Post on 25-Sep-2018
INSTITUTO NACIONAL DE NORMALIZACION
01 201 Anexo
ALCANCE DE LA ACREDITACION DE LA CATOX LTDA., CONCON, COMO ORGANISMO DE INSPECCION, TIPO A
AREA : ENSAYOS NO DESTRUCTIVOS
Método de inspección Líquidos penetrantes
Producto Uniones soldadas en línea de: cañerías, tuberías, oleoductos, gasoductos, poliductos, acueductos incluidos subterráneos submarinos.
Norma/Especificación PG-LP, 2013,
basado en ASTM E 165-2012
ASME I, VIII, V:2013, Art.6 ANSI 133.1-2014,
ANSI 1331.3-2014, ANSI 1331.4-2012
API 1104-2010 PG-RX-USOLD, 2013,
PG-RX-CAÑERIAS basados en
API-1104, 2013 ASME V, ed. 2010 API 1104, ed. 2005
ASTM E 94 ASTM E 999
PO-GAMMA, 2012, basado en
ASME 1, VIII, V: 2013, Art. 2 y 22 ANSI 1331.1-2014, ANSI 631.3-2014, ANSI 1331.4-2012, ANSI 1331.8-2014
API 1104-2010, 570, 51-, 2000. ASTM E 94
AWWA- M11-1 989 PG-PM, 2013,
basado en ASTM E 709:2014
ASME 1, VIII, V: 2013, Art.7 ANSI 1331.3-2014
API 1104:2010 PG-INSP-VISUAL, 2012 INSP-USOLD-041, 2015
INSP-IV-USOLDCAÑ-008, 2015 INSP-MEPLCAÑ-029, 2014,
basados en ASME 1, VIII, V: 2013, Art. 9 PG-PRUEBA-H-PN, 2011
INSP-PI-R-015, 2013 INSP-PVACI0-044, 2014,
basados en ASME 1, VIII, V: 2013, Art. 10.
NCh 990:1973 INSP-MD-027, 2013,
basado en ASTM A 1038:2013,
E92:2003.
Radiografía industrial
Partículas magnéticas
Inspección visual, dimensional
Prueba hidráulicas y Pruebas neumáticas
Medición de dureza Superficial Vickers Método UCI
115
INSTITUTO NACIONAL DE NORMALIIZACION
01 201 Anexo
Producto Norma/Especificación Método de inspección PE-UT-PLANCHA, 2013 Ultrasonido:
PE-UT-SOLDADURA, 2013 Phased Array INSP-UT-USOLD-018, 2015 B Scan
INSP-BSCAN-026, 2015 A Scan INSP-TOFD-048, 2015, TOFO
basados en ASME 1, VIII, V:2013, Art.4, 5 y 23
ASTM E 2700:2014 ANSI B31. 1-2014 ANSI B31. 3-2014 ANSI B31. 4-2012 ANSI B31.8-2014
API 1104:2010, API 570, API 51-:2000 ASTM D4541:2009 Control de adherencia
NCh 2154:1991 por tracción INSP-1-101-YDT-020, 2015, Inspección de revestimiento
basado en exterior e interior ASTM 05162:2008, G62:2007
NACE E2700:2014 Componentes, piezas, fitting y PG-INSP-VISUAL, 2012 Inspección visual, uniones soldadas de: INSP-USOLD-041, 2015 Inspección dimensional Estructuras metálicas, INSP-IV-USOLDCAÑ-008, 2015 Componentes estructurales, INSP-MEPLCAN-029, 2014, Instalaciones Industriales, basados en Estanques y recipientes ASME 1, VIII, V: 2013, Art.9 Incluidos subterráneos, ASME-VIII-201 3 Válvulas, Bombas, ANSI -B31.3-2014 Compresores, Elementos AWS D11:2010. marítimos, Tubos de API 650:2013 calderas y de API 620:2013
PG-PM, 2013, Partículas magnéticas intercambiadores de calor, Equipos rotatorios, basado en
ASME 1, VIII, V: 2013, Art.7. AWS 01.1:201 0.
PG-LP, 2013, Líquidos penetrantes basado en
ASTM E 165-2012. ASME V: 2013, Art.6.
ASME VIII: 2013. AWS D11:2010.
PE-UT-PLANCHA, 2013 Medición de espesor por PE-UT-SOLDADURA, 2013 Ultrasonido INSP-UT-USOLD-01 8, 2015 Phased Array
INSP-BSCAN-026, 2015 A Scan INSP-TOFD-048, 2015, B Scan
basados en TOFD AWS 01.1:2010 ANSI B31.3-2014 ASTM E 797:2010
ASME 1, VII I,V:2013, 1
PG-RX-USOLD, 2013 Radiografía industrial PG-RX-CAÑERIAS API-1 104, 2013
PO-GAMMA, 2012, basados en
215
INSTITUTO NACIONAL DE NORMALIZACION
01 201 Anexo
Producto Norma/Especificación Método de inspección ASME V:2013, Art.2 y22
ASME 1, VIII, IX:2013 AWS D11:2010 ANSI 13301-2009 ANSI B30,3:2012 ANSI 1330.8:2010 ASTM_E94:2010
PG-PRUEBA-H-PN, 2011 Prueba hidrostática y INSP-PH-R-015, 2013 Prueba neumática
INSP-PVACIO-044, 2014, basados en
ASME V:2013, Art.10 ASME 1, VIII, IX:2013
API 620:2013 API_650:2013
INSP-MD-027, 2013, Medición de dureza basado en Superficial Vickers,
ASTM Al 038:2013 Método UCI ASTM_E92:2003
INSP-CEDDY-TUBOS-040, 2015, Ensayo Corrientes Eddy en basado en Tubos de intercambiadores
ASME_1,_VIII,_V:2013,_Art.8. INSP-PMI-031, 2015, Ensayo de PMI
basado en (Identificación positiva de ASME II: 2013, A,B,C materiales) ASME 1316.34:2013
API_578:2010 INSP-AVR-046, 2013 Análisis de vibración INSP-AVR-047, 2013,
basados en API 541-546-611-612-617
ISO 3945:1985 (W) SO 10816-1:1995 ¡SO 10816-8:2014 ISO_19201 :2013
INSP-PBA-VI-013, 2013, Prueba hidrostática y prueba basado en neumática
API 598:2009, API 594:2010, API 599:2013, API 600:2015, API 602:2009,
API 603:2013, API 608:2012, API 609:2009
Estructuras de acero al PG-INSP-VISUAL, 2012 Inspección visual, carbono, INSP-USOLD-041, 2015, Inspección dimensional aceros inoxidables, basados en Cables de acero, Puentes ASME :2013, ASME VIII,Div.1, Div.2; metálicos, Maquinarias de uso ASME IX:2013. minero e hidromecánico, ANSI 1330.1:2009, ANSI 830.2:2010, Equipos de movimiento de ANSI 1330.3:2014, ANSI B30.4:2010, tierra, Puente ANSI 830.5:2014, ANSI 330.7:2009, Grúa y Grúas móviles. ANSI 1330.8:2014, ANSI B30.9:2009,
ANSI 1330.10:2014, ANSI 1330.11:2010, ANSI 1330.16:2012, ANSI B30.20:2013,
ANSI 1330.22:2010. AWS_D1.1:2010,_AWS_D1.2:2014.
315
INSTITUTO NACIONAL DE NORMALIZACION
01 201 Anexo
Producto Norma/Especificación Método de inspección AWS 01.3:2008, AWS 01.5:2010, AWS
D1.5:2010, AWS Dl .6:2007, AWS Dl .14.3:2010.
API 570:2009, API 620: 2013, API 653:2014, API 51-2012, API 1104:2013, DOT 406, DOT 407, DOT 412, MC 330,
MC 331. NCh 885:1972 NC 990:1973
NCh_2087:2000 PG-LP, 2013, Líquidos penetrantes
basado en ASTM E 165-2012.
ASME 1, VIII, V:2013, ANSI B30.1:2009, ANSI 1330.2:2011
ANSI 1330.04:2010, ANSI B30.05:2014, ANSI 1330.16:2012, ANSI 1330.07:2011, ANSI 1330.09:2014, ANSI 1330.11:2010 ANSI B30.1 1:2010, ANSI B31 .1:2014,
ANSI 1331.3:2014, AWS D1:2010 API 650:2013, API 651.2014,
API_1104:201 3,_NCh_990:1973 PE-UT-PLANCHA, 2013 Medición de espesor por
PE-UT-SOLDADURA, 2013 Ultrasonido INSP-UT-USOLD-01 8, 2015 Phased Array
INSP-BSCAN-026, 2015 A Scan INSP-TOFD-048, 2015, B Scan
basados en TOFO ASTM E 797:2010, ASTM E273, ASTM
E317, ASTM E164, ASME 1, VIII, V:2013,
ANSI 1330.1:2009, ANSI 1330.2:2011 ANSI B30.04:2010, ANSI B30.05:2014, ANSI 1330.16:2010, ANSI 1330.10:2009, ANSI 1330,11:2010, ANSI 1330.20:2013,
ANSI 1330,22:2010 PG-RX-USOLD, 2013 Radiografia industrial
PG-RX-CANERIAS API-1 104, 2013 PO-GAMMA, 2012,
basados en ASME 1, y, VIII:2013,
ANSI 1330.1:2009, ANSI 1330.2:2011 ANSI 1330.04:2010, ANSI 1330.05:2014, ANSI 1330.16:2012, ANSI B30.07:2011, ANSI 1330.20:2010, ANSI 1330.22:2010, ANSI 1330.10:2010, ANSI 1330.09:2014,
ANSI 1330.11:2013, AWS 01.1:2010
415
INSTITUTO NACIONAL DE NORMALIZACION
01 201 Anexo
Producto Norma/Especificación Método de inspección Piezas fundidas INSP-MD-027, 2013, Medición de Dureza Piezas forjadas basado en Superficial Vickers
ASTM A956:2012 Método UCI ASTM_A1038:2013
PG-LP, 2013, Líquidos penetrantes basado en
ASTM_E_165-2012 ASTM G12-07 Medición de espesores SSPC-PA2-09 de recubrimientos
PE-UT-PLANCHA, 2013 Ultrasonido PE.-UT-SOLDADURA, 2013 INSP-UT-USOLD-018, 2015
INSP-BSCAN-026, 2015 INSP-TOFD-048, 2015,
basados en ASTM E797:2010 ASTM A388:2011 ASTM_A609:2012
PO-PM, 2013, Partículas magnéticas basado en
ASTM_E709:2014 Procesos de soldaduras PG-LP, 2013, Líquidos penetrantes
basados en ASTM E 165-2012
ASME IX:2013, AWS_01.1:2010 PG-PM, 2013, Partículas magnéticas
basado en ASTM E709:2014 ASME IX:2013, AWS_D 1 .1:201 0
PG-RX-USOLD, 2013 Radiografía industrial PG-RX-CAÑERIAS API-1104, 2013
PO-GAMMA, 2012, basados en
ASME 1, y, VII1:2013, ANSI 1330.1:2009, ANSI 1330.2:2011
ANSI 1330.04:2010, ANSI 1330.05:2014, ANSI 1330.16:2012, ANSI 1330.07:2011, ANSI 1330.20:2010, ANSI 1330.22:2010, ANSI 1330.10:2010, ANSI 1330.09:2014,
ANSI B30.11:2013, AWS D11:2010 API_1104:2013.
,.:
;
t
()
(•,.
' .1
rdo CebaIIo Osorio División Acreditación
Sergio oroG ,7cto
;
Mos,
515