7/25/2019 OPA2134 IC datasheet.
1/14
FEATURESSUPERIOR SOUND QUALITY
ULTRA LOW DISTORTION: 0.00008%
LOW NOISE: 8nV/Hz
TRUE FET-INPUT: IB= 5pAHIGH SPEED:
SLEW RATE: 20V/s
BANDWIDTH: 8MHz
HIGH OPEN-LOOP GAIN: 120dB (600)
WIDE SUPPLY RANGE: 2.5V to 18V
SINGLE, DUAL, AND QUAD VERSIONS
High PerformanceAUDIO OPERATIONAL AMPLIFIERS
TM
DESCRIPTIONThe OPA134 series are ultra-low distortion, low noiseoperational amplifiers fully specified for audio appli-cations. A true FET input stage was incorporated toprovide superior sound quality and speed for excep-tional audio performance. This in combination withhigh output drive capability and excellent dc perfor-mance allows use in a wide variety of demandingapplications. In addition, the OPA134s wide outputswing, to within 1V of the rails, allows increasedheadroom making it ideal for use in any audio circuit.
OPA134 op amps are easy to use and free from phaseinversion and overload problems often found in com-mon FET-input op amps. They can be operated from2.5V to 18V power supplies. Input cascode cir-cuitry provides excellent common-mode rejection andmaintains low input bias current over its wide inputvoltage range, minimizing distortion. OPA134 seriesop amps are unity-gain stable and provide excellentdynamic behavior over a wide range of load condi-tions, including high load capacitance. The dual and
quad versions feature completely independent cir-cuitry for lowest crosstalk and freedom from interac-tion, even when overdriven or overloaded.
Single and dual versions are available in 8-pin DIPand SO-8 surface-mount packages in standard con-figurations. The quad is available in 14-pin DIP andSO-14 surface mount packages. All are specified for40C to +85C operation. A SPICE macromodel isavailable for design analysis.
APPLICATIONSPROFESSIONAL AUDIO AND MUSIC
LINE DRIVERS
LINE RECEIVERS
MULTIMEDIA AUDIO
ACTIVE FILTERS
PREAMPLIFIERS
INTEGRATORS
CROSSOVER NETWORKS
1996 Burr-Brown Corporation PDS-1339C Printed in U.S.A. December, 1997
International Airport Industrial Park Mailing Address: PO Box 11400, Tucson, AZ 85734 Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 Tel: (520) 746-1111 Twx: 910-952-1111
Internet: http://www.burr-brown.com/ FAXLine: (800) 548-6133 (US/Canada Only) Cable: BBRCORP Telex: 066-6491 FAX: (520) 889-1510 Immediate Product Info: (800) 548-6132
1
2
3
4
8
7
6
5
V+
Out B
In B
+In B
Out A
In A
+In A
V
OPA2134
8-Pin DIP, SO-8
A
B
1
2
3
4
5
6
7
14
13
12
11
10
9
8
Out D
In D
+In D
V
+In C
In C
Out C
Out A
In A
+In A
V+
+In B
In B
Out B
OPA4134
14-Pin DIP
SO-14
A D
B C
1
2
3
4
8
7
6
5
Offset Trim
V+
Output
NC
Offset Trim
In
+In
V
OPA134
8-Pin DIP, SO-8
OPA134OPA2134OPA4134
OPA134OPA2134
OPA4134
OPA4134
OPA134 OPA2134
SBOS058
7/25/2019 OPA2134 IC datasheet.
2/14
2
OPA134/2134/4134
SPECIFICATIONSAt TA= +25C, VS= 15V, unless otherwise noted.
OPA134PA, UA
OPA2134PA, UA
OPA4134PA, UA
PARAMETER CONDITION MIN TYP MAX UNITS
AUDIO PERFORMANCETotal Harmonic Distortion + Noise G = 1, f = 1kHz, VO= 3Vrms
RL= 2k 0.00008 %RL= 600 0.00015 %
Intermodulation Distortion G = 1, f = 1kHz, VO= 1Vp-p 98 dB
Headroom(1) THD < 0.01%, RL= 2k, VS= 18V 23.6 dBu
FREQUENCY RESPONSE
Gain-Bandwidth Product 8 MHz
Slew Rate(2) 15 20 V/ sFull Power Bandwidth 1.3 MHz
Settling Time 0.1% G = 1, 10V Step, CL= 100pF 0.7 s0.01% G = 1, 10V Step, CL= 100pF 1 s
Overload Recovery Time (VIN) (Gain) = VS 0.5 s
NOISE
Input Voltage Noise
Noise Voltage, f = 20Hz to 20kHz 1.2 VrmsNoise Density, f = 1kHz 8 nV/ Hz
Current Noise Density, f = 1kHz 3 fA/ Hz
OFFSET VOLTAGEInput Offset Voltage 0.5 2 mV
TA= 40C to +85C 1 3(3) mVvs Temperature TA= 40C to +85C 2 V/Cvs Power Supply (PSRR) VS= 2.5V to 18V 90 106 dB
Channel Separation (Dual, Quad) dc, RL= 2k 135 dBf = 20kHz, RL= 2k 130 dB
INPUT BIAS CURRENT
Input Bias Current(4) VCM=0V +5 100 pAvs Temperature(3) See Typical Curve 5 nA
Input Offset Current(4) VCM=0V 2 50 pA
INPUT VOLTAGE RANGE
Common-Mode Voltage Range (V)+2.5 13 (V+)2.5 VCommon-Mode Rejection VCM= 12.5V to +12.5V 86 100 dB
TA= 40C to +85C 90 dB
INPUT IMPEDANCE
Differential 1013|| 2 || pF
Common-Mode VCM= 12.5V to +12.5V 1013
|| 5 || pFOPEN-LOOP GAIN
Open-Loop Voltage Gain RL= 10k, VO= 14.5V to +13.8V 104 120 dBRL= 2k, VO= 13.8V to +13.5V 104 120 dB
RL= 600, VO= 12.8V to +12.5V 104 120 dB
OUTPUT
Voltage Output RL= 10k (V)+0.5 (V+)1.2 VRL= 2k (V)+1.2 (V+)1.5 V
RL= 600 (V)+2.2 (V+)2.5 VOutput Current 35 mAOutput Impedance, Closed-Loop(5) f = 10kHz 0.01
Open-Loop f = 10kHz 10 Short-Circuit Current 40 mACapacitive Load Drive (Stable Operation) See Typical Curve
POWER SUPPLY
Specified Operating Voltage 15 VOperating Voltage Range 2.5 18 VQuiescent Current (per amplifier) IO= 0 4 5 mA
TEMPERATURE RANGE
Specified Range 40 +85 COperating Range 55 +125 CStorage 55 +125 CThermal Resistance, JA
8-Pin DIP 100 C/WSO-8 Surface-Mount 150 C/W14-Pin DIP 80 C/WSO-14 Surface-Mount 110 C/W
NOTES: (1) dBu = 20*log (Vrms/0.7746) where Vrms is the maximum output voltage for which THD+Noise is less than 0.01%. See THD+Noise text. (2) Guaranteed
by design. (3) Guaranteed by wafer-level test to 95% confidence level. (4) High-speed test at T J= 25C. (5) See Closed-Loop Output Impedance vs Frequencytypical curve.
7/25/2019 OPA2134 IC datasheet.
3/14
3 OPA134/2134/4134
PACKAGE
DRAWING TEMPERATURE
PRODUCT PACKAGE NUMBER(1) RANGE
Single
OPA134PA 8-Pin Plastic DIP 006 40C to +85COPA134UA SO-8 Surface-Mount 182 40C to +85C
Dual
OPA2134PA 8-Pin Plastic DIP 006 40C to +85COPA2134UA SO-8 Surface-Mount 182 40C to +85C
Quad
OPA4134PA 14-Pin Plastic DIP 010 40C to +85COPA4134UA SO-14 Surface-Mount 235 40C to +85C
NOTE: (1) For detailed drawing and dimension table, please see end of data
sheet, or Appendix C of Burr-Brown IC Data Book.
ELECTROSTATICDISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degrada-
tion to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
ABSOLUTE MAXIMUM RATINGS(1)
Supply Voltage, V+ to V.................................................................... 36V
Input Voltage .................................................... (V) 0.7V to (V+) +0.7V
Output Short-Circuit(2) .............................................................. Continuous
Operating Temperature ................................................. 40C to +125CStorage Temperature..................................................... 55C to +125CJunction Temperature...................................................................... 150CLead Temperature (soldering, 10s) ................................................. 300C
NOTES: (1) Stresses above these ratings may cause permanent damage.(2) Short-circuit to ground, one amplifier per package.
TYPICAL PERFORMANCE CURVESAt TA= +25C, VS= 15V, RL= 2k, unless otherwise noted.
TOTAL HARMONIC DISTORTION + NOISE
vs FREQUENCY
Frequency (Hz)
THD+Noise(%)
0.1
0.01
0.001
0.0001
0.00001
10 100 1k 10k 100k
2k600
RL
VO= 3VrmsG = +1
G = +10
SMPTE INTERMODULATION DISTORTION
vs OUTPUT AMPLITUDE
Output Amplitude (Vpp)
IMD(%)
1
0.1
0.010
0.001
0.0005
5
30m 0.1 1 10 30
G = +1
f = 1kHz
RL= 2k
Baseline
OP176
OPA134
OPA134
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the users own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
PACKAGE/ORDERING INFORMATION
7/25/2019 OPA2134 IC datasheet.
4/14
4
OPA134/2134/4134
HEADROOM TOTAL HARMONIC DISTORTION
+ NOISE vs OUTPUT AMPLITUDE
Output Amplitude (Vrms)
THD+
No
ise
(%)
1
0.1
0.010
0.001
0.0005
0.1 1 10 20
VS= 18VRL= 2kf = 1kHz
THD < 0.01%OPA134 11.7Vrms
OP176 11.1Vrms
Baseline
OP176OPA134
OPA134
TYPICAL PERFORMANCE CURVES (CONT)At TA= +25C, VS= 15V, RL= 2k, unless otherwise noted.
TOTAL HARMONIC DISTORTION + NOISE
vs FREQUENCY
Frequency (Hz)
THD+
No
ise
(%)
0.01
0.001
0.0001
0.00001
20 100 1k 10k 20k
VO= 10VrmsRL= 2k
VS= 16
VS= 17 VS= 18
HARMONIC DISTORTION + NOISE vs FREQUENCY
Frequency (Hz)
Amplitude(%o
fFundamentals)
0.01
0.001
0.0001
0.00001
0.000001
20 100 1k 10k 20k
2nd Harmonic
3rd Harmonic
VO= 1Vrms
RL=600
RL=2
k
VOLTAGE NOISE vs SOURCE RESISTANCE
Source Resistance ()
Vo
ltage
No
ise
(nV/Hz
)
1k
100
10
1
0.110 100 1k 10k 100k 1M 10M
OP176+
Resistor
OPA134+
Resistor
Resistor Noise
Only Vn(total) = (inRS)2+ en
2+ 4kTRS
INPUT VOLTAGE AND CURRENT NOISE
SPECTRAL DENSITY vs FREQUENCY
1
1k
100
10
Volta
geNoise(nV/Hz)
Frequency (Hz)
10 100 1k 10k 100k 1M
1
CurrentNoise(fA/Hz)
Voltage Noise
Current Noise
INPUT-REFERRED NOISE VOLTAGE
vs NOISE BANDWIDTH
Noise Bandwidth (Hz)
No
ise
Vo
ltage
(V)
100
10
1
0.1
1 10 100 1k 10k 100k
RS= 20
Peak-to-Peak
RMS
7/25/2019 OPA2134 IC datasheet.
5/14
5 OPA134/2134/4134
TYPICAL PERFORMANCE CURVES (CONT)At TA= +25C, VS= 15V, RL= 2k, unless otherwise noted.
OPEN-LOOP GAIN/PHASE vs FREQUENCY
0.1 1 10 100 1k 10k 100k 1M 10M
160
140
120
100
80
60
40
20
0
20
0
45
90
135
180
Vo
ltage
Ga
in(dB)
Phase
Shift()
Frequency (Hz)
G
CLOSED-LOOP GAIN vs FREQUENCY
Frequency (Hz)
Close
d-Loop
Ga
in(dB)
50
40
30
20
10
0
10
20
1k 10k 100k 1M 10M
G = +10
G = +100
G = +1
POWER SUPPLY AND COMMON-MODE REJECTION
vs FREQUENCY
Frequency (Hz)
PSR
,CMR(dB)
120
100
80
60
40
20
0
10 100 1k 10k 100k 1M
CMR
PSR
+PSR
MAXIMUM OUTPUT VOLTAGE
vs FREQUENCY
Frequency (Hz)
10k 100k 1M 10M
30
20
10
0
Out
putVoltage(Vp-p)
VS= 15V
VS= 2.5V
VS= 5V
Maximum output voltage
without slew-rate
induced distortion
CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY
Frequency (Hz)
Close
d-Loop
Ou
tpu
tImpe
dance
()
10
1
0.1
0.01
0.001
0.0001
10 100 1k 10k 100k
G = +1
G = +2
G = +10
G = +100
Note: Open-Loop
Output Impedance
at f = 10kHz is 10
CHANNEL SEPARATION vs FREQUENCY
Frequency (Hz)
Channe
lSepara
tion
(dB)
160
140
120
100
80
100 1k 10k 100k
Dual and quad devices.
G = 1, all channels.
Quad measured channel
A to D or B to Cother
combinations yield improved
rejection.
RL=
RL= 2k
7/25/2019 OPA2134 IC datasheet.
6/14
6
OPA134/2134/4134
FPO
TYPICAL PERFORMANCE CURVES (CONT)At TA= +25C, VS= 15V, RL= 2k, unless otherwise noted.
INPUT BIAS CURRENT vs TEMPERATURE
Ambient Temperature (C)
InputBiasCurrent(pA)
100k
10k
1k
100
10
1
0.1
75 50 25 0 25 50 75 100 125
Dual
Single
High Speed TestWarmed Up
INPUT BIAS CURRENT
vs INPUT COMMON-MODE VOLTAGE
Common-Mode Voltage (V)
InputBiasCurrent(pA)
10
9
8
7
6
5
4
3
2
1
0
15 10 5 0 5 10 15
High Speed Test
OPEN-LOOP GAIN vs TEMPERATURE
150
140
130
120
110
100
Open-Loop
Ga
in(dB)
Temperature (C)
75 50 25 0 25 50 75 100 125
RL= 600
RL= 2k
RL= 10k
CMR, PSR vs TEMPERATURE
Ambient Temperature (C)
CMR
,PSR(dB)
120
110
100
90
75 50 25 0 25 50 75 100 125
PSR
CMR
QUIESCENT CURRENT AND SHORT-CIRCUIT CURRENT
vs TEMPERATURE
Ambient Temperature (C)
QuiescentCurrentPerAmp(mA)
4.3
4.2
4.1
4.0
3.9
3.8
60
50
40
30
20
10
Short-CircuitCurrent(mA)
75 50 25 0 25 50 75 100 125
ISC
IQ
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT15
14
13
12
11
10
10
11
12
13
14
15
0 10 20 30 40 50 60
Output Current (mA)
Outpu
tVoltageSwing(V)
55C
55C
25C25C
85C
85C
125C
125C
25C
VIN= 15V
VIN= 15V
7/25/2019 OPA2134 IC datasheet.
7/14
7 OPA134/2134/4134
TYPICAL PERFORMANCE CURVES (CONT)At TA= +25C, VS= 15V, RL= 2k, unless otherwise noted.
SMALL-SIGNAL STEP RESPONSE
G =1, CL= 100pF
200ns/div
50mV/div
LARGE-SIGNAL STEP RESPONSE
G = 1, CL= 100pF
5V/div
1s/div
SETTLING TIME vs CLOSED-LOOP GAIN
Closed-Loop Gain (V/V)
SettlingTime(s)
100
10
1
0.11 10 100 1000
0.01%
0.1%
SMALL-SIGNAL OVERSHOOT
vs LOAD CAPACITANCE
60
50
40
30
20
10
0
100pF 1nF 10nF
Load Capacitance
Overs
hoo
t(%)
G = +1
G = 10
G = 1
OFFSET VOLTAGE PRODUCTION DISTRIBUTION
PercentofAmplifiers(%)
Offset Voltage (V)2000
1800
1600
1400
1200
1000
800
600
400
200 0
200
400
600
800
1000
1200
1400
1600
1800
2000
18
16
14
12
10
8
6
4
2
0
Typical production
distribution of packaged
units.
OFFSET VOLTAGE DRIFT
PRODUCTION DISTRIBUTION
PercentofAmplifiers(%)
Offset Voltage Drift (V/C)
0.5
1.5
2.5
3.5
4.5
5.5
6.5
7.5
8.5
9.5
10.5
11.5
12.5
12
10
8
6
4
2
0
Typical production
distribution of packaged
units.
7/25/2019 OPA2134 IC datasheet.
8/14
8
OPA134/2134/4134
APPLICATIONS INFORMATIONOPA134 series op amps are unity-gain stable and suitable
for a wide range of audio and general-purpose applications.
All circuitry is completely independent in the dual version,
assuring normal behavior when one amplifier in a package
is overdriven or short-circuited. Power supply pins should
be bypassed with 10nF ceramic capacitors or larger tominimize power supply noise.
OPERATING VOLTAGE
OPA134 series op amps operate with power supplies from
2.5V to 18V with excellent performance. Althoughspecifications are production tested with 15V supplies,most behavior remains unchanged throughout the full
operating voltage range. Parameters which vary signifi-
cantly with operating voltage are shown in the typical
performance curves.
OFFSET VOLTAGE TRIM
Offset voltage of OPA134 series amplifiers is laser trimmed
and usually requires no user adjustment. The OPA134(single op amp version) provides offset trim connections
on pins 1 and 8, identical to 5534 amplifiers. Offset
voltage can be adjusted by connecting a potentiometer as
shown in Figure 1. This adjustment should be used only to
null the offset of the op amp, not to adjust system offset or
offset produced by the signal source. Nulling offset could
change the offset voltage drift behavior of the op amp.
While it is not possible to predict the exact change in drift,
the effect is usually small.
TOTAL HARMONIC DISTORTION
OPA134 series op amps have excellent distortion character-
istics. THD+Noise is below 0.0004% throughout the audio
frequency range, 20Hz to 20kHz, with a 2k load. Inaddition, distortion remains relatively flat through its
wide output voltage swing range, providing increased head-
room compared to other audio amplifiers, including the
OP176/275.
FIGURE 1. OPA134 Offset Voltage Trim Circuit.
V+
V
100k
OPA134 single op amp only.
Use offset adjust pins only to null
offset voltage of op ampsee text.
Trim Range: 4mV typ
OPA134 6
7
8
4
3
2 1
10nF
10nF
In many ways headroom is a subjective measurement. It can
be thought of as the maximum output amplitude allowed
while still maintaining a very low level of distortion. In an
attempt to quantify headroom, we have defined very low
distortion as 0.01%. Headroom is expressed as a ratio
which compares the maximum allowable output voltagelevel to a standard output level (1mW into 600, or0.7746Vrms). Therefore, OPA134 series op amps, which
have a maximum allowable output voltage level of 11.7Vrms
(THD+Noise < 0.01%), have a headroom specification of
23.6dBu. See the typical curve Headroom - Total Harmonic
Distortion + Noise vs Output Amplitude.
DISTORTION MEASUREMENTS
The distortion produced by OPA134 series op amps is below
the measurement limit of all known commercially available
equipment. However, a special test circuit can be used to
extend the measurement capabilities.
Op amp distortion can be considered an internal error source
which can be referred to the input. Figure 2 shows a
circuit which causes the op amp distortion to be 101 times
greater than normally produced by the op amp. The addition
of R3 to the otherwise standard non-inverting amplifier
FIGURE 2. Distortion Test Circuit.
R2
OPA134
R1
Signal Gain = 1+
Distortion Gain = 1+
R3 VO= 3Vrms
Generator
Output
Analyzer
Input
Audio Precision
System One
Analyzer(1)
RL
1k
IBM PC
or
Compatible
SIG.
GAIN
DIST.
GAIN R1 R2 R3
100
10
1k
1k
1k
10
11
1
11
101
101
101
101
NOTE: (1) Measurement BW = 80kHz
R2R1
R2R1 II R3
7/25/2019 OPA2134 IC datasheet.
9/14
9 OPA134/2134/4134
VOUTVIN
R1
If RS> 2kor R1II R2> 2k
RS= R1II R2
R2
OPA134
configuration alters the feedback factor or noise gain of the
circuit. The closed-loop gain is unchanged, but the feedback
available for error correction is reduced by a factor of 101,
thus extending the resolution by 101. Note that the input
signal and load applied to the op amp are the same as with
conventional feedback without R3. The value of R3 should
be kept small to minimize its effect on the distortion mea-
surements.Validity of this technique can be verified by duplicating
measurements at high gain and/or high frequency where the
distortion is within the measurement capability of the test
equipment. Measurements for this data sheet were made
with an Audio Precision distortion/noise analyzer which
greatly simplifies such repetitive measurements. The mea-
surement technique can, however, be performed with manual
distortion measurement instruments.
SOURCE IMPEDANCE AND DISTORTION
For lowest distortion with a source or feedback network
which has an impedance greater than 2k, the impedanceseen by the positive and negative inputs in noninverting
applications should be matched. The p-channel JFETs in theFET input stage exhibit a varying input capacitance with
applied common-mode input voltage. In inverting configu-
rations the input does not vary with input voltage since the
inverting input is held at virtual ground. However, in
noninverting applications the inputs do vary, and the gate-
to-source voltage is not constant. The effect is increased
distortion due to the varying capacitance for unmatched
source impedances greater than 2k.
To maintain low distortion, match unbalanced source im-
pedance with appropriate values in the feedback network as
shown in Figure 3. Of course, the unbalanced impedance
may be from gain-setting resistors in the feedback path. If
the parallel combination of R1and R2is greater than 2k, amatching impedance on the noninverting input should be
used. As always, resistor values should be minimized to
reduce the effects of thermal noise.
FIGURE 3. Impedance Matching for Maintaining Low
Distortion in Non-Inverting Circuits.
NOISE PERFORMANCE
Circuit noise is determined by the thermal noise of external
resistors and op amp noise. Op amp noise is described by
two parametersnoise voltage and noise current. The total
noise is quantified by the equation:
With low source impedance, the current noise term is
insignificant and voltage noise dominates the noise perfor-
mance. At high source impedance, the current noise term
becomes the dominant contributor.
Low noise bipolar op amps such as the OPA27 and OPA37
provide very low voltage noise at the expense of a higher
current noise. However, OPA134 series op amps are unique
in providing very low voltage noise and very low current
noise. This provides optimum noise performance over a
wide range of sources, including reactive source imped-
ances, refer to the typical curve, Voltage Noise vs Source
Resistance. Above 2k source resistance, the op ampcontributes little additional noisethe voltage and current
terms in the total noise equation become insignificant andthe source resistance term dominates. Below 2k, op ampvoltage noise dominates over the resistor noise, but com-
pares favorably with other audio op amps such as OP176.
PHASE REVERSAL PROTECTION
OPA134 series op amps are free from output phase-reversal
problems. Many audio op amps, such as OP176, exhibit
phase-reversal of the output when the input common-mode
voltage range is exceeded. This can occur in voltage-fol-
lower circuits, causing serious problems in control loop
applications. OPA134 series op amps are free from this
undesirable behavior even with inputs of 10V beyond the
input common-mode range.
POWER DISSIPATION
OPA134 series op amps are capable of driving 600loadswith power supply voltage up to 18V. Internal powerdissipation is increased when operating at high supply
voltages. Copper leadframe construction used in OPA134
series op amps improves heat dissipation compared to con-
ventional materials. Circuit board layout can also help
minimize junction temperature rise. Wide copper traces help
dissipate the heat by acting as an additional heat sink.
Temperature rise can be further minimized by soldering the
devices to the circuit board rather than using a socket.
OUTPUT CURRENT LIMIT
Output current is limited by internal circuitry to approxi-
mately 40mA at 25C. The limit current decreases withincreasing temperature as shown in the typical performance
curve Short-Circuit Current vs Temperature.
V total i R e kTRn n S n s( ) ( )= + +2 2 4
7/25/2019 OPA2134 IC datasheet.
10/14
PACKAGING INFORMATION
Orderable Device Status (1) PackageType
PackageDrawing
Pins PackageQty
Eco Plan (2) Lead/Ball Finish MSL Peak Temp(3)
OPA134PA ACTIVE PDIP P 8 50 Green (RoHS &
no Sb/Br)
CU NIPDAU N / A for Pkg Type
OPA134PA3 OBSOLETE PDIP P 8 TBD Call TI Call TI
OPA134PAG4 ACTIVE PDIP P 8 50 Green (RoHS &no Sb/Br)
CU NIPDAU N / A for Pkg Type
OPA134UA ACTIVE SOIC D 8 100 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA134UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA134UA/2K5E4 ACTIVE SOIC D 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA134UA3 OBSOLETE PDIP P 8 TBD Call TI Call TI
OPA134UAE4 ACTIVE SOIC D 8 100 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA134UAG4 ACTIVE SOIC D 8 100 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA2134PA ACTIVE PDIP P 8 50 Green (RoHS &no Sb/Br)
CU NIPDAU N / A for Pkg Type
OPA2134PAG4 ACTIVE PDIP P 8 50 Green (RoHS &no Sb/Br)
CU NIPDAU N / A for Pkg Type
OPA2134UA ACTIVE SOIC D 8 100 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA2134UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA2134UA/2K5E4 ACTIVE SOIC D 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA2134UAE4 ACTIVE SOIC D 8 100 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA2134UAG4 ACTIVE SOIC D 8 100 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA4134PA OBSOLETE PDIP N 14 TBD Call TI Call TI
OPA4134UA ACTIVE SOIC D 14 58 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA4134UA/2K5 ACTIVE SOIC D 14 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA4134UA/2K5E4 ACTIVE SOIC D 14 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
OPA4134UAE4 ACTIVE SOIC D 14 58 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
SN412008DRE4 ACTIVE SOIC D 8 2500 Green (RoHS &no Sb/Br)
CU NIPDAU Level-3-260C-168 HR
(1) The marketing status values are defined as follows:ACTIVE:Product device recommended for new designs.LIFEBUY:TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.NRND:Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part ina new design.PREVIEW:Device has been announced but is not in production. Samples may or may not be available.OBSOLETE:TI has discontinued the production of the device.
PACKAGE OPTION ADDENDUM
www.ti.com 22-Oct-2007
Addendum-Page 1
7/25/2019 OPA2134 IC datasheet.
11/14
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please checkhttp://www.ti.com/productcontentfor the latest availability information and additional product content details.TBD:The Pb-Free/Green conversion plan has not been defined.Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirementsfor all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be solderedat high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die andpackage, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHScompatible) as defined above.Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flameretardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak soldertemperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it isprovided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to theaccuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to takereasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis onincoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limitedinformation may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TIto Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com 22-Oct-2007
Addendum-Page 2
http://www.ti.com/productcontenthttp://www.ti.com/productcontent7/25/2019 OPA2134 IC datasheet.
12/14
TAPE AND REEL BOX INFORMATION
Device Package Pins Site ReelDiameter
(mm)
ReelWidth(mm)
A0 (mm) B0 (mm) K0 (mm) P1(mm)
W(mm)
Pin1Quadrant
OPA134UA/2K5 D 8 SITE 41 330 12 6.9 5.4 2.0 8 12 Q1
OPA2134UA/2K5 D 8 SITE 41 330 12 6.9 5.4 2.0 8 12 Q1
OPA4134UA/2K5 D 14 SITE 41 330 16 6.5 9.5 2.1 8 16 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 4-Oct-2007
Pack Materials-Page 1
7/25/2019 OPA2134 IC datasheet.
13/14
Device Package Pins Site Length (mm) Width (mm) Height (mm)
OPA134UA/2K5 D 8 SITE 41 346.0 346.0 29.0
OPA2134UA/2K5 D 8 SITE 41 346.0 346.0 29.0
OPA4134UA/2K5 D 14 SITE 41 346.0 346.0 33.0
PACKAGE MATERIALS INFORMATION
www.ti.com 4-Oct-2007
Pack Materials-Page 2
7/25/2019 OPA2134 IC datasheet.
14/14
I M P O R T A N T N O T I C E
T e x a s I n s t r u m e n t s I n c o r p o r a t e d a n d i t s s u b s i d i a r i e s ( T I ) r e s e r v e t h e r i g h t t o m a k e c o r r e c t i o n s , m o d i f i c a t i o n s , e n h a n c e m e n t s , i m p r o v e m e n t s , a n d o t h e r c h a n g e s t o i t s p r o d u c t s a n d s e r v i c e s a t a n y t i m e a n d t o d i s c o n t i n u e a n y p r o d u c t o r s e r v i c e w i t h o u t n o t i c e . C u s t o m e r s s h o u l d o b t a i n t h e l a t e s t r e l e v a n t i n f o r m a t i o n b e f o r e p l a c i n g o r d e r s a n d s h o u l d v e r i f y t h a t s u c h i n f o r m a t i o n i s c u r r e n t a n d c o m p l e t e . A l l p r o d u c t s a r e s o l d s u b j e c t t o T I s t e r m s a n d c o n d i t i o n s o f s a l e s u p p l i e d a t t h e t i m e o f o r d e r a c k n o w l e d g m e n t .
T I w a r r a n t s p e r f o r m a n c e o f i t s h a r d w a r e p r o d u c t s t o t h e s p e c i f i c a t i o n s a p p l i c a b l e a t t h e t i m e o f s a l e i n a c c o r d a n c e w i t h T I s
s t a n d a r d w a r r a n t y . T e s t i n g a n d o t h e r q u a l i t y c o n t r o l t e c h n i q u e s a r e u s e d t o t h e e x t e n t T I d e e m s n e c e s s a r y t o s u p p o r t t h i s w a r r a n t y . E x c e p t w h e r e m a n d a t e d b y g o v e r n m e n t r e q u i r e m e n t s , t e s t i n g o f a l l p a r a m e t e r s o f e a c h p r o d u c t i s n o t n e c e s s a r i l y p e r f o r m e d .
T I a s s u m e s n o l i a b i l i t y f o r a p p l i c a t i o n s a s s i s t a n c e o r c u s t o m e r p r o d u c t d e s i g n . C u s t o m e r s a r e r e s p o n s i b l e f o r t h e i r p r o d u c t s a n d a p p l i c a t i o n s u s i n g T I c o m p o n e n t s . T o m i n i m i z e t h e r i s k s a s s o c i a t e d w i t h c u s t o m e r p r o d u c t s a n d a p p l i c a t i o n s , c u s t o m e r s s h o u l d p r o v i d e a d e q u a t e d e s i g n a n d o p e r a t i n g s a f e g u a r d s .
T I d o e s n o t w a r r a n t o r r e p r e s e n t t h a t a n y l i c e n s e , e i t h e r e x p r e s s o r i m p l i e d , i s g r a n t e d u n d e r a n y T I p a t e n t r i g h t , c o p y r i g h t , m a s k w o r k r i g h t , o r o t h e r T I i n t e l l e c t u a l p r o p e r t y r i g h t r e l a t i n g t o a n y c o m b i n a t i o n , m a c h i n e , o r p r o c e s s i n w h i c h T I p r o d u c t s o r s e r v i c e s a r e u s e d . I n f o r m a t i o n p u b l i s h e d b y T I r e g a r d i n g t h i r d - p a r t y p r o d u c t s o r s e r v i c e s d o e s n o t c o n s t i t u t e a l i c e n s e f r o m T I t o u s e s u c h p r o d u c t s o r s e r v i c e s o r a w a r r a n t y o r e n d o r s e m e n t t h e r e o f . U s e o f s u c h i n f o r m a t i o n m a y r e q u i r e a l i c e n s e f r o m a t h i r d p a r t y u n d e r t h e p a t e n t s o r o t h e r i n t e l l e c t u a l p r o p e r t y o f t h e t h i r d p a r t y , o r a l i c e n s e f r o m T I u n d e r t h e p a t e n t s o r o t h e r i n t e l l e c t u a l p r o p e r t y o f T I .
R e p r o d u c t i o n o f T I i n f o r m a t i o n i n T I d a t a b o o k s o r d a t a s h e e t s i s p e r m i s s i b l e o n l y i f r e p r o d u c t i o n i s w i t h o u t a l t e r a t i o n a n d i s a c c o m p a n i e d b y a l l a s s o c i a t e d w a r r a n t i e s , c o n d i t i o n s , l i m i t a t i o n s , a n d n o t i c e s . R e p r o d u c t i o n o f t h i s i n f o r m a t i o n w i t h a l t e r a t i o n i s a n u n f a i r a n d d e c e p t i v e b u s i n e s s p r a c t i c e . T I i s n o t r e s p o n s i b l e o r l i a b l e f o r s u c h a l t e r e d d o c u m e n t a t i o n . I n f o r m a t i o n o f t h i r d p a r t i e s m a y b e s u b j e c t t o a d d i t i o n a l r e s t r i c t i o n s .
R e s a l e o f T I p r o d u c t s o r s e r v i c e s w i t h s t a t e m e n t s d i f f e r e n t f r o m o r b e y o n d t h e p a r a m e t e r s s t a t e d b y T I f o r t h a t p r o d u c t o r s e r v i c e v o i d s a l l e x p r e s s a n d a n y i m p l i e d w a r r a n t i e s f o r t h e a s s o c i a t e d T I p r o d u c t o r s e r v i c e a n d i s a n u n f a i r a n d d e c e p t i v e b u s i n e s s p r a c t i c e . T I i s n o t r e s p o n s i b l e o r l i a b l e f o r a n y s u c h s t a t e m e n t s .
T I p r o d u c t s a r e n o t a u t h o r i z e d f o r u s e i n s a f e t y - c r i t i c a l a p p l i c a t i o n s ( s u c h a s l i f e s u p p o r t ) w h e r e a f a i l u r e o f t h e T I p r o d u c t w o u l d r e a s o n a b l y b e e x p e c t e d t o c a u s e s e v e r e p e r s o n a l i n j u r y o r d e a t h , u n l e s s o f f i c e r s o f t h e p a r t i e s h a v e e x e c u t e d a n a g r e e m e n t s p e c i f i c a l l y g o v e r n i n g s u c h u s e . B u y e r s r e p r e s e n t t h a t t h e y h a v e a l l n e c e s s a r y e x p e r t i s e i n t h e s a f e t y a n d r e g u l a t o r y r a m i f i c a t i o n s o f t h e i r a p p l i c a t i o n s , a n d a c k n o w l e d g e a n d a g r e e t h a t t h e y a r e s o l e l y r e s p o n s i b l e f o r a l l l e g a l , r e g u l a t o r y a n d s a f e t y - r e l a t e d r e q u i r e m e n t s c o n c e r n i n g t h e i r p r o d u c t s a n d a n y u s e o f T I p r o d u c t s i n s u c h s a f e t y - c r i t i c a l a p p l i c a t i o n s , n o t w i t h s t a n d i n g a n y a p p l i c a t i o n s - r e l a t e d i n f o r m a t i o n o r s u p p o r t t h a t m a y b e p r o v i d e d b y T I . F u r t h e r , B u y e r s m u s t f u l l y i n d e m n i f y T I a n d i t s r e p r e s e n t a t i v e s a g a i n s t a n y d a m a g e s a r i s i n g o u t o f t h e u s e o f T I p r o d u c t s i n s u c h s a f e t y - c r i t i c a l a p p l i c a t i o n s .
T I p r o d u c t s a r e n e i t h e r d e s i g n e d n o r i n t e n d e d f o r u s e i n m i l i t a r y / a e r o s p a c e a p p l i c a t i o n s o r e n v i r o n m e n t s u n l e s s t h e T I p r o d u c t s a r e s p e c i f i c a l l y d e s i g n a t e d b y T I a s m i l i t a r y - g r a d e o r " e n h a n c e d p l a s t i c . " O n l y p r o d u c t s d e s i g n a t e d b y T I a s m i l i t a r y - g r a d e m e e t m i l i t a r y s p e c i f i c a t i o n s . B u y e r s a c k n o w l e d g e a n d a g r e e t h a t a n y s u c h u s e o f T I p r o d u c t s w h i c h T I h a s n o t d e s i g n a t e d a s m i l i t a r y - g r a d e i s s o l e l y a t t h e B u y e r ' s r i s k , a n d t h a t t h e y a r e s o l e l y r e s p o n s i b l e f o r c o m p l i a n c e w i t h a l l l e g a l a n d r e g u l a t o r y r e q u i r e m e n t s i n c o n n e c t i o n w i t h s u c h u s e .
T I p r o d u c t s a r e n e i t h e r d e s i g n e d n o r i n t e n d e d f o r u s e i n a u t o m o t i v e a p p l i c a t i o n s o r e n v i r o n m e n t s u n l e s s t h e s p e c i f i c T I p r o d u c t s a r e d e s i g n a t e d b y T I a s c o m p l i a n t w i t h I S O / T S 1 6 9 4 9 r e q u i r e m e n t s . B u y e r s a c k n o w l e d g e a n d a g r e e t h a t , i f t h e y u s e a n y n o n - d e s i g n a t e d p r o d u c t s i n a u t o m o t i v e a p p l i c a t i o n s , T I w i l l n o t b e r e s p o n s i b l e f o r a n y f a i l u r e t o m e e t s u c h r e q u i r e m e n t s .
F o l l o w i n g a r e U R L s w h e r e y o u c a n o b t a i n i n f o r m a t i o n o n o t h e r T e x a s I n s t r u m e n t s p r o d u c t s a n d a p p l i c a t i o n s o l u t i o n s :
P r o d u c t s A p p l i c a t i o n s
A m p l i f i e r s a m p l i f i e r . t i . c o m A u d i o w w w . t i . c o m / a u d i o
D a t a C o n v e r t e r s d a t a c o n v e r t e r . t i . c o m A u t o m o t i v e w w w . t i . c o m / a u t o m o t i v e
D S P d s p . t i . c o m B r o a d b a n d w w w . t i . c o m / b r o a d b a n d
I n t e r f a c e i n t e r f a c e . t i . c o m D i g i t a l C o n t r o l w w w . t i . c o m / d i g i t a l c o n t r o l
L o g i c l o g i c . t i . c o m M i l i t a r y w w w . t i . c o m / m i l i t a r y
P o w e r M g m t p o w e r . t i . c o m O p t i c a l N e t w o r k i n g w w w . t i . c o m / o p t i c a l n e t w o r k
M i c r o c o n t r o l l e r s m i c r o c o n t r o l l e r . t i . c o m S e c u r i t y w w w . t i . c o m / s e c u r i t y
R F I D w w w . t i - r f i d . c o m T e l e p h o n y w w w . t i . c o m / t e l e p h o n y L o w P o w e r w w w . t i . c o m / l p w V i d e o & I m a g i n g w w w . t i . c o m / v i d e o W i r e l e s s
W i r e l e s s w w w . t i . c o m / w i r e l e s s
M a i l i n g A d d r e s s : T e x a s I n s t r u m e n t s , P o s t O f f i c e B o x 6 5 5 3 0 3 , D a l l a s , T e x a s 7 5 2 6 5 C o p y r i g h t 2 0 0 7 , T e x a s I n s t r u m e n t s I n c o r p o r a t e d
http://www.ti.com/wirelesshttp://www.ti.com/lpwhttp://www.ti.com/videohttp://microcontroller.ti.com/http://www.ti.com/securityhttp://power.ti.com/http://logic.ti.com/http://www.ti.com/militaryhttp://interface.ti.com/http://www.ti.com/digitalcontrolhttp://dsp.ti.com/http://www.ti.com/broadbandhttp://amplifier.ti.com/http://www.ti.com/audiohttp://www.ti.com/wirelesshttp://www.ti.com/videohttp://www.ti.com/lpwhttp://www.ti.com/telephonyhttp://www.ti-rfid.com/http://www.ti.com/securityhttp://microcontroller.ti.com/http://www.ti.com/opticalnetworkhttp://power.ti.com/http://www.ti.com/militaryhttp://logic.ti.com/http://www.ti.com/digitalcontrolhttp://interface.ti.com/http://www.ti.com/broadbandhttp://dsp.ti.com/http://www.ti.com/automotivehttp://dataconverter.ti.com/http://www.ti.com/audiohttp://amplifier.ti.com/