1. Construccion de Un Modelo de Pozo
-
Upload
fernando-aybar -
Category
Documents
-
view
215 -
download
0
Transcript of 1. Construccion de Un Modelo de Pozo
-
7/28/2019 1. Construccion de Un Modelo de Pozo
1/23
EX 1.1Example 1
FloSystem User Course
Well Model Building and Calibration
Naturally Flowing Oil Well
-
7/28/2019 1. Construccion de Un Modelo de Pozo
2/23
EX 1.2Overview
Data Entry
Well Deviation Data
Well Completion Data
Reservoir Fluid Data
Reservoir Rock Data
Measured Data
Data Matching Inflow / Outflow curves
Pressure-Depth profiles
-
7/28/2019 1. Construccion de Un Modelo de Pozo
3/23
EX 1.3Well Details
Mid-perf depth - 8500 ft MD
4.5 OD, 4 ID, 11.6 ppf tubing to 3460 ft MD
3.5 OD, 3 ID, 9.2 ppf tubing to 5000 ft MD
2.875 OD, 2.441 ID, 6.4 ppf tubing to 7000 ft MD
7 OD, 6.3 ID, 23 ppf casing to 8500 ft MD
Oil 38 API Water Gravity: 1.1
Gas Gravity: 0.82 GOR : 400 scf/stb
Water-cut: 17% Res. Press.: 3800 psia Pb : 1850 psia Res. Temp.: 187 oF
PI: 3.6 stb/day/psi Bo : 1.2 rb/stb
-
7/28/2019 1. Construccion de Un Modelo de Pozo
4/23
EX 1.4Dataprep General
Select File - New
Select DataPrep - General
Report Labelling
-
7/28/2019 1. Construccion de Un Modelo de Pozo
5/23
EX 1.5Datum
Double-click on Xmas Tree
Enter Datum details
-
7/28/2019 1. Construccion de Un Modelo de Pozo
6/23
EX 1.6
Rotary Kelly Bushing
Wellhead Elevation
Mean Sea Level
Sea Bed
Datum
-
7/28/2019 1. Construccion de Un Modelo de Pozo
7/23
EX 1.7Deviation Data
Select Dataprep - Deviatio n Data - Well Data
Insert three lines, enter MD, TVD pairs - edit last
row to 8500, 7500
-
7/28/2019 1. Construccion de Un Modelo de Pozo
8/23
EX 1.8Well Components
Select Dataprep - Equipment Data - Well Data
Enter data (node depth is BOTTOM of component)
-
7/28/2019 1. Construccion de Un Modelo de Pozo
9/23
EX 1.9Well Components
Select Con fig - PreferencesView Component name only
Try changing view from text to icons using View- Disp lay as TextorDisplay as icons
In Config-Preferences, view MD, componentdata, etc.
-
7/28/2019 1. Construccion de Un Modelo de Pozo
10/23
EX 1.10Completion Editing
Go Back to Deviation Data
Highlight 7000 - Insert Row
Enter MD 6000 and TVD 5200 Note that a new node has been inserted in
Tubing 3
Double-click on the lower section of Tubing 3
Re-label as Tubing 3b. Call the upper partTubing 3a.
Select Con figure - Preferencesand include allthe options in the text display
-
7/28/2019 1. Construccion de Un Modelo de Pozo
11/23
EX 1.11PVT Data Entry
Select Dataprep - Reservo ir Con tro l - FluidParameters
Enter
Oil Gravity 38 API
Gas Gravity 0.82
Water Gravity 1.1
GOR 400 scf/STB
Water Cut 17 %
Select Check:Pressure 3800 psi, Temp 187 oF
Note Glasos correlation results
Pb =1715 psi, Bo = 1.20129
-
7/28/2019 1. Construccion de Un Modelo de Pozo
12/23
EX 1.12PVT Data Matching
Select Match, change temp to 187 oF, enter 1850psi beside temp and Calculate
Note Pb = 1715 psi. Press Best Fit Note new Pb = 1850 PSI
Select Form. Vol. Factor as Match Property
Change pressure to 3800 psi
Enter 1.20 as Bo beside 187 oF, 3800 psi field Calculate - Best Fitto tune Bo
Glasos correlation is now tuned for usethroughout the well model
-
7/28/2019 1. Construccion de Un Modelo de Pozo
13/23
EX 1.13IPR Data Entry
Select Manual Entry model and Edit Layer
Enter layer pressure = 3800 psi, temp = 187 oF
and PI = 3.6 STB/day / psi Select Choo se IPRand Vogel, then Plot
Minimise graphing window
Select Norm . Pseudo Pressu reand Plot
Select Straight Lineand Plot
Note that all three IPRs are plotted on the samegraph
-
7/28/2019 1. Construccion de Un Modelo de Pozo
14/23
EX 1.14IPR Data Entry (contd.)
Maximise graphing window
Double Click on Y axis, note that the Round optionis selected
Note the other options Click Edit , observe options of changing axes, titles,
activate the coordinates and add a description of thegraph.
You can save the graph configuration as a template(File - Save Temp late)and also print it. (File - Print )
Close the graphing window and select Vogel modelfor use in the rest of the exercise
Select OK until returned to the icon display
-
7/28/2019 1. Construccion de Un Modelo de Pozo
15/23
EX 1.15Measured Data
Use Notepad to view the file EX1.RVP (ASCIIFile)
This file contains one line - 5900 2200 - the first
number is observed surface flowrate in STB andthe second is well flowing pressure at that rate -this is the measured data to which we will matchthe model
Return to WellFlo Select File - Load Measu red Data -
Flow rate versus Pressu re
Load EX1.RVP - note one pair of values reportedas read , it is possible to load multiple pairs.
Display on the Choo se IPRplot.
-
7/28/2019 1. Construccion de Un Modelo de Pozo
16/23
EX 1.16Well Model Tuning
Select Analysis - Operat ing point
Select Edit Rates
Select Rate in lower left of screen / 1000 / 10,000 and 9
steps, select Filland OK
Tatm. = 60oF Pwh = 200 psia (Top node Xmas Tree)
Check Sensit iv i tyOff (both)
Set Correlat ionto Duns and Ros(std)
Select Calculateand on completion of calculationResults and Plot .
Selecting Measu red Data on then Plot to see theInf low /Outf lowplot
-
7/28/2019 1. Construccion de Un Modelo de Pozo
17/23
EX 1.17Well Model Tuning
Note that the model represents a reasonablematch to observed data.
On Nodal Analysisscreen select Sensit iv i t ies
Select Flow Correlat ionas sensitivity 1 and edit (1) Duns and Ros (std); (2) Beggs and B r i ll (std)
(3) Hagedorn and Brown (std); (4) Orkizewski
Return to Nodal Analysis. Switch Sensit iv i ty1 on
and Calculate. On completion, select Results and Plot and A llValues for sensitivity 1 and Plot again
The four outflow curves are plotted with the IPR
-
7/28/2019 1. Construccion de Un Modelo de Pozo
18/23
EX 1.18
Well Model Tuning
Zoom on the region of the plot where theintersections and observed data are.
Switching on Iterate To Exact Operating Poin twill give a more accurate operating point. Thisoption should always be used.
Note that Hagedorn & B rown(std)comesclosest to the observed data.
To get a better match, tune the correlation to themeasured data using the L- factor as asensitivity.
L modifies the computed pressure gradients.
An acceptable range for L is 0.9 to 1.1.
-
7/28/2019 1. Construccion de Un Modelo de Pozo
19/23
EX 1.19
How should the productivity index be changedto obtain a match on the inflow curve?
What other reservoir parameter could be the
cause of the slight mismatch? What else could be at fault?
Well Model Tuning
-
7/28/2019 1. Construccion de Un Modelo de Pozo
20/23
EX 1.20
Well Model Tuning
Return to the Fluid Parameterssection and re-tune the formation volume factor to 1.3
Repeat the calculation with the same sensitivity
values and note that the observed data nowplots closer to the Duns and Roscorrelationoutflow curve.
Return the Bo tuning to 1.2 and select theHagedorn and Brow n(std)correlation.
Switch off sensitivity and calculate and plot theinflow/outflow curve.
Note the well flowrate reported on the graph
Return to graphical editor.
-
7/28/2019 1. Construccion de Un Modelo de Pozo
21/23
EX 1.21
Well Model TuningPressure vs Depth
Select File - Load Measured Data - Depth (MD)vs.Pressure (and Temp), & load EX1.DVP
Select Analysisand Pressure Dropand enter theoperating rate you just obtained
start node is Xmas Tree at 200 psia
solution node (end node) is Casing (mid-perfs)
Calculate and plot results as Pressure vs.
Measured Depth, including measured data Try Operat ing Poin tcalculation mode withIterate to exactswitched on. This willautomatically provide you with a pressure-depthplot at the appropriate operating rate.
-
7/28/2019 1. Construccion de Un Modelo de Pozo
22/23
EX 1.22
Data MatchingPressure vs.Depth
Return to Pressure-Drop Calcu lat ion, switch onsensitivity 1 (flow correlations) and Calculate.
Now plot pressure versus depth with A ll valuesset in the sensitivity option.
The Hagedorn and Brown (std) correlation givesthe best match to the whole flowing gradientsurvey.
Switch off Sensitivity 1. Reverse the Pressure-Dropcalculation with start node as casing (whatpressure?), and solution node as Xmas tree.
Compare the computed and measured data,
especially the THP.
-
7/28/2019 1. Construccion de Un Modelo de Pozo
23/23
EX 1.23
Summary
A naturally flowing oil well was used todemonstrate model building and calibration
The same procedures can be applied to oil wellson artificial lift (gas-lift or ESP), gas andcondensate producers and gas or waterinjectors.