CAP. IV REDES DE TUBERIAS UNSCH, Escuela Profesional de Ingeniería Civil MECANICA DE FLUIDOS II...

Post on 24-Jan-2016

235 views 0 download

Transcript of CAP. IV REDES DE TUBERIAS UNSCH, Escuela Profesional de Ingeniería Civil MECANICA DE FLUIDOS II...

CAP. IVREDES DE TUBERIAS

UNSCH, Escuela Profesional de Ingeniería Civil

MECANICA DE FLUIDOS II

21/04/23 1Ing. Jaime L. Bendezú Prado

ESTUDIO DE REDES DE TUBERIAMETODO DE HARDY CROSS

Es un método de aproximaciones sucesivas que determina el caudal que discurre por cada

tubería y el sentido de flujos. Q 1 Q1-2 2 Q2-3 3 Q3

III

Q1-6 I Q2-5 Q2-4 Q3-4 + -

II 3CIRCUITOS Y 6

NUDOS

6 Q6-5 5 Q5 Q4-5 4 Q4

21/04/23 2Ing. Jaime L. Bendezú Prado

METODO DE HARDY CROSS

PROCEDIMIENTO:Como una aproximación se asume una

distribución de caudales iniciales en cada tramo.Qo = Caudal inicial aprox. En un tramo (asumir)hfo = kQon (perdida inicial aproximado)Q = Qo + ΔQ = siguiente caudal aproximadohf = k(Qo+ ΔQ)n = Siguiente perdida aprox.Si : ΔQ < 1%Q Q será el caudal verdadero de lo contrario se sigue los mismos pasos

tomando como nuevo Qo = Q hasta que ΔQ < 1%Q y alrededor de cada circuito ∑hf =0 y

Q en tramos comunes serán iguales.

21/04/23 3Ing. Jaime L. Bendezú Prado

METODO DE HARDY CROSS

∑hf = ∑ho + ΔQ ∑(nhfo/Qo)

Donde: ΔQ = - ∑hfo/(n∑hfo/Qo)

hf = 1745155.28LQ1.85/(C1.85 D4.85) Hazen y

Williams

hf = 0.0826 fLQ2/D5 Darcy

21/04/23 4Ing. Jaime L. Bendezú Prado

METODO DE HARDY CROSS1.- La ecuación de la continuidad se debe cumplir en cada

momento.

* En el sistema:

Qingreso = Qsalida

Q = Q3 + Q4 + Q5

* En cada nudo En el nudo 1 : Q = Q1-2 + Q1-6

En el nudo 2 : Q1-2 = Q2-3 + Q2-4 + Q2-5

En el nudo 3 : Q2-3 = Q3-4 + Q3

En el nudo 4 : Q2-4 + Q3-4 = Q4-5 + Q4

21/04/23 5Ing. Jaime L. Bendezú Prado

En el nudo 5 : Q5 = Q2-5 + Q6-5

En el nudo 6 : Q1-6 = Q6-5

21/04/23 6Ing. Jaime L. Bendezú Prado

METODO DE HARDY CROSS2.- La suma algebraica de perdida de cargas de cada

circuito debe ser cero.

* Circuito I :

hf1-2 + hf2-5 + hf6-5 + hf1-6 = 0

* Circuito II :

hf2-4 + hf4-5 + hf2-5 = 0

* Circuito III :

hf2-3 + hf3-4 + hf2-4 = 0

Donde: hf = kQn

n = 2 (si Darcy)

n = 1.85 (si Hazen y Williams)21/04/23 7Ing. Jaime L. Bendezú Prado

Aplicación

METODO DE LINEALIZACION

21/04/23 9Ing. Jaime L. Bendezú Prado

f

f

21/04/23 10Ing. Jaime L. Bendezú Prado

21/04/23 11Ing. Jaime L. Bendezú Prado

f