Conector TGC Presentacion

8/12/2019 Conector TGC Presentacion

1/29

TGCTGC

Transversa lTransversa l Gr oun d in g Conn ect o rGr oun d in g Conn ect o r


2/29


3/29

Groun d in g Conn ect o rGr oun d in g Conn ect o rGener i c Requ i r em ent sGener i c Requ i r em ent s

n Temperature Cycling

4 Fault Current Draining.

n Tests/Standards depend on adopted standards

4 Grounding connectors should be made of alloys which are at least 80% copper

and/or stainless steel.


4/29

~~Transversal Grounding Connector~~

Transversal connector for groundingTransversal connector for grounding

power distribution, telecommunicationpower distribution, telecommunication

equipment, and residential, industrialequipment, and residential, industrial

applications.applications.


5/29

CHARACTERI STI CSCHARACTERI STI CS

nn It can be used in adverse temperature and humidityIt can be used in adverse temperature and humidityenvironments.environments.

nn Neither crimping tools nor special moulds areNeither crimping tools nor special moulds are

requiredrequired..

nn It is possible to rework the grounding circuitry asIt is possible to rework the grounding circuitry as

necessary, because the installation and removal arenecessary, because the installation and removal areboth very swiftboth very swiftand it is not necessary to cut theand it is not necessary to cut thewires.wires.


6/29


nn A safety lock allows the installer to check if theA safety lock allows the installer to check if theinstallation has been successfully completedinstallation has been successfully completed..

nn Complies with a wide wire range with a reducedComplies with a wide wire range with a reducedconnectors range.connectors range.

nn All materials have been carefully chosen andAll materials have been carefully chosen and

selected for high mechanical resistance, highselected for high mechanical resistance, highconductivity, resistance to corrosion and are notconductivity, resistance to corrosion and are notsubject to ssubject to stresstresscorrosioncorrosion..


7/29


nn The application is performed simply using aThe application is performed simply using a pairpair ofof

gas pliersgas pliers..

nn Bending the wire during the installation is notBending the wire during the installation is notnecessary.necessary.

nn The body provides a spring action, whichThe body provides a spring action, whichguarantees the connection.guarantees the connection.


8/29

Com ponen t s and Mat e r i al sCom ponen t s and Mat e r i al s

WING -WING -

Copper AlloyCopper Alloy

C -C -

Stainless SteelStainless Steel


9/29

App l i ca t i onApp l i ca t i on

nn Put the wire intoPut the wire intothetheCCmembermember,,

as shown in theas shown in the

figure.figure.


10/29


nn Insert theInsert the WINGWING

through the Cthrough the C

opening.opening.


11/29


nn Slide the connectorSlide the connector

down thedown the rodrod..


12/29


nn Tighten the WING using theTighten the WING using the gas pliersgas pliers..


13/29


14/29

App l i ca t i onApp l i ca t i on RangeRange

ROD-CABLE CONEXIONSROD-CABLE CONEXIONS

ROD:ROD: 1/21/2, 5/8, 5/8and 3/4and 3/4

CABLES:CABLES: 6 - 35 mm2 6 - 35 mm2

CABLE-CABLE CONEXIONSCABLE-CABLE CONEXIONS

CABLES: 35 mm2CABLES: 35 mm2


15/29

T G C -T G C - Spec i f i ca t ionsSpec i f i ca t ions

Product SpecificationProduct Specification108-37051108-37051

Instruction SheetInstruction Sheet411-37030411-37030

Test ReportTest Report0894/000894/00

44UL 486-AUL 486-A

44UL 467UL 467

44Bellcore TR-NWT-001075Bellcore TR-NWT-001075


16/29


17/29

T G C -T G C - Tes t ingTes t ing

UL 467:UL 467:

n Current Test

4Procedure:The samples must be submitted to a specified current for aThe samples must be submitted to a specified current for a

predefined period of time, which values vary in accordance with the conductorpredefined period of time, which values vary in accordance with the conductor

size.size. (Ex.: 35 mm(Ex.: 35 mm22

conductorconductor

I = 3 900 A for 6I = 3 900 A for 6 secondsseconds).).

n 4Requirement:After having been submitted to the above current level, theAfter having been submitted to the above current level, the

sample must present continuity and must not show signs of cracking, solder orsample must present continuity and must not show signs of cracking, solder or

separated parts.separated parts.

n Pullout Test

44Procedure:The same samples from the Current Test must be submittedThe same samples from the Current Test must be submitted to ato aloadload of 667 N for 5 minutes.of 667 N for 5 minutes.

44Requirement:It should withstand the above load withIt should withstand the above load with nonoevidence of slippageevidence of slippage..


18/29


Bellcore TR-NWT-001075Bellcore TR-NWT-001075::

TestsTests Sequence Sequence

Resistance TestResistance Test 1, 4, 6, 8, 10, 13, 151, 4, 6, 8, 10, 13, 15Vibration TestVibration Test 22

Tensile TestTensile Test 33

Temperature and Humidity Cycling TestTemperature and Humidity Cycling Test 55

H2S Exposure TestH2S Exposure Test 77

Salt Fog TestSalt Fog Test 99

AC Fault CurrentAC Fault Current 11 11Pullout TestPullout Test 12, 16 12, 16

Lightning Surge TestLightning Surge Test 14 14


19/29

T G C -T G C - Tr ia lsTr ia ls


1) Electrical Resistance - Initial

44Procedure:The resistance between the wires/rods must be measured.

44Requirement:This must not be greater than 10M.

2) Vibration Test

44Procedure:The samples must be placed in a vibration test machine for 2 hours ineach assembly shaft.

44Requirement:There must be no signs of cracking or loose connector parts.


20/29

T G C -T G C - Tes t ingTes t ing(V ib ra t ion Tes t -(V ib ra t ion Test - D i rec t ionDi rec t ion1 )1 )


21/29

T G C -T G C - Tes t ingTes t ing(V ib ra t ion Test -(V ib ra t ion Test - D i rec t i onD i rec t i on2 )2 )


22/29

T G C -T G C - Tes t ingTes t ing(V ib ra t ion Test -(V ib ra t ion Test - D i rec t i onD i rec t i on3 )3 )


23/29



3) Tensile Test

4Procedure:Apply a load of 445 N for 1 minute.

4Requirement:

The samples must withstand the load with no slippage.

Electrical resistance must not exceed 30 m.

4) Temperature and Humidity Cycling Test

4Procedure:

Cycle: 3 h at 4 oC + 6h at 32 oC, relative humidity of 90 to 95% - 30 days.

4Requirement:Electrical resistance must not exceed 30 m


24/29

T G C -T G C - Tes t ingTes t ing( Tem pe rat u r e - Hum id i t y Test ) (Tem pe rat u r e - Hum id i t y Test )


25/29



5) H2S Exposure Test4Procedure:The samples must be placed in a desiccator in an oven at

a temperature of 65 C. Once the temperature has been reached the

H2S must be injected until a given pressure has been reached and

these conditions must be maintained for 1 hour. After this exposure,

the samples must be removed from the desiccator and submitted to a

temperature of 65 C for an additional hour.

4Requirement:Electrical resistance must not exceed 30 m.


26/29


27/29



6) Salt Fog Test

4Procedure:30 days in a salt fog chamber.

4Requirement:Electrical resistance must not exceed 30 m.

7) Fault Current Test

4Procedure:Apply a current of 1 000 A for 20 s.

4Requirement:After the current application, samples should meet the

Pullout Test requirements.


28/29


BellcoreBellcoreTR-NWT-001075TR-NWT-001075::8) Pullout Test

44Procedure:Apply a load of 155 N for 01 minute.

44Requirement:

Samples should withstand the load with no slippage.

Electrical resistance must not exceed 5 M, in relation to the previous measurement.

9) Lightning Surge Test

4Procedure:Apply a current of 20 kA in 8/20 s.

4Requirement:

Electrical resistance should not exceed 5 M, in relation to the previous measurement.

After the current application, samples should meet the Pullout Test

requirements.


29/29

TGC

GUARANTEE OF SUPERIOR CONNECTIONS IN

GROUNDING SYSTEMS

Conector TGC Presentacion

Documents

Transcript of Conector TGC Presentacion