamente atención a los
potenciales de inicio de la oxidación de etanol, más interesantes desde un punto de vista
práctico como el de las pilas de combustible. Además, a potenciales elevados las corrientes
observadas están fuertemente afectadas por la caída óhmica, otra razón por la que no es
posible una correcta comparación entre los diferentes catalizadores. Como se deduce del
capítulo 4 de la tesis, el mecanismo de reacción a este pH es totalmente diferente,
formando casi exclusivamente acetato. Por ello, átomos como el Ru no ejercen ningún
Resumen
225
efecto positivo ya que no catalizan la reacción del CO a CO2, la cual necesita la rotura del
enlace C-C. Sn, Rh y Pb favorecen mínimamente la oxidación de etanol en este medio,
debido de nuevo a la adsorción de OH sobre estos átomos, siguiendo el mismo mecanismo
bifuncional pero en este caso solo para la formación de ácido acético (acetato en
condiciones de pHs alcalinos), al contrario de lo que ocurre en el medio ácido.
227
Chapter 7
This chapter has been adapted and formatted from Electrochimica Acta 2016, 196, 270-279.
Corresponding author: [email protected]
Chapter 7: Adatom modified shape-controlled platinum nanoparticles towards ethanol oxidation
228
7.1 Introduction
Nowadays, the studies about new energy sources are gaining momentum due to the
depletion of fossil fuels. One of these alternative energy sources is the development of fuel
cells, which can obtain energy simply from the reaction between a fuel and an oxidant
species (usually oxygen). Fundamental research in fuel cells is usually centered in the
material used for manufacturing the catalyst and its electrocatalytic response to the desired
reaction on the cathode or on the anode [1]. As a catalyst, platinum is a good choice due to
its well-known catalytic properties. Different chemicals have been selected as possible
candidates for using as a fuel in the anode, from the most typical hydrogen to some small
organic molecules such as formic acid, methanol or ethanol. Among these organic
molecules, ethanol is one of the most studied fuels [2], because it presents some
advantages as the easiness for obtaining it from biomass in addition to its low toxicity or its
high energy density for the complete oxidation to CO2, where 12 electrons are exchanged
according with the reaction:
(7.1)
Nevertheless, this reaction is not as simple as appears in the general equation
presented above, because parallel reactions can occur, decreasing the efficiency of the
complete oxidation, the desired route. When using platinum as catalyst, this reaction has
shown to be structure sensitive [3], that is, depending on the arrangement of the platinum
atoms on the surface of the electrode, the reactivity changes. On this electrode, ethanol
oxidation mechanism has a dual-path mechanism:
(7.2)
Step (1) of the scheme corresponds to the ethanol oxidation to acetaldehyde, whereas step
(2) is the acetaldehyde oxidation to acetic acid. These two reactions compose the route
known as ethanol incomplete oxidation. Step (3) and step (4) show the C-C bond scission
from acetaldehyde and ethanol respectively, needed to achieve CO2 formation. However,
Introduction
229
previous to the complete oxidation, CO is formed and poisons the catalyst surface. At high
potentials, this CO is finally oxidized to CO2. On Pt(111) electrodes, only acetic acid is
formed without poison formation. However, on Pt(100) and Pt(110) electrodes, C-C bond
scission is observed and CO is formed, blocking the surface for further reaction at low
potentials [3, 4]. On the other hand, the oxidation in alkaline solutions leads to the almost
exclusive production of acetate and negligible amounts of CO and CO2 (carbonate at
higher pH values) [5].
The problem of using platinum is its high price. One option for reducing the cost of
platinum is to use it in the form of nanoparticles, with high active area, thus allowing the
use of lower amounts of platinum. In addition, most of the reactions in fuel cell
applications are structure sensitive. Thus, a careful selection of the surface structure of the
nanoparticle can lead to an increase in the electrocatalysis. This can be achieved by
synthesizing shape-controlled platinum nanoparticles, as has been done for the oxidation of
interesting molecules (formic acid, methanol, ethanol, glycerol and ammonia [6-9]) or
oxygen reduction [10-12]. An additional increase in the catalytic activity of the Pt can be
obtained by the modification of the electronic properties by forming alloys.
Focusing on ethanol oxidation, alloys composed of platinum and other metals, such
as Sn, Ru, Rh, Mo or Cu, show improved selectivity to the C-C bond scission and/or
enhanced activity for the oxidation of CO, so that the total electrocatalytic activity is
increased [13-19]. However, for a better understanding of the actuation mechanism of the
additional element in the Pt alloys, the controlled deposition of foreign adatoms on
platinum with a well-known surface structure is considered as a suitable approach for this
study. With this approach, a large amount of different modified platinum surfaces can be
tested due to the easiness of preparation of electrodes with variable composition [20].
Additionally, the test of the different modifications can be carried out in similar conditions,
which allows a better comparison between different modifiers.
The metals chosen for depositing on Pt surface and study their electrocatalytic effect
towards ethanol oxidation were tin, rhodium, ruthenium and lead. In previous studies, Sn
and Ru deposition on stepped surfaces showed some enhancement for the oxidation to CO2
[21, 22], whereas Pt deposited on Rh electrodes also shows increased activity for the C-C
Chapter 7: Adatom modified shape-controlled platinum nanoparticles towards ethanol oxidation
230
bond scission [23]. In addition, some works have demonstrated the improvement in the
carbonate formation when Pb atoms are adsorbed on polycrystalline Pt surfaces in alkaline
solutions [24, 25].
In this work, fundamental studies about the electroactivity of the Sn, Rh, Ru and Pb-
modified platinum nanoparticles, specifically in (100) and (111)Pt nanoparticles, for
ethanol oxidation are reported in two different pH values (acidic and alkaline solutions).
These two types of nanoparticles have been selected because they represent two different
paradigms for the ethanol oxidation reaction. As aforementioned, the (111) plane of Pt is
inactive for the cleavage of the C-C bond, yielding acetic acid/acetate both in acid and
alkaline solutions, whereas the (100) plane is active for this process in acidic conditions.
Thus, the effect of the adatoms on both reaction paths can be analyzed. The studies will be
carried out using voltammetric and chronoamperometric techniques, which will allow the
best conditions to achieve the highest electrocatalytic activity (pH and composition) to be
determined for the studied reaction.
Experimental
231
7.2 Experimental
Preferential cubic and octahedral Pt nanoparticles were used in this study. According
to the observed shape by TEM, these nanoparticles should contain a high fraction of (100)
and (111) domains, respectively [6, 26]. For that reason, they have been named (100)Pt
nanoparticles and (111)Pt nanoparticles. These Pt nanoparticles were prepared according to
the colloidal method [27]. In brief, solutions containing K2PtCl4 for (100) nanoparticles
and H2PtCl6 for (111)Pt nanoparticles were reduced using H2 in controlled conditions to
form nanoparticles. After that, nanoparticles were cleaned with NaOH pellets and
dispersed in water. Additional details on the synthesis can be found in ref. [7, 26].
Pt nanoparticles were deposited on a glassy carbon support, and dried during 15-20
minutes in Ar atmosphere. After the drying, Pt nanoparticle samples were cleaned using
CO adsorption and stripping, but avoiding the use of high potential values to preserve the
surface structure order. Cyclic voltammetry was used to assure the correct cleaning of the
platinum nanoparticles. The active area was measured from the hydrogen adsorption
charge after double layer subtraction using the reported reference value of 0.23 mC cm-2
[28].
The deposition of Sn, Rh, Ru, and Pb on the nanoparticles was carried out from
solutions containing SnSO4 (Merck®), hydrated RhCl3 (Aldrich®), hydrated RuCl3 (Fluka®)
and Pb(NO3)2 (Aldrich®), all of them with a purity higher than 99.8%. A very low
concentration of the metal precursor was used (10-5-10-6 M in 0.5 M H2SO4), so that the
deposition of the metal is slow and diffusion controlled. This allows the change of the
adatom coverage on the surface to be followed by using the cyclic voltammogram recorded
between 0.06 and 0.8 V at 0.05 V s-1. The increase in the adatom coverage leads to the
decrease in the hydrogen adsorption charge, as shown in previous experiments with Pd, Sb,
Bi or Tl [29-32]. Thus, the coverage can be determined using the following expression:
0
01x
H Hx H
H
q qq
θ θ −= − =
(7.3)
Chapter 7: Adatom modified shape-controlled platinum nanoparticles towards ethanol oxidation
232
where qH0 and qH
x are the hydrogen adsorption charges for bare and adatom modified Pt
nanoparticles. This method for measuring the adatom coverage is valid for all the metals
used in this work except for Rh, where new peaks appear in the voltammetric profile in the
hydrogen adsorption region, due to hydrogen adsorption on rhodium. This prevents an
accurate determination of the Rh coverage and for that reason an increasing order of
coverage is only indicated.
Once completed the preparation of the modified electrodes, a cyclic voltammogram
or a chronoamperogram were recorded in 0.2 M CH3CH2OH in 0.5 M H2SO4 or 0.1 M
NaOH as supporting electrolyte, depending on the desired pH conditions. Ethanol absolute
(Merck® p.a.), H2SO4 (Merck® Suprapur 96%) and NaOH monohydrate (99.99%, Merck®
Suprapur) were used for preparing the solutions together with ultrapure water (Elga
Purelab Ultra 18.2 MΩ cm).
All the experiments were carried out at room temperature in a three-cell
electrochemical cell, using a Pt wire as a counter-electrode, and reversible hydrogen (N50,
Air Liquide) as reference electrode (RHE). Ar (N50, Air Liquide) was employed for
deoxygenating the solutions. Cyclic voltammetry and chronoamperometric experiments
were performed using a waveform generator (EG&EG PARC 175), together with a
potentiostat (eDAQ EA161) and a digital recorder (eDAQ ED401).
Results and discussion
233
7.3 Results and discussion
7.3.1 Electrochemical characterization of modified Pt nanoparticles
Previous to the ethanol oxidation studies, a cyclic voltammogram is recorded to
characterize the Pt nanoparticles samples in 0.5 M H2SO4. This voltammogram is
considered as a fingerprint of the Pt surfaces and allows the characterization of the
different domains present on the nanoparticle samples. This electrochemical
characterization is presented in Fig. 7.1 and Fig. 7.2 (Θ=0). Very briefly, the (111)
nanoparticles show a wave due to the adsorption of sulfate on the (111) domains between
0.45 and 0.6 V, whereas the adsorption processes on the (100) ordered domains produces a
defined signal at ca. 0.37 V. Additionally, monodimensional domains such as edges, steps
or defects with (110) and (100) symmetry appear as peaks at 0.125 and 0.26 V,
respectively. A more exhaustive description of the voltammetric profiles of these shape-
controlled Pt nanoparticles can be found in references [26, 33].
Fig. 7.1. Voltammetric profiles for different adatoms and coverages in (100)Pt nanoparticles. Test
solution: 0.5 M H2SO4. Scan rate: 0.05 V s-1.
-0.15
-0.10
-0.05
0.00
0.05
0.10
0.0 0.2 0.4 0.6 0.8 0.0 0.2 0.4 0.6 0.8
-0.15
-0.10
-0.05
0.00
0.05
0.10
0.0 0.2 0.4 0.6 0.8
-0.15
-0.10
-0.05
0.00
0.05
0.10
0.0 0.2 0.4 0.6 0.8
-0.15
-0.10
-0.05
0.00
0.05
0.10 Ru
Rh
j/mA
cm-2
E vs RHE/V
j/mA
cm-2
θ=0 θ=0.26 θ=0.51 θ maximum
Sn
E vs RHE/V
θ0
θ1
θ2
θ maximum
j/mA
cm-2
j/mA
cm-2
E vs RHE/V
θ=0 θ=0.18 θ=0.46 θ maximum
Pb
E vs RHE/V
θ=0 θ=0.24 θ=0.46 θ maximum
Chapter 7: Adatom modified shape-controlled platinum nanoparticles towards ethanol oxidation
234
Fig. 7.2. Voltammetric profiles for (111)Pt nanoparticles modified by different adatoms in 0.5 M
H2SO4 at 0.05 V s-1.
The changes of the profiles upon the adsorption of the different adatoms have been
also followed using voltammetry. Fig. 7.1 and Fig. 7.2 show the evolution of the
voltammetric profile for both Pt nanoparticle samples after being modified by Sn, Rh, Ru
and Pb in 0.5 M H2SO4. For Sn, the first stage in the deposition is the adsorption on
monodimensional domains as can be observed by the diminution of the peaks associated
with those sites, whereas the (111) ordered domains are only covered at high adatom
coverages. This behavior is in agreement with previous experimental and theoretical results
using stepped (111) surfaces for tin [21, 34-36] or for other adatoms with lower
electronegativity values than Pt [37, 38]. In addition, an irreversible redox process was
observed around 0.6-0.7 V, assigned to the surface oxidation at tin atoms. The same feature
is clearly observed for Sn-modified Pt nanoparticles with high adatom coverage in this
range of potential. No additional peaks due to the adsorption of tin can be observed
between 0.1 and 0.4 V, which allow the coverage to be determined by the decrease of the
hydrogen adsorption charge.
-0.15
-0.10
-0.05
0.00
0.05
0.10
0.15
0.200.0 0.2 0.4 0.6 0.8 0.0 0.2 0.4 0.6 0.8
-0.15
-0.10
-0.05
0.00
0.05
0.10
0.15
0.20
0.0 0.2 0.4 0.6 0.8
-0.15
-0.10
-0.05
0.00
0.05
0.10
0.15
0.0 0.2 0.4 0.6 0.8
-0.15
-0.10
-0.05
0.00
0.05
0.10
0.15
E vs RHE/VE vs RHE/V
j/mA
cm-2
θ=0 θ=0.27 θ=0.53 θ maximum
Sn Rh
Ru Pb
j/mA
cm-2
j/mA
cm-2
θ0
θ1
θ2
θmax
j/mA
cm-2
E vs RHE/V
θ=0 θ=0.19 θ=0.31 θ maximum
E vs RHE/V
θ=0 θ=0.29 θ=0.49 θ maximum
Results and discussion
235
When Rh is adsorbed on the Pt surface, the voltammetric profiles progressively
evolve until the typical features of Rh in this medium appear [39]. Thus, the hydrogen
adsorption region shifts to negative potential values and the onset for oxide formation takes
place at lower potential values. For the Rh-modified (111)Pt nanoparticles, Fig. 7.2, two
irreversible peaks can be seen at 0.16 V and 0.13 V, also observed in Rh/Pt (111) [40, 41].
The Rh adsorption produces an overlapping between the two hydrogen adsorption regions
in Pt and Rh, preventing an accurate determination of the Rh coverage. For this reason, as
it is mentioned above, specific coverage values for these modified electrodes are not given,
being simply ordered in increasing coverage values.
For Ru adsorption on the Pt nanoparticles, the behavior is similar to the Sn
deposition, thus allowing an easy follow up of the Ru coverage with the decrease of
hydrogen adsorption peaks [22, 42, 43]. Some additional Ru adsorption characteristics for
sulfuric acid solutions appear in Fig. 7.1, as the small peak at 0.22 V assigned to the sulfate
adsorption on large-ordered (100) domains close to Ru atoms, in addition to the current
increase from 0.6 V due to the Ru oxidation, which takes place at high potentials.
Finally, Pb adsorption on Pt surfaces is not very stable, and the adatom can be
desorbed only with a few cycles at relative low potentials [44]. Thus, high coverage values
cannot be achieved. However, no additional peaks are observed due to Pb redox processes
at lower potentials, so the usual method of the decrease in hydrogen adsorption charge can
be used to follow the Pb coverage. The voltammetric curves are similar to others reported
to Pb adsorption on polycrystalline surfaces [25], observing also an increase in the current
around 0.6 V due to the OH adsorption on Pb atoms.
7.3.2 Ethanol oxidation in acidic medium
Fig. 7.3 shows the voltammetric profiles for ethanol oxidation on bare and adatom
decorated (100)Pt nanoparticles. For the bare nanoparticles, the prominent peak at 0.8 V is
due to the oxidation of CO layer from the C-C bond cleavage of ethanol, more favorable in
(100) ordered domains, and the subsequent activation of the surface for the direct oxidation
Chapter 7: Adatom modified shape-controlled platinum nanoparticles towards ethanol oxidation
236
to acetic acid and to CO2 [7]. This fact leads to a large hysteresis between the positive and
negative scan directions. Thus, in the negative scan direction, larger currents are observed,
due to the absence of CO accumulation on the surface below 0.5 V, which allows the
oxidation of ethanol on the surface. On the other hand, Fig. 7.4 displays the voltammetric
response for (111)Pt nanoparticles. As can be seen, the hysteresis is very low, due to the
preference of the (111) ordered domains for the incomplete oxidation of ethanol to acetic
acid [3].
Fig. 7.3. Voltammetric profiles for (100)Pt nanoparticles modified by Sn, Rh, Ru and Pb in 0.2 M
ethanol + 0.5 M H2SO4 at 0.02 V s-1. Inset: Currents for positive scan direction in the onset potential region.
Small differences in the voltammograms recorded in the absence of the adatoms for
the same type of nanoparticles are observed, especially regarding the maximum current
density. These effects are due to changes in the spatial distribution of the deposit. Although
the amount of nanoparticles is similar in all cases, some agglomeration of the nanoparticles
may take place during the drying process. As has been shown [45], nanoparticle
agglomeration leads to deposits in which some nanoparticles are not active for the
oxidation since the incoming flux of ethanol is consumed in the outer layers of the deposit,
0.0
0.5
1.0
1.50.0 0.2 0.4 0.6 0.8 0.0 0.2 0.4 0.6 0.8 1.0
0.0
0.5
1.0
1.5
0.0 0.2 0.4 0.6 0.80.0
0.5
1.0
1.5
0.0 0.2 0.4 0.6 0.8 1.00.0
0.5
1.0
1.5
E vs RHE/V
j/mA
cm-2
θ=0 θ=0.27 θ=0.50 θ maximum
Sn Rh
j/m
A cm
-2
E vs RHE/V
θ0
θ1
θ2
θ maximum
Ru
j/mA
cm-2
E vs RHE/V
θ=0 θ=0.27 θ=0.47 θ maximum
Pb
j/m
A cm
-2
E vs RHE/V
θ=0 θ=0.27 θ=0.38 θ maximum
0.25 0.30 0.35 0.400.0
0.1
0.2
0.25 0.30 0.35 0.400.0
0.1
0.2
0.25 0.30 0.35 0.400.0
0.1
0.2
0.25 0.30 0.35 0.400.0
0.1
0.2
Results and discussion
237
leading to lower current densities than the reported previously [7]. Since the main objective
of the manuscript is to understand the role of the adatoms in the oxidation mechanism, the
voltammograms for the different coverages for a given adatom were recorded with the
same sample, so that currents can be compared and the different effects of the adatoms can
be rationalized.
Fig. 7.4. Voltammetric profiles for ethanol oxidation on (111)Pt nanoparticles modified by Sn, Rh, Ru
and Pb in 0.2 M ethanol + 0.5 M H2SO4. Scan rate: 0.02 V s-1. Inset: Currents for positive scan direction in
the onset potential region.
Among all the tested adatoms, the one that has a clear negative impact in the
oxidation of ethanol is Rh. In all cases, the current diminishes significantly and no change
in the onset potential can be detected. Although it has been reported that PtRh alloys
increase the CO2/acetaldehyde ratio in ethanol oxidation [15, 23], the net effect observed
here is a diminution of the total current. At this respect, it is worth noting that Rh atoms are
exclusively adsorbed at the surface of Pt nanoparticles, that is, Rh decorated Pt surface is
formed, whose behavior can be different from that observed for a PtRh surface alloy.
Although it has been proposed that RhPt alloys catalyze the C-C bond splitting [15], there
is not a significant increase in the total currents. This is probably due to the low activity of
0.0
0.5
1.0
1.50.0 0.2 0.4 0.6 0.8 0.0 0.2 0.4 0.6 0.8 1.0
0.0
0.5
1.0
0.0 0.2 0.4 0.6 0.80.0
0.5
1.0
1.5
0.0 0.2 0.4 0.6 0.8 1.0
0.0
0.5
1.0
E vs RHE/V
j/mA
cm-2
θ=0 θ=0.25 θ=0.57 θ maximum
Sn Rh
j/m
A cm
-2
E vs RHE/V
θ0
θ1
θ2
θ maximum
Ru
j/mA
cm-2
E vs RHE/V
θ=0 θ=0.19 θ=0.27 θ=0.39
Pb
j/m
A cm
-2
E vs RHE/V
θ=0 θ=0.31 θ=0.56 θ maximum
0.25 0.30 0.35 0.40 0.450.0
0.1
0.2
0.25 0.30 0.35 0.40 0.45
0.0
0.1
0.2
0.25 0.30 0.35 0.40 0.450.0
0.1
0.2
0.25 0.30 0.35 0.40 0.450.0
0.1
0.2
Chapter 7: Adatom modified shape-controlled platinum nanoparticles towards ethanol oxidation
238
the Rh atoms for the dehydrogenation of small organic molecules. The net result of Rh is a
diminution of the total current, because the increase in the C-C bond splitting rate does not
compensate the diminution of the rate in the other steps of the reaction. Finally, for the
highest coverage, the curves resemble those obtained in pure Rh electrodes [46], that are
known to be much less active than Pt for ethanol electrooxidation.
Ruthenium on platinum surfaces is known to catalyze the oxidation of CO which
appears as intermediate on oxidation processes of small organic molecules. For that reason,
previous results for ethanol oxidation on Pt stepped surfaces [22, 47] and for methanol
oxidation in platinum surfaces [43, 48] show the improvement of the electrocatalytic
activity. In the case of ethanol, Ru is not affecting other steps in the reaction, that is, is not
enhancing the C-C bond cleavage or the formation of acetic acid as has been shown with
single crystal electrodes [22]. Thus, for the (100)Pt nanoparticles, a lower potential onset
for ethanol oxidation is observed in Fig. 7.3, since Ru catalyzes the oxidation of CO
formed at low potential values. For the (111)Pt nanoparticles, since the activity for the C-C
bond cleavage is low, the onset does not change significantly. It should be stressed that the
observed effects of Ru deposition for the nanoparticles are smaller than those recorded for
the Ru decorated stepped surfaces. In this latter case, the Ru adatoms are deposited
neighboring the sites active for the C-C bond cleavage, so that, their activity is maximized.
For the nanoparticles, such control is not possible, and thus its effect is lower.
Additionally, the progressive current decrease with increasing coverages indicates a
negligible activity of the other steps in the reaction and the poor catalytic behavior for
these surfaces.
The deposition of Pb on Pt surfaces in acidic solutions improves the onset potential
for formic acid oxidation [49, 50]. In the case of ethanol, a small increase in the currents is
observed for low and intermediate coverages. Additionally, the shape of the
voltammogram remains almost unaffected by the presence of lead on the surface of the
nanoparticles. This fact means that lead on the Pt surface catalyzes the oxidation of ethanol
but it does not change significantly the product distribution. Additionally, the huge current
decay with the other adatoms at the maximum coverage is not observed for lead because of
the poor stability of these surfaces [44], that prevent higher coverages for the Pb-modified
Pt nanoparticles.
Results and discussion
239
Clearly, the most significant catalytic effects for ethanol oxidation are observed for
the Sn modified nanoparticles. For low and medium Sn coverages, the onset potential for
ethanol oxidation is shifted to negative values, independently of the platinum nanoparticle
samples used. This current increase at low potentials is related to the catalysis of the CO
adsorbed to CO2, as it is confirmed with the disappearance of the prominent peak in the
(100)Pt nanoparticles characteristic of the CO presence. This fact can be understood with
the bifunctional mechanism [21, 51], where the catalysis CO/CO2 is enhanced with OH
adsorbed on Sn atoms. Nevertheless, for (100)Pt nanoparticles the onset potential seems to
be unaltered for coverage values above 0.3, whereas in (111)Pt nanoparticles (Fig. 7.4)
continuously decreases for increasing coverages. This effect can be explained by the
competitive adsorption between CO and tin atoms, which produces a decrease in the free
sites where ethanol oxidation occurs. For this reason, mainly for (100)Pt nanoparticles, the
catalytic effect of Sn remains constant after coverages of 0.3, whereas in (111)Pt
nanoparticles sample, where the CO formation rate is significantly lower, the onset
potential for ethanol oxidation still diminishes for high adatom coverages. In addition, for
this sample, the increase in the total currents and the diminution of the hysteresis confirms
that the presence of tin adsorbed on (111) ordered domains catalyzed the incomplete
ethanol oxidation to acetic acid [21]. At maximum coverage, activity decays drastically
due to the absence of free sites necessary for catalyzing the ethanol oxidation reaction.
Since tin is the most active adatom in the catalysis, it is important to deepen in the
understanding of its effects in the reaction. In Fig. 7.5, the ratio of the currents recorded in
the positive going-sweep between the modified nanoparticles with the highest activity
(coverage close to 0.5) and the unmodified nanoparticles is shown. Two regions can be
observed in these curves, especially for the (111)Pt nanoparticles. At low potentials, the
increase is due to the catalysis of CO oxidation. In this region, the improvement factor is
slightly better in (111)Pt nanoparticles, probably due to a small increase in the production
of CO or the catalysis of the oxidation for the CH3 fragment on the free Pt sites. On the
(100)Pt nanoparticles, this latter process is less possible because the CO coverage is
higher. At higher potentials (above 0.75 V), when all the adsorbed CO molecules have
been effectively oxidized to CO2, the currents of the modified and unmodified samples
become essentially similar independently of the Pt nanoparticles used.
Chapter 7: Adatom modified shape-controlled platinum nanoparticles towards ethanol oxidation
240
Fig. 7.5. Ratio between ethanol oxidation current densities obtained for the bare and Sn-decorated
(coverage around 0.5) shape-controlled platinum nanoparticles in the positive scan direction. Data taken from
the tin experiments of Figs. 7.3 and 7.4.
Chronoamperometric results are presented in Fig. 7.6 for evaluating the variance of
the activity and assure the stability of the modified electrodes with time. In this
experiment, after a step to 0.9 V for oxidizing the CO formed at low potentials, the
potential is set at 0.6 V to record the evolution of the oxidation currents. In all cases, a
significant decay in the currents is measured after 10 min. This decay should be due to the
accumulation of CO on the surface, because the rate of the C-C bond cleavage step is
higher than the CO oxidation rate.
Fig. 7.6. Chronoamperometric response at 0.6 V for 0.2 M ethanol + 0.5 M H2SO4 in: a) (100)Pt and
b) (111)Pt nanoparticles modified with different coverages of Sn.
0.2 0.4 0.6 0.8 1.00.5
1.0
1.5
2.0
2.5
3.0
3.5
j θ Sn=0
.5 /jba
re
E vs RHE/V
(100) Pt nanoparticles (111) Pt nanoparticles
0 100 200 300 400 500 600 7000.0
0.5
1.0
1.5
2.0
2.5
3.0
0 100 200 300 400 500 600 7000.0
0.5
1.0
1.5
2.0
2.5
3.0
a) b)
t/s
θSn=0 θSn=0.24 θSn=0.44 θSn=maximum
j/mA
cm-2
t/s
θSn=0 θSn=0.38 θSn=0.50 θSn=maximum
Results and discussion
241
Comparing (100) and (111)Pt nanoparticles, the increase of the currents after 10 min
with respect to those recorded in absence of tin is higher for the (111)Pt nanoparticles. This
effect can be easily explained by the higher activity for the C-C bond splitting of the
(100)Pt nanoparticles. Thus, the stationary CO coverage will be higher, that is, there are
less free Pt sites, and consequently lower currents are recorded at long times. For the
(111)Pt nanoparticles, the higher number of free Pt available sites and the catalytic effect
of tin for the oxidation of ethanol to acetic acid results in higher currents [21].
The currents at 600 s of the chronoamperometric curves vs. tin coverage are plotted
in Fig. 7.7 for the two Pt nanoparticles samples used. Initially, currents increase with the
addition of tin on the surface. For (100)Pt nanoparticles, at coverage values higher than
0.3, it diminishes, whereas for the (111)Pt nanoparticles, it reaches the maximum and
stable value for coverages above 0.5. At higher tin coverages, currents increase but very
slightly. Again, the competitive catalytic effect of tin for oxidation of CO and the oxidation
of ethanol to acetic acid explains this behavior.
Fig. 7.7. Current densities measured after 600 s in Fig. 7.6 vs tin coverage for Sn-decorated shape-
controlled Pt nanoparticles.
0.0 0.2 0.4 Max.0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
0.55
0.60
j 600
s / m
A cm
-2
θSn
(100) Pt nanoparticles (111) Pt nanoparticles
Chapter 7: Adatom modified shape-controlled platinum nanoparticles towards ethanol oxidation
242
7.3.3 Ethanol oxidation in alkaline solutions.
Similarly to that shown in Fig. 7.3 and 7.4, the study of the effect of the adatoms
towards the oxidation of ethanol in alkaline conditions is shown in Figs. 7.8 and 7.9. Due
to the high activity above 0.7 V, the voltammograms are affected by the diffusion of the
electroactive species through the catalyst layers and also by ohmic drop, due to the large
currents and the lower conductivity of the alkaline solutions [5, 45]. However, for practical
applications, currents above 0.7 V are not interesting, since the voltage obtained in a fuel
cell would be negligible. For that reason, only onset potentials will be analyzed in this
case.
Fig. 7.8. Voltammetric profiles for ethanol oxidation on (100)Pt nanoparticles modified by Sn, Rh, Ru
and Pb in 0.2 M ethanol + 0.1 M NaOH. Scan rate: 0.02 V s-1. Inset: Currents for positive scan direction in
the onset potential region.
It was shown before that the solution pH has a strong influence on the oxidation
mechanism, considerably modifying the ratio between the products formed after changing
from acidic to alkaline solutions [5, 52]. As previously mentioned, the main product in the
oxidation for the different Pt single crystal electrodes and nanoparticles is acetate, whereas
Results and discussion
243
the amount of carbonate detected can be considered negligible. This drastic change in the
oxidation mechanism has been related to changes in the adsorption modes of ethanol.
Thus, ethanol adsorption on platinum in alkaline media is proposed to occur through the
oxygen atom and not through the C1 atom of ethanol [52, 53]. Since the cleavage of the C-
C bond requires a bidentate adsorption mode with the C1 and C2 atoms bonded to the
surface, the adsorption through the oxygen atom hinders this process.
Fig. 7.9. Voltammetric profiles for ethanol oxidation on (111)Pt nanoparticles modified by Sn, Rh, Ru
and Pb in 0.2 M ethanol + 0.1 M NaOH. Scan rate: 0.02 V s-1. Inset: Currents for positive scan direction in
the onset potential region.
On the other hand, the oxidation to acetate requires the transfer of an OH group to
the C1 atom. In this medium, the results with single crystal electrodes show that ethanol
oxidation to acetic acid takes place when OH is adsorbed on the Pt surface. Thus, the main
product is acetate, and CO formation is quasi negligible in these conditions. This fact
determines the effect of the adatoms. Ru, which has high oxophilicity, could have
contributed to two different steps in the reaction mechanism: to the oxidation of CO to CO2
and to the oxidation of acetaldehyde to acetic acid/acetate, since both steps require the
Chapter 7: Adatom modified shape-controlled platinum nanoparticles towards ethanol oxidation
244
transfer of an oxygen group. As aforementioned, CO is not detected in alkaline solutions,
and therefore, this step cannot be catalyzed by Ru.
The complex nature of the oxidation process of Ru, yielding a mixture of hydroxides
and oxides, whose ratio depends on the electrode potential, prevents an effective catalytic
effect on this second step (acetaldehyde to acetate). In the positive scan direction and at
low potentials (inset of Fig. 7.8 and 7.9), the current is almost independent of the Ru
coverage. However, as the potential is increased, a significant diminution is observed. This
is probably due to a progressive transformation of Ru hydroxides to oxides, which are not
active for the catalysis. Since this process is irreversible, in the negative scan direction, the
currents at low potentials diminish with the Ru coverage. Consequently, Ru adatoms, the
role of which is the catalysis of the CO oxidation to CO2, do not show any enhancement
for the oxidation in alkaline conditions, acting almost as a pure third body for the reaction.
On the other hand, low Rh, Pb or Sn coverages show very small effects on the
oxidation of ethanol in this medium. As can be seen, the increase of the currents for low
coverages is small and the only net effect is a lower onset for low adatom coverages. At
higher coverages for those adatoms, total currents at any potential decrease. Previous
results for Pb deposited on polycrystalline platinum electrodes showed a significant
increase in the currents in alkaline solutions [24, 25]. In this case, a lower onset for the
oxidation is observed mainly for the (100)Pt nanoparticles. According with the references
cited, OH adsorption on Pb atoms takes place at potentials around 0.5-0.6 V, lower than on
platinum, allowing ethanol to be oxidized at more negative potentials. Thus, it can be
proposed that these adatoms act as a bifunctional catalyst by facilitating the transfer of the
OH to the adsorbed ethanol molecule, which compensates the lower amount of Pt free sites
due to the adatom coverage. However, the large increase previously observed with the Pt-
Pb combined surfaces is not achieved in these conditions, probably related with differences
in the deposition method and the low coverages reached due to the poor stability of Pb
adsorbed on Pt surfaces [44]. At higher coverages, current decreases, since the small
increase of the activity due to the deposition of the adatom does not compensate the loss of
the activity due to the blockage of platinum sites by the adatom.
Results and discussion
245
For Sn, which also has high oxophilicity, the observed behavior is better than that of
Ru, probably related to the different electrochemistry of the oxides/hydroxides. In this
case, the transfer of the OH takes place in the whole potential range, which results in
currents that are almost independent of the Sn coverage. This suggests that there is no
significant transformation of the hydroxides into oxides in this potential range, unlike what
is observed for Ru.
Chapter 7: Adatom modified shape-controlled platinum nanoparticles towards ethanol oxidation
246
7.4 Conclusions
The electrocatalytic properties of clean cubic and octahedral platinum nanoparticles
modified with Sn, Rh, Ru and Pb adatoms have been evaluated for ethanol oxidation
reaction in both acidic and alkaline media, using cyclic voltammetry and
chronoamperometry. The results indicate that, for the Sn-modified Pt nanoparticles, a clear
enhancement of both the onset potential and hysteresis is observed in acidic medium. In
addition, this enhancement is also dependent on the surface structure of the Pt
nanoparticles. The current increment at lower potentials for Sn-modified Pt nanoparticles
in acidic solutions is assigned to the catalysis of CO adsorbed to CO2 where Sn atoms
provide the OH needed to complete the oxidation. Interestingly, the (111)Pt nanoparticles
maintain the catalytic effect for higher coverages compared with (100)Pt nanoparticles
because of the lower competition with Sn atoms for the Pt free sites where takes place the
reaction. At higher coverages, both samples enhance the acetic acid formation. In similar
conditions, Ru-modified Pt nanoparticles only favors the oxidation of CO to CO2 at lower
potentials, without any effect for the C-C bond split or the acetic acid formation. Finally,
Pb-modified Pt modified surfaces improve slightly the ethanol oxidation but with the same
product distribution, whereas Rh adsorbed on Pt nanoparticles has a negative effect over
ethanol oxidation reaction.
In alkaline solutions, the main product in the oxidation is acetate, with negligible CO
formation. Thus, Ru atoms adsorbed on platinum nanoparticles, which major effect is to
catalyze the CO oxidation, does not affect ethanol oxidation in these conditions. However,
Sn, Rh and Pb-modified platinum nanoparticles show a very small improvement of the
potential onset. This effect is related to the OH adsorption on the adatom surfaces at lower
potentials, favoring ethanol oxidation to acetate by a bifunctional mechanism.
References
247
7.5 References
[1] M. T. M. Koper, ''Fuel Cell Catalysis: A Surface Science Approach'', Electrocatalysis and Electrochemistry A. Wieckowski (Ed.), John Wiley & Sons, Hoboken, New Jersey, 2009.
[2] E. Antolini, ''Catalysts for direct ethanol fuel cells'' Journal of Power Sources 2007, 170, 1-12.
[3] F. Colmati, G. Tremiliosi-Filho, E. R. Gonzalez, A. Berná, E. Herrero and J. M. Feliu, ''Surface structure effects on the electrochemical oxidation of ethanol on platinum single crystal electrodes'' Faraday Discussions 2008, 140, 379-397.
[4] F. Cases, M. López-Atalaya, J. L. Vázquez, A. Aldaz and J. Clavilier, ''Dissociative adsorption of ethanol on Pt (h, k, l) basal surfaces'' Journal of Electroanalytical Chemistry and Interfacial Electrochemistry 1990, 278, 433-440.
[5] C. Busó-Rogero, E. Herrero and J. M. Feliu, ''Ethanol Oxidation on Pt Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium'' ChemPhysChem 2014, 15, 2019-2028.
[6] J. Solla-Gullón, F. J. Vidal-Iglesias, A. López-Cudero, E. Garnier, J. M. Feliu and A. Aldaz, ''Shape-dependent electrocatalysis: methanol and formic acid electrooxidation on preferentially oriented Pt nanoparticles'' Physical Chemistry Chemical Physics 2008, 10, 3689-3698.
[7] C. Busó-Rogero, V. Grozovski, F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero and J. M. Feliu, ''Surface structure and anion effects in the oxidation of ethanol on platinum nanoparticles'' Journal of Materials Chemistry A 2013, 1, 7068-7076.
[8] J. Monzó, Y. Malewski, F. J. Vidal-Iglesias, J. Solla-Gullón and P. Rodríguez, ''Electrochemical Oxidation of Small Organic Molecules on Au Nanoparticles with Preferential Surface Orientation'' ChemElectroChem 2015, 2, 958-962.
[9] F. J. Vidal-Iglesias, J. Solla-Gullón, P. Rodríguez, E. Herrero, V. Montiel, J. M. Feliu and A. Aldaz, ''Shape-dependent electrocatalysis: ammonia oxidation on platinum nanoparticles with preferential (100) surfaces'' Electrochemistry Communications 2004, 6, 1080-1084.
[10] J. Hernández, J. Solla-Gullón, E. Herrero, J. M. Feliu and A. Aldaz, ''In Situ Surface Characterization and Oxygen Reduction Reaction on Shape-Controlled Gold Nanoparticles'' Journal of Nanoscience and Nanotechnology 2009, 9, 2256-2273.
[11] C. M. Sánchez-Sánchez, J. Solla-Gullón and V. Montiel, ''Electrocatalysis at nanoparticles'', in Electrochemistry: Volume 11 - Nanosystems Electrochemistry, The Royal Society of Chemistry, 2013, pp. 34-70.
[12] H. Erikson, A. Sarapuu, N. Alexeyeva, K. Tammeveski, J. Solla-Gullón and J. M. Feliu, ''Electrochemical reduction of oxygen on palladium nanocubes in acid and alkaline solutions'' Electrochimica Acta 2012, 59, 329-335.
[13] C. Lamy, S. Rousseau, E. M. Belgsir, C. Coutanceau and J. M. Léger, ''Recent progress in the direct ethanol fuel cell: development of new platinum-tin electrocatalysts'' Electrochimica Acta 2004, 49, 3901-3908.
[14] N. Fujiwara, K. A. Friedrich and U. Stimming, ''Ethanol oxidation on PtRu electrodes studied by differential electrochemical mass spectrometry'' Journal of Electroanalytical Chemistry 1999, 472, 120-125.
[15] J. P. I. de Souza, S. L. Queiroz, K. Bergamaski, E. R. Gonzalez and F. C. Nart, ''Electro-oxidation of ethanol on Pt, Rh, and PtRh electrodes. A study using DEMS and in-situ FTIR techniques'' Journal of Physical Chemistry B 2002, 106, 9825-9830.
[16] F. Colmati, E. Antolini and E. R. Gonzalez, ''Preparation, structural characterization and activity for ethanol oxidation of carbon supported ternary Pt-Sn-Rh catalysts'' Journal of Alloys and Compounds 2008, 456, 264-270.
[17] A. O. Neto, M. J. Giz, J. Perez, E. A. Ticianelli and E. R. Gonzalez, ''The electro-oxidation of ethanol on Pt-Ru and Pt-Mo particles supported on high-surface-area carbon'' Journal of the Electrochemical Society 2002, 149, A272-A279.
Chapter 7: Adatom modified shape-controlled platinum nanoparticles towards ethanol oxidation
248
[18] M. Ammam and E. B. Easton, ''PtCu/C and Pt(Cu)/C catalysts: Synthesis, characterization and catalytic activity towards ethanol electrooxidation'' Journal of Power Sources 2013, 222, 79-87.
[19] W. Zhou, Z. Zhou, S. Song, W. Li, G. Sun, P. Tsiakaras and Q. Xin, ''Pt based anode catalysts for direct ethanol fuel cells'' Applied Catalysis B: Environmental 2003, 46, 273-285.
[20] V. Climent, N. García-Aráez and J. M. Feliu, ''Clues for the Molecular-Level Understanding of Electrocatalysis on Single-Crystal Platinum Surfaces Modified by p-Block Adatoms'', in Fuel Cells Catalysis. A Surface Science Approach, M. T. M. Koper (Ed.) Wiley, Hoboken, New Jersey, 2009, pp. 209-244.
[21] V. Del Colle, J. Souza-Garcia, G. Tremiliosi-Filho, E. Herrero and J. M. Feliu, ''Electrochemical and spectroscopic studies of ethanol oxidation on Pt stepped surfaces modified by tin adatoms'' Physical Chemistry Chemical Physics 2011, 13, 12163-12172.
[22] V. Del Colle, A. Berná, G. Tremiliosi-Filho, E. Herrero and J. M. Feliu, ''Ethanol electrooxidation onto stepped surfaces modified by Ru deposition: electrochemical and spectroscopic studies'' Physical Chemistry Chemical Physics 2008, 10, 3766-3773.
[23] V. Del Colle, V. Grozovski, E. Herrero and J. M. Feliu, ''Unusually High Activity of Pt Islands on Rh(111) Electrodes for Ethanol Oxidation'' ChemCatChem 2013, 5, 1350-1353.
[24] Q. G. He, B. Shyam, K. Macounova, P. Krtil, D. Ramaker and S. Mukerjee, ''Dramatically Enhanced Cleavage of the C-C Bond Using an Electrocatalytically Coupled Reaction'' Journal of the American Chemical Society 2012, 134, 8655-8661.
[25] P. A. Christensen, S. W. M. Jones and A. Hamnett, ''An in situ FTIR spectroscopic study of the electrochemical oxidation of ethanol at a Pb-modified polycrystalline Pt electrode immersed in aqueous KOH'' Physical Chemistry Chemical Physics 2013, 15, 17268-17276.
[26] J. Solla-Gullón, P. Rodríguez, E. Herrero, A. Aldaz and J. M. Feliu, ''Surface characterization of platinum electrodes'' Physical Chemistry Chemical Physics 2008, 10, 1359-1373.
[27] T. S. Ahmadi, Z. L. Wang, T. C. Green, A. Henglein and M. A. El-Sayed, ''Shape-controlled synthesis of colloidal platinum nanoparticles'' Science 1996, 272, 1924-1926.
[28] Q. S. Chen, J. Solla-Gullón, S. G. Sun and J. M. Feliu, ''The potential of zero total charge of Pt nanoparticles and polycrystalline electrodes with different surface structure: The role of anion adsorption in fundamental electrocatalysis'' Electrochimica Acta 2010, 55, 7982-7994.
[29] F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero, A. Aldaz and J. M. Feliu, ''Pd Adatom Decorated (100) Preferentially Oriented Pt Nanoparticles for Formic Acid Electrooxidation'' Angewandte Chemie-International Edition 2010, 49, 6998-7001.
[30] F. J. Vidal-Iglesias, A. López-Cudero, J. Solla-Gullón and J. M. Feliu, ''Towards More Active and Stable Electrocatalysts for Formic Acid Electrooxidation: Antimony-Decorated Octahedral Platinum Nanoparticles'' Angewandte Chemie-International Edition 2013, 52, 964-967.
[31] A. Sáez, E. Expósito, J. Solla-Gullón, V. Montiel and A. Aldaz, ''Bismuth-modified carbon supported Pt nanoparticles as electrocatalysts for direct formic acid fuel cells'' Electrochimica Acta 2012, 63, 105-111.
[32] C. Busó-Rogero, J. V. Perales-Rondón, M. J. S. Farias, F. J. Vidal-Iglesias, J. Solla-Gullón, E. Herrero and J. M. Feliu, ''Formic acid electrooxidation on thallium-decorated shape-controlled platinum nanoparticles: an improvement in electrocatalytic activity'' Physical Chemistry Chemical Physics 2014, 16, 13616-13624.
[33] F. J. Vidal-Iglesias, R. M. Arán-Ais, J. Solla-Gullón, E. Herrero and J. M. Feliu, ''Electrochemical Characterization of Shape-Controlled Pt Nanoparticles in Different Supporting Electrolytes'' ACS Catalysis 2012, 2, 901-910.
[34] H. Massong, S. Tillmann, T. Langkau, E. A. A. Elmeguid and H. Baltruschat, ''On the Influence of Tin and Bismuth UPD on Pt(111) and Pt(332) on the Oxidation of CO'' Electrochimica Acta 1998, 44, 1379-1388.
References
249
[35] E. Mostafa, A. A. Abd-El-Latif, R. Ilsley, G. Attard and H. Baltruschat, ''Quantitative DEMS study of ethanol oxidation: effect of surface structure and Sn surface modification'' Physical Chemistry Chemical Physics 2012, 14, 16115-16129.
[36] G. Stalnionis, L. Tamasauskaite-Tamasiunaite, V. Pautieniene, A. Sudavicius and Z. Jusys, ''Modification of a Pt surface by spontaneous Sn deposition for electrocatalytic applications - 1. Catalyst preparation and characterization'' Journal of Solid State Electrochemistry 2004, 8, 892-899.
[37] E. Herrero, V. Climent and J. M. Feliu, ''On the different adsorption behavior of bismuth, sulfur, selenium and tellurium on a Pt(775) stepped surface'' Electrochemistry Communications 2000, 2, 636-640.
[38] A. Ferre-Vilaplana, R. Gisbert and E. Herrero, ''On the electrochemical properties of platinum stepped surfaces vicinal to the (100) pole. A computational study'' Electrochimica Acta 2014, 125, 666-673.
[39] D. A. J. Rand and R. Woods, ''A study of the dissolution of platinum, palladium, rhodium and gold electrodes in 1 M sulphuric acid by cyclic voltammetry'' Journal of Electroanalytical Chemistry and Interfacial Electrochemistry 1972, 35, 209-218.
[40] R. Gómez and J. M. Feliu, ''Rhodium adlayers on Pt(111) monocrystalline surfaces. Electrochemical behavior and electrocatalysis'' Electrochimica Acta 1998, 44, 1191-1205.
[41] R. Gómez, F. J. Gutiérrez de Dios and J. M. Feliu, ''Carbon monoxide oxidation and nitrous oxide reduction on Rh/Pt(111) electrodes'' Electrochimica Acta 2004, 49, 1195-1208.
[42] F. Maillard, G. Q. Lu, A. Wieckowski and U. Stimming, ''Ru-decorated Pt surfaces as model fuel cell electrocatalysts for CO electrooxidation'' Journal of Physical Chemistry B 2005, 109, 16230-16243.
[43] Z. D. Wei, L. L. Li, Y. H. Luo, C. Yan, C. X. Sun, G. Z. Yin and P. K. Shen, ''Electrooxidation of methanol on UPD-Ru and UPD-Sn modified Pt electrodes'' Journal of Physical Chemistry B 2006, 110, 26055-26061.
[44] J. Clavilier, J. M. Orts, J. M. Feliu and A. Aldaz, ''Study of the conditions for irreversible adsorption of lead at Pt(h,k,l) electrodes'' Journal of Electroanalytical Chemistry 1990, 293, 197-208.
[45] S. Chumillas, C. Busó-Rogero, J. Solla-Gullón, F. J. Vidal-Iglesias, E. Herrero and J. M. Feliu, ''Size and diffusion effects on the oxidation of formic acid and ethanol on platinum nanoparticles'' Electrochemistry Communications 2011, 13, 1194-1197.
[46] N. R. de Tacconi, R. O. Lezna, B. Beden, F. Hahn and C. Lamy, ''In-situ FTIR study of the electrocatalytic oxidation of ethanol at iridium and rhodium electrodes'' Journal of Electroanalytical Chemistry 1994, 379, 329-337.
[47] J. Souza-Garcia, E. Herrero and J. M. Feliu, ''Breaking the C-C Bond in the Ethanol Oxidation Reaction on Platinum Electrodes: Effect of Steps and Ruthenium Adatoms'' ChemPhysChem 2010, 11, 1391-1394.
[48] E. Herrero, K. Franaszczuk and A. Wieckowski, ''A voltammetric identification of the surface redox couple effective in methanol oxidation on a ruthenium-covered platinum (110) electrode'' Journal of Electroanalytical Chemistry 1993, 361, 269-273.
[49] M. Bełtowska-Brzezinska, T. Łuczak, J. Stelmach and R. Holze, ''The electrooxidation mechanism of formic acid on platinum and on lead ad-atoms modified platinum studied with the kinetic isotope effect'' Journal of Power Sources 2014, 251, 30-37.
[50] S. Uhm, S. T. Chung and J. Lee, ''Activity of Pt anode catalyst modified by underpotential deposited Pb in a direct formic acid fuel cell'' Electrochemistry Communications 2007, 9, 2027-2031.
[51] M. Watanabe and S. Motoo, ''Electrocatalysis by ad-atoms: Part II. Enhancement of oxidation of methanol on platinum by ruthenium ad-atoms'' Journal of Electroanalytical Chemistry 1975, 60, 267-273.
Chapter 7: Adatom modified shape-controlled platinum nanoparticles towards ethanol oxidation
250
[52] P. A. Christensen, S. W. M. Jones and A. Hamnett, ''In Situ FTIR Studies of Ethanol Oxidation at Polycrystalline Pt in Alkaline Solution'' Journal of Physical Chemistry C 2012, 116, 24681-24689.
[53] S. C. S. Lai, S. E. F. Kleijn, F. T. Z. Öztürk, V. C. van Rees Vellinga, J. Koning, P. Rodriguez and M. T. M. Koper, ''Effects of electrolyte pH and composition on the ethanol electro-oxidation reaction'' Catalysis Today 2010, 154, 92-104.
Capítulo 8: Conclusiones
253
Capítulo 8: Conclusiones
La presente tesis abarca estudios fundamentales para la oxidación de etanol y ácido
fórmico en nanopartículas de platino orientadas preferencialmente y poliorientadas
soportadas en carbón. El objetivo principal en estas investigaciones es el de completar la
oxidación hasta dióxido de carbono evitando la formación de veneno durante el transcurso
de la reacción. Partiendo del etanol, la molécula principalmente estudiada en la tesis, se
han realizado multitud de trabajos investigando diferentes parámetros que pueden afectar a
su reactividad, como es el caso de la estructura superficial del catalizador de platino, el
efecto de cambiar el pH de trabajo hasta llegar a disoluciones alcalinas, la importancia de
dispersar correctamente el depósito de nanopartículas en los soportes de carbón vítreo y,
por último, el cambio en la electrocatálisis al modificar la superficie de las nanopartículas
de platino con un átomo diferente. De acuerdo con estos estudios realizados con adátomos,
también se probó la efectividad de un electrodo modificado parecido para la oxidación de
ácido fórmico. Para el estudio de los mecanismos de oxidación implicados, se recurrieron a
técnicas electroquímicas (voltametría cíclica y cronoamperometría), espectro-
electroquímicas (FTIR de reflexión externa y ATR) y de espectrometría de masas (DEMS).
El primer trabajo presentado en la tesis (capítulo 2) corrobora, en nanopartículas de
platino con diferentes formas (indicativo de diferentes orientaciones cristalográficas), la
dependencia en la reactividad para la oxidación de etanol con la estructura superficial
observada en superficies monocristalinas, mostrándose los dominios 100 como más
apropiados para la rotura del enlace C-C del etanol (y también de CO formado) y los sitios
111 más adecuados para la formación de acetaldehído/ácido acético. Además, se estudia
el efecto de la adsorción competitiva del anión sulfato sobre la oxidación de etanol,
empleando para ello H2SO4 y HClO4. En ambos electrolitos soportes, dicha adsorción no
tiene efecto debido a la formación de ácido acético, cuyos aniones acetato formados
pueden competir con el etanol por los sitios activos del platino.
Para una aproximación al estudio del efecto del pH, el capítulo 3 indaga sobre la
reacción de oxidación de etanol en nanopartículas de platino con forma controlada,
Capítulo 8: Conclusiones
254
siempre sin superar valores de pH=4 en la disolución de trabajo. Con ayuda de
experimentos DEMS, se estudian las diferencias en cuanto al uso de las muestras con
orientación preferencial 100 y 111. La muestra con mayor presencia de dominios
100 se confirma como la mejor para la rotura del enlace C-C en la oxidación de etanol,
ratificándose la mayor eficiencia para la formación de CO2 en las nanopartículas (100)Pt
respecto a las (111)Pt. Al incrementar ligeramente el pH de la disolución de trabajo, la
formación de fragmentos CHx,ads a bajos potenciales aumenta respecto al veneno presente
en forma de COads. En la muestra de nanopartículas (111)Pt, al aumentar el pH la
formación de CO es impedida y, por tanto, se favorece cada vez más la formación de
acetaldehído/ácido acético.
El capítulo 4 se introduce de lleno en el estudio de la oxidación de etanol en medio
alcalino. Como no se dispone de resultados previos en superficies con estructura
superficial totalmente conocida, se realiza previamente el estudio con superficies
monocristalinas de platino, concretamente planos base y superficies escalonadas en largas
terrazas 111. La actividad es mucho mayor en medio alcalino que en medio ácido,
mostrándose el electrodo de Pt(111) como el que mayor corriente de oxidación presenta
seguido del electrodo de Pt(110) y del Pt(100), orden inverso al observado en medio ácido.
Sin embargo, la selectividad hasta la producción de CO2 es mucho menor, casi
despreciable en comparación con la cantidad de acetaldehído/acetato producida
independientemente de la orientación cristalográfica del electrodo de trabajo. Asimismo, la
desactivación de las superficies de platino es mucho mayor a causa de la polimerización
del acetaldehído formado en el catalizador que inhibe sucesivamente la oxidación de
etanol, principalmente en las superficies con mayor presencia de terrazas 111.
A continuación, de manera análoga al capítulo 4, el capítulo 5 experimenta la
oxidación de etanol en medio alcalino pero empleando las nanopartículas de platino con
forma controlada, concretamente las mismas muestras del capítulo 2. Los resultados del
capítulo 4 se corroboran con estas muestras de nanopartículas en cuanto al efecto de la
estructura superficial, relacionando los diferentes potenciales de adsorción de los OH con
el potencial observado para comenzar la oxidación de etanol en medio alcalino. Además,
los experimentos FTIR revelan que el acetato se forma casi con total exclusividad
independientemente de la muestra de nanopartículas de platino estudiada. Por otra parte, el
Capítulo 8: Conclusiones
255
uso de nanopartículas de platino poliorientadas con cantidad de metal variable soportadas
en carbón demuestra la importancia de la correcta dispersión del catalizador a lo largo del
soporte para impedir la aglomeración. Para solucionar este problema, se realiza el depósito
de las nanopartículas a la vez que se rota el soporte de carbón vítreo, lo cual favorece una
mayor dispersión de catalizador y un mejor comportamiento de éste, como se confirma con
la mayor actividad observada siguiendo un nuevo procedimiento de preparación que
promueve un depósito con las partículas más dispersas.
Las investigaciones con electrodos modificados de nanopartículas de platino con
átomos de un metal diferente se inician en el capítulo 6, empleando para ello las mismas
muestras (100)Pt y (111)Pt de los capítulos anteriores. El primer estudio se refiere a la
oxidación de ácido fórmico en las nanopartículas de platino con Tl adsorbido, el cual
favorece la oxidación de CO hasta CO2 a bajos potenciales, especialmente en la muestra
(100)Pt como se ratifica en experimentos FTIR. Se estudia el efecto de la diferente
concentración de ácido fórmico para los mismos electrodos modificados, mostrando como
aumenta la actividad para la oxidación de ácido fórmico a pesar de que se demuestra que el
mecanismo de oxidación no es tan sencillo como aparenta. A la vista de los resultados, se
acepta que el Tl ejerce un efecto de tercer cuerpo sobre la superficie de platino, impidiendo
la ruta indirecta de oxidación del ácido fórmico (por medio de la formación de CO) y
favoreciendo la ruta directa de oxidación de ácido fórmico, sin descartar los efectos
electrónicos.
Por último, el capítulo 7 trata de encontrar la combinación óptima entre las muestras
(100)Pt y (111)Pt y diferentes metales con el objetivo de completar la oxidación de etanol.
Se prueban todas las combinaciones posibles entre los adátomos Sn, Rh, Ru y Pb con las
dos muestras de nanopartículas de platino tanto en medio ácido como en medio alcalino.
Para las disoluciones 0.5 M H2SO4, los nanopartículas de platino modificadas con Sn son
las que muestran mejor comportamiento, principalmente con la mejora del potencial de
inicio de la oxidación de etanol en las dos muestras de nanopartículas estudiadas, e incluso,
para el caso de la (111)Pt, un incremento de la actividad. La explicación de este
comportamiento se asigna a la catálisis en la oxidación del CO hasta CO2 a bajos
recubrimientos, mientras que con grandes cantidades de estaño en la superficie de platino
se favorece la formación de ácido acético. Para el resto de superficies, el Ru únicamente
Capítulo 8: Conclusiones
256
mejora levemente las corrientes a bajos potenciales, indicando una catálisis en la
formación del CO2, mientras que el Pb también mejora ligeramente la actividad, aunque
sin llegar a alterar la distribución de productos. El Rh adsorbido sobre la superficie de
platino no ejerce ningún efecto positivo para la oxidación de etanol. En medio 0.1 M
NaOH, el mecanismo de reacción se modifica totalmente como se prueba en el capítulo 4,
así que las superficies combinadas más efectivas no son las mismas que en medio ácido.
Así, las superficies combinadas Pt-Ru no muestran ningún efecto catalítico en medio
alcalino, mientras que las superficies Pt-Sn, Pt-Rh y Pt-Pb enseñan pequeñas mejoras en el
potencial de inicio de oxidación del etanol, sin exponer cambios significativos en las
corrientes medidas, sobre todo en el caso de las muestras de nanopartículas (100)Pt.
Como conclusión general de toda la tesis, hay que resaltar que se han aportado
estudios fundamentales que confirman la tendencia en cuanto al efecto de la estructura
superficial en los mecanismos de la oxidación de etanol y ácido fórmico para las
nanopartículas de platino, tanto en medio ácido como en medio alcalino, prestando especial
atención a parámetros que pueden afectar la reactividad como la aglomeración de
partículas. Además, se ensayaron electrodos útiles desde el punto de vista electrocatalítico
para la oxidación de etanol en medio ácido, como es el caso de la combinación Pt-Sn para
la oxidación de etanol y la combinación de Pt-Tl para la oxidación de ácido fórmico,
aportando información valiosa para la posible elaboración de nuevos catalizadores a partir
de aleaciones bimetálicas válidas para estas dos reacciones.
257
Chapter 8: Conclusions
The present thesis includes fundamental studies for ethanol and formic acid oxidation
on shape-controlled and carbon supported platinum nanoparticles. The final aim of these
studies is to understand the oxidation process to achieve the complete oxidation to CO2,
avoiding the formation of undesired species during the reaction. Starting with ethanol, the
main molecule studied in this thesis, several investigations have been carried out on the
effect of different parameters on the reactivity. These parameters include the surface
structure of the platinum catalyst, the pH effect (containing alkaline solutions), the
importance of the correct nanoparticle dispersion on the carbon support and, finally, the
changes in the electrocatalysis after modifying the platinum nanoparticles surfaces with a
different adatoms. Modified platinum nanoparticles have been also used in the study of the
formic acid oxidation reaction. Electrochemical (cyclic voltammetry and
chronoamperometry), spectro-electrochemical (FTIR with external reflection and ATR)
and mass spectrometry techniques (DEMS) have been employed in the examination of the
oxidation mechanisms.
The first work presented in the thesis (chapter 2) demonstrates that the surface
structure trends observed with single crystal electrodes for the reactivity of ethanol
oxidation are also valid for the reactivity of shape-controlled platinum nanoparticles.
100 domains are effective for promoting the C-C bond scission, whereas 111 sites
favor acetaldehyde/acetic acid formation. On the other hand, the effect of the competitive
adsorption of sulfate is also investigated, employing H2SO4 and HClO4 solutions. In both
supporting electrolytes, this adsorption has no effect on the currents due to the presence of
acetate anions coming from the acetic acid production after ethanol oxidation, which can
compete with ethanol for the platinum active sites.
As an approach for the pH effect studies, chapter 3 deals on the ethanol oxidation
reaction in the same shape-controlled platinum nanoparticles, working always at pH values
lower than 4. Employing DEMS, the differences in reactivity between nanoparticles with
100 and 111 preferential domains are investigated. (100)Pt is confirmed as the best
Chapter 8: Conclusions
258
sample for the cleavage of the C-C bond, ratifying the higher efficiency compared with the
(111)Pt nanoparticles. When the pH of the working solution is increased, CHx,ads formation
is augmented at low potentials respect to the poison present in the form of COads. For the
(111)Pt nanoparticles sample, the formation of one-carbon fragments is prevented as pH
increases, favoring the acetaldehyde/acetic acid formation.
Chapter 4 addresses the subject of ethanol oxidation in alkaline medium. Since there
are no previous studies on the surface structure effect, experiments were carried out first
with surfaces with a well-defined structure, i.e., platinum single crystal electrodes,
especially basal planes and stepped surfaces with 111 terraces. The activity is higher in
alkaline media than in acidic media and the Pt(111) surface exhibits the largest oxidation
currents followed by Pt(110) and Pt(100), which is the opposite order to that obtained in
acidic solutions. However, selectivity for CO2 production is very low, almost negligible
when compared with the amount of acetaldehyde/acetate produced, regardless the
crystallographic orientation of the working electrode. Also, the Pt surfaces show a large
deactivation because of the polymerization of acetaldehyde formed on the catalyst, which
inhibits ethanol oxidation, mainly in surfaces with large 111 terraces.
After the fundamental studies with single crystal electrodes, chapter 5 investigates
ethanol oxidation in alkaline medium employing the same shape-controlled platinum
nanoparticles of the previous chapters, using similar approach than that carried out in
chapter 4. The results obtained there for the preferential acetate formation are confirmed
with these Pt nanoparticles samples. Additionally the onset of ethanol oxidation in alkaline
medium is related to the different potentials for the OH adsorption depending on the
crystallographic orientation. Additionally, it is also corroborated using IR experiments that
the almost only product formed in the oxidation is acetate, regardless of the shape-
controlled platinum nanoparticle sample employed. On the other hand, the studies with
spherical platinum nanoparticles supported on carbon with different metal loadings
demonstrate the importance of the correct catalyst dispersion on the support for preventing
the particle agglomeration. To solve this problem, the deposit is performed under rotation
of the glassy carbon, which optimizes the catalyst dispersion and its behavior, as it is
corroborated with the higher activity observed in ethanol oxidation observed after this new
preparation procedure.
Chapter 8: Conclusions
259
The studies with platinum nanoparticle electrodes modified by a foreign metal atom
are conducted in chapter 6, using the previously used (100)Pt and (111)Pt samples. The
first work refers to formic acid oxidation in platinum nanoparticles with adsorbed Tl, that
promotes CO oxidation to CO2 at low potentials, especially in the (100)Pt sample as it was
verified with FTIR experiments. The observed effect of the formic acid concentration in
the currents demonstrates that the oxidation mechanism is not as simple as it appears. From
the obtained results, it is accepted that Tl exercises a three-body effect on the platinum
surface, avoiding the indirect route of formic acid oxidation (after the CO formation) and
favoring the direct route for formic acid oxidation, without discarding the presence of
electronic effects.
At last, chapter 7 tries to find the optimal combination between (100)Pt and (111)Pt
samples and the different adatoms, with the objective of achieving the complete oxidation
of ethanol. All the possible combinations using Sn, Rh, Ru and Pb adatoms and the two
platinum nanoparticle samples in both acidic and alkaline mediums were tested. For 0.5 M
H2SO4 solutions, platinum nanoparticles modified by Sn present the better electrocatalytic
behavior, mainly for the improvement of the onset potential for ethanol oxidation in both
platinum nanoparticles studied. The explanation for this behavior is assigned to the
catalysis of CO oxidation to CO2 at lower coverages by a bifunctional mechanism, whereas
with higher tin coverages on the platinum surface, acetic acid formation is favored. For the
other surfaces, only Ru shows small improvements in the currents at low potentials
(indicating the catalysis in the CO2 production), whereas Pb also slightly enhances the
activity, although without altering the products distribution. Rh adsorbed on platinum
surface does not have any positive effect for ethanol oxidation. In 0.1 M NaOH, the
oxidation mechanism is completely different as was proved in chapter 4, causing a change
in the effectiveness of the mixed surfaces from that observed in acidic solutions. Thus, Pt-
Ru surfaces do not show any catalytic effect in alkaline medium, whereas Pt-Sn, Pt-Rh and
Pt-Pb display small improvements in the onset potential for ethanol oxidation, especially
for the (100)Pt nanoparticles sample. However, the experimental results do not show
significant changes in the measured currents.
As a general conclusion, this doctoral thesis provides fundamental studies which
confirm the tendency in the surface structure effect for ethanol and formic acid oxidation
Chapter 8: Conclusions
260
on the platinum nanoparticles in both acidic and alkaline medium, paying special attention
to different parameters such as the particles agglomeration that can affect the reactivity. In
addition, practical electrodes from the electrocatalytic viewpoint for ethanol (Pt-Sn) and
formic acid oxidation (Pt-Tl) in acidic solutions have been tested, providing valuable
information for the preparation of new catalysts using bimetallic alloys.
Lista de publicaciones
263
Lista de publicaciones
Publicaciones relacionadas con los trabajos realizados en la tesis:
1. Carlos Busó-Rogero; Vitali Grozovski; Francisco J. Vidal-Iglesias; José Solla-
Gullón; Enrique Herrero; Juan M. Feliu; Surface structure and anion effects in the
oxidation of ethanol on platinum nanoparticles, Journal of Materials Chemistry A,
Volume 1, Issue 24, Pages 7068-7076 (2013).
2. Carlos Busó-Rogero; Enrique Herrero; Juan M. Feliu, Ethanol Oxidation on Pt
Single-Crystal Electrodes: Surface-Structure Effects in Alkaline Medium,
ChemPhysChem, Volume 15, Issue 10, Pages 2019-2028 (2014).
3. Carlos Busó-Rogero, Juan V. Perales-Rondón; Manuel J. S. Farias; Francisco J.
Vidal-Iglesias; José Solla-Gullón; Enrique Herrero; Juan M. Feliu; Formic acid
electrooxidation on thallium-decorated shape-controlled platinum
nanoparticles: an improvement in electrocatalytic activity, Physical Chemistry
Chemical Physics, Volume 16, Issue 27, Pages 13616-13624 (2014).
4. Carlos Busó-Rogero; José Solla-Gullón; Francisco J. Vidal-Iglesias; E. Herrero; Juan
M. Feliu; Oxidation of ethanol on platinum nanoparticles: surface structure and
aggregation effects in alkaline medium, Journal of Solid State Electrochemistry,
Volume 20, Issue 4, Pages 1095-1106 (2016).
5. Carlos Busó-Rogero; Sylvain Brimaud; José Solla-Gullón; Francisco J. Vidal-
Iglesias; Enrique Herrero; R. Jürgen Behm; Juan M. Feliu; Ethanol oxidation on
shape-controlled platinum nanoparticles at different pHs: A combined in situ
IR spectroscopy and online mass spectrometry study, Journal of
Electroanalytical Chemistry, Volume 763, Pages 116-124 (2016).
6. Carlos Busó-Rogero; José Solla-Gullón; Francisco J. Vidal-Iglesias; Enrique
Herrero; Juan M. Feliu; Adatom modified shape-controlled platinum
Lista de publicaciones
264
nanoparticles towards ethanol oxidation, Electrochimica Acta, Volume 196, Pages
270-279 (2016).
Otras publicaciones:
7. Sara Chumillas; Carlos Busó-Rogero; José Solla-Gullón; Francisco J. Vidal-Iglesias;
Enrique Herrero; Juan M. Feliu; Size and diffusion effects on the oxidation of
formic acid and ethanol on platinum nanoparticles, Electrochemistry
Communications, Volume 13, Issue 11, Pages 1194-1197 (2011).
8. Carlos Busó-Rogero; Enrique Herrero; Jochen Bandlow; Aleix Comas-Vives; Timo
Jacob; CO oxidation on stepped-Pt(111) under electrochemical conditions:
insights from theory and experiment, Physical Chemistry Chemical Physics,
Volume 15, Issue 42, Pages 18671-18677 (2013).
9. Manuel J. S. Farias; Carlos Busó-Rogero, Rubén Gisbert, Enrique Herrero and Juan
M. Feliu, Influence of the CO Adsorption Environment on Its Reactivity with
(111) Terrace Sites in Stepped Pt Electrodes under Alkaline Media, Journal of
Physical Chemistry C, Volume 118, Issue 4, Pages 1925-1934 (2014).