presentation new
-
Upload
elizabeth-kharchenko -
Category
Documents
-
view
76 -
download
2
Transcript of presentation new
MODERN GREEN TECHNOLOGIES
FOR AFFORDABLE PRICES
AERATED CONCRETE
PRODUCTION LINES
Wide range of production lines fits
needs of each client
Inntech Start
Stationary production
lines with capacity up
from 10 to 49 m3 of
NAAC blocks per day.
Inntech Profi
Automated production
lines. Capacity is up
from 60 to 500 m3
NAAC blocks per day
Inntech Master
Semi-automatic
production lines. Capacity
is from 30 up to 49,6 m3
NAAC blocks per day
What is NAAC?
Aerated concrete is classified as cellular concrete. It isbuilding material which consists of air-bubble voids. Thatstructure makes aircrete one of the most efficient buildingmaterial because of its physicotechnical qualities
Aerated concrete can be classified by the way of hardening:
• autoclaved which harden under excessive pressure and higher-temperature in special furnace - autoclaves;
• non – autoclaved which harden naturally or under steam curing. Moreover non-autoclaved aerated concrete production requires hundreds times less investments than autoclaved production method.
FEATURES OF
NAACEco-friendly Air- and Water-Resistant High compressive
strength
Economical easy
to install
Earthquake-
resistant
Fire resistant Sound-proofing
Сomparative analysis of aerated concrete blocks produced by
INNTECHGROUP company and other wall materials
Characteristic Unit Red brick
Vibro-
compressed
concrete hollow
blocks
Foamed
concrete
Aerated
concrete
Density Kg/m3 1400-1700 1500-1800 800 600
Thermal
conductivity watt/m°K 0,45-0,7 0,4-0,56 0,25 0,14
Freeze resistance cycle F-32 F-25 F-35 F-50 F-35 F-50 F-25
Usage of masonry
mortar per 1m2 of
wall m3 0,24 0,18 0,11-0,15 0,11
Deviation of
geometrical
dimensions mm 5-10 1-5 1-3 1-3
Adhesion
(connection) of
finishing mortar - yes yes no yes
Load on foundation - high middle low low
Required wall
thickness with equal
thermal conductivity mm 250 200 120 75
How to produce NAAC Block?
The main components for the production of NAAC :
Cement SandAluminum powder
You can use
Fly Ash
instead of
sand
Chemical
additives
Where to use?For construction of 2-3 – storeyed houses
As a filler for non-load-bearing walls in construction of
monolithic wireframe House
Construction of partition walls
By using of the construction of aerated concrete, you ensure that your
home and other buildings have a number of significant advantages over
traditional building materials:
• Easy to install
• Dimensional accuracy + -1-2 mm
• Reduction of labor costs and material consumption
• Fire safety
• Savings of 20% -30% of your air conditioning
• Good sound insulation performance
• Excellent aseismicstrength.
Distinctive features of this line
• Mobile mould with bigger
sizes: 2400x600 600 mm
(0,86 m3)
• Moulds are moved by
hydraulic pusher
• Strain-gauge weighing
principle by pushing the
button
• Components
pneumatically unloaded
into the mixer
• High-performance cutting device allows to manufacture NAAC
blocks of almost any sizes
• Array is cut by vertical and horizontal cutting machines to
promote perfect geometry of block
• Frequency-regulated drive of cutting device enables to
produce blocks with perfectly smooth as well as with rough
surface
• Vibration technology for lifting of NAAC array
• Handles cutting machine for large-sized blocks
Requirements for working room
Placement of equipment (t>15C), sq.m From 400
Warm warehouse for products (t>0C), sq.m 100
Providing of water and electricity
•Compact design
• Highest possible output
from each square meter
• Maximum automatization of
the production
Advantages of Inntech Profi
Semi-automatic non-autoclaved aerated concrete
blocks production lines Inntech Master with capacity
from 30 up to 50 m3/day
Distinctive features of this line
Requirements for working room
Placement of equipment (t>15C), sq.m from 250
Warm warehouse for products (t>0C),
sq.m80
Providing of water and electricity
Mobile mould with sizes
2400х600х300 (0,42 m3 )
Components manually unloaded
into the mixer
Moulds are moved by mechanical
pusher
•Cutting of the array is
performed by vertical
cutting machine
•Frequency-regulated
drive of cutting device
enables to produce
blocks with perfectly
smooth as well as with
rough surface
•Strain-
gauge weighing
principle by pushing
the button
Medium
automatization of the
production
Stationary production lines Inntech Start with
capacity from 10 to 49 m3 of NAAC blocks per day
The set of equipment can be upgraded from low
automatization of the production process to
medium level
Distinctive features
Requirements for working room
Placement of
equipment (t>15C),
sq.m
from 160
Warm warehouse for
products (t>0C), sq.m50
Providing of water
and electricity
•Fixed moulds (2000х1200х300 mm (0,72 m3) )
•Mixer for aerated concrete moves from point of dosage to molds
•Dosing of the components is carried out by weight batches of sand and
cement hoppers or manually .
•Cutting of an array is performed manually by conductor with special saws.
About us
• We have been meeting our customers'
requirements and international quality
standards competitively thanks to our
highly qualified staff.
• Our customized approach results in
regular introduction of new technologies
and development of new product lines.
• Our production and warehousing
facilities enable to maintain production
schedules and the efficient delivery of
final product to end customer.
LLC TPC INNTECHGROUP is modern Russian company that designs and manufactures the equipment for non-autoclaved aerated concrete
LLC Inntechgroup is proud of our diverse worldwide
customer base which includes clients from numerous
countries such as CIS countries, South and Southeast Asia,
Middle East
•free individual layout solutions which will suit
your building
•development of individual NAAC mixture
composition basing on locally available raw
materials
• guarantee and post-guarantee maintenance
services,
•advisory services at each step,
•start up of production, teaching customer’s
staff
We provide partners and clients with extensive
technologic and engineering support:
We sincerely hope that the information will help you to make
an informed decision about our production lines!
Best regards,
Inntechgroup team
Tel.: +7(3852) 22 22 01, +7(3852) 53 35 25, +7 964 603 35 25
www.inntg.com [email protected]